Search Results

Standard

Thrust Washers – Design and Application

2011-06-13

CURRENT

J924_201106

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

TURBOCHARGER NOMENCLATURE AND TERMINOLOGY

1979-11-01

HISTORICAL

J922_197911

This recommended practice applies to nomenclature of turbo-charger parts and terminology of performance. Modifying adjectives are omitted in some cases for the sake of simplicity. However, it is considered good practice to use such adjectives when they add to clarity and understanding.

Standard

THRUST WASHERS—DESIGN AND APPLICATION

1995-02-01

HISTORICAL

J924_199502

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

THRUST WASHERS—DESIGN AND APPLICATION

1981-01-01

HISTORICAL

J924_198101

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

Spring-Loaded Clutch Spin Test Procedure

2012-10-23

CURRENT

J1073_201210

This SAE Recommended Practice applies to spring-loaded clutches such as are used with manual shift type transmissions.

Standard

Spark Arrester Test Carbon

2013-03-26

HISTORICAL

J997_201303

This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.

Standard

SPLIT TYPE BUSHINGS—DESIGN AND APPLICATION

1995-02-01

HISTORICAL

J835_199502

This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques, and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.

Standard

SPLIT TYPE BUSHINGS - DESIGN AND APPLICATION

1981-12-01

HISTORICAL

J835_198112

This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.

Standard

SPARK ARRESTER TEST PROCEDURE FOR MEDIUM SIZE ENGINES

1991-01-01

HISTORICAL

J350_199101

This SAE Recommended Practice establishes equipment and procedures for testing spark arresters used on medium-size, single-position internal combustion engines, normally used in transportable, stationary, and vehicular applications, such as highway trucks, agricultural tractors, industrial tractors, other mobile equipment, and motorcycles. This document provides two methods of testing (laboratory testing and engine testing) which may be used to evaluate a spark arrester. It also includes special requirements for screen type devices and an endurance test procedure for screen type spark arresters.

Standard

SEALS—APPLICATION GUIDE TO RADIAL LIP

1979-04-01

HISTORICAL

J946D_197904

Standard

SEALS: APPLICATION GUIDE TO RADIAL LIP

1988-06-01

HISTORICAL

J946_198806

Standard

SEALS: APPLICATION GUIDE TO RADIAL LIP

1987-02-01

HISTORICAL

J946_198702

Standard

PROCEDURE FOR MEASURING BORE AND FACE RUNOUT OF FLYWHEELS, FLYWHEEL HOUSINGS, AND FLYWHEEL HOUSING ADAPTERS

1993-04-01

HISTORICAL

J1033_199304

This SAE Recommended Practice applies to any internal combustion engine which can utilize SAE No. 6 thru SAE No. 00 size flywheel housing. It provides instructions for correcting flywheel housing bore runout readings which are influenced by crankshaft bearing clearance. Limits for bore and face runout are specified in the various SAE Standards and Recommended Practices covering flywheels and flywheel housings.

Standard

PROCEDURE FOR MEASURING BORE AND FACE RUNOUT OF FLYWHEELS, FLYWHEEL HOUSINGS AND FLYWHEEL HOUSING ADAPTERS

1988-11-01

HISTORICAL

J1033_198811

This recommended practice applies to any internal combustion engine which can utilize SAE No. 6 thru SAE No. 00 size flywheel housing. It provides instructions for correcting flywheel housing bore runout readings which are influenced by crankshaft bearing clearance. Limits for bore and face runout are specified in the various SAE Standards and Recommended Practices covering flywheels and flywheel housings.

Standard

Overcenter Clutch Spin Test Procedure

2012-10-23

CURRENT

J1079_201210

This SAE Recommended Practice applies to driving ring type overcenter clutches such as are used in industrial power takeoffs.

Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression

2020-10-06

CURRENT

J335_202010

This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.

Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression

2012-10-23

HISTORICAL

J335_201210

This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.

Standard

Methane Measurement Using Gas Chromatography

2011-09-06

CURRENT

J1151_201109

This SAE Recommended Practice describes instrumentation for determining the amount of methane in air and exhaust gas.

Standard

Measurement of Intake Air or Exhaust Gas Flow of Diesel Engines

2011-06-13

CURRENT

J244_201106

This procedure establishes recommendations on the measurement of diesel engine intake air flow under steady-state test conditions. The measurement methods discussed have been limited to metering systems and associated equipment found in common usage in the industry, specifically, nozzles, laminar flow devices, and vortex shedding. The procedure establishes accuracy goals as well as explains proper usage of equipment. The recommendations concerning diesel engine exhaust mass flow measurements are minimal in scope.

Standard

Measurement of Carbon Dioxide, Carbon Monoxide, and Oxides of Nitrogen in Diesel Exhaust

2002-10-21

CURRENT

J177_200210

The method presented applies to the analysis of the indicated constituents in diesel engine exhaust, or vehicles using diesel engines, when operating at steady-state conditions. The measurements of carbon monoxide, carbon dioxide, and nitric oxide are based on continuous sampling and analysis by nondispersive infrared (NDIR) methods. Measurement of total oxides of nitrogen by chemiluminescence and NDIR methods is discussed. This SAE Recommended Practice provides for the measurement of carbon dioxide, carbon monoxide, and oxides of nitrogen in diesel exhaust.