Search Results

Experiments were conducted on a turbocharged three cylinder automotive common rail diesel engine with port injection of butanol. This dual fuel engine was run with neat butanol and blends of water and butanol (up to 20% water by mass). Experiments were performed at a constant speed of 1800 rpm and a brake mean effective pressure of 11.8 bar (full load) at varying butanol to diesel energy share values while diesel was either injected as a single pulse or as twin pulses (Main plus Post). Open engine controllers were used for varying the injection parameters of diesel and butanol. Water butanol blends improved the brake thermal efficiency by a small extent because of better combustion phasing as compared to butanol without water. When the butanol to diesel energy share was high, auto-ignition of butanol occurred before the injection of diesel. This lowered the ignition delay of diesel and hence elevated the smoke level.

Almost one-third of the fuel energy is wasted into the atmosphere via exhaust gas from an internal combustion engine. Despite several advancements in waste heat recovery technology, single-cylinder engines in the market that are currently in production remain naturally aspirated without any waste heat recovery techniques. Turbocharging is one of the best waste heat recovery techniques. However, a standard turbocharger cannot be employed in the single-cylinder engine due to technical challenges such as pulsated flow conditions at the exhaust, phase lag in the intake and exhaust valve opening. Of late, the emphasis on reducing exhaust emissions has been a primary focus for any internal combustion engine manufacturer, with the onset of stricter emission norms. Thus, the engine designer must prioritize emission reduction without compromising engine performance.

Adopting a low compression ratio (LCR) is a viable approach to meet the stringent emission regulations since it can simultaneously reduce the oxides of nitrogen (NOx) and particulate matter (PM) emissions. However, significant shortcomings with the LCR approach include higher unburned hydrocarbon (HC) and carbon monoxide (CO) emissions and fuel economy penalties. Further, poor combustion stability of LCR engines at cold ambient and part load conditions may worsen the transient emission characteristics, which are least explored in the literature. In the present work, the effects of implementing the low compression ratio (LCR) approach in a mass-production light-duty vehicle powered by a single-cylinder diesel engine are investigated with a major focus on transient emission characteristics.

Methanol has a very low cetane number but it can be used in the neat form in a glow plug based hot surface ignition (HSI) engine at CI engine compression ratios. A CFD simulation model of a glow plug assisted methanol HSI engine was developed and validated using experimental data reported in literature. A study on the effect of single and multipulse injection of methanol, glow plug surface temperature, injection pressure and effect of shielding it were conducted by applying the model on to a three cylinder neat methanol HSI engine. A glow surface temperature of 1273 K was found to be sufficient for ignition of methanol at 50% load while the distance between the glow plug and the injector affected the ignition delay. The sprays were ignited sequentially starting from the one closest the glow plug which resulted in extended combustion. Injecting methanol in double pulses reduced the Maximum Rate of Pressure Rise (MRPR).

In the present work, experiments were conducted on a single cylinder, three-wheeler, spark ignition engine operating with hydrogen as a fuel. In this work, hydrogen was inducted through the intake manifold to the engine. The engine was always operated with wide-open throttle (WOT). To vary the output, the equivalence ratio was varied. For all outputs, the spark timing was set for MBT (minimum advance for best torque). For each output, performance, emission and combustion parameters were recorded and analyzed. For comparison of results, with the same engine, the experiments were also conducted with gasoline as a fuel using a conventional carburetor. It was observed that the hydrogen engine produces less maximum power than its gasoline counterpart. From the analysis of the results, it was found that the efficiency of hydrogen engine was quite higher than gasoline engine at optimized conditions at all the operating points.

Use of water diesel emulsions in diesel engines has resulted in drastic reductions in NOx and smoke levels, while the thermal efficiency is also improved. The objective of this work is to evaluate the effects of using water diesel emulsion as the pilot fuel in a dual fuel engine with LPG as the primary fuel. Tests were conducted on a single cylinder constant speed DI diesel engine. An emulsion with a water to diesel ratio of 0.4:1 was used. Performance, HC, CO, NOx, smoke emissions and combustion parameters were obtained and compared with the case where pure diesel was used as the pilot fuel. At high loads, the brake thermal efficiency with the emulsion as the pilot fuel was better than that with diesel. NOx levels were drastically reduced. The already low smoke levels were reduced further with the emulsion. There was an adverse effect on HC and CO emissions. The maximum rate of pressure rise and peak pressure were also higher with the emulsion.

The present work investigates the effects of lowering the compression ratio (LCR) from 18:1 to 14:1 and optimizing the fuel injection parameters across the operating range of a mass production light-duty diesel engine. The results were quantified for a regulatory Indian drive cycle using a one-dimensional simulation tool. The results show that the LCR approach can simultaneously reduce the oxides of nitrogen (NOx) and soot emissions by 28% and 64%, respectively. However, the unburned hydrocarbon (HC) and carbon monoxide (CO) emissions increased significantly by 305% and 119%, respectively, with a 4.5% penalty in brake specific fuel consumption (BSFC). Hence, optimization of fuel injection parameters specific to LCR operation was attempted. It was evident that advancing the main injection timing and reducing the injection pressure at low-load operating points can significantly help to reduce BSFC, HC and CO emissions with a slight increase in the NOx emissions.

The property of methanol to surface ignite can be exploited to use it in a diesel engine even though its cetane number is very low. Poor lubricity of methanol is still an issue and special additives are needed in order to safeguard the injection system components. In this work a common rail three cylinder, turbocharged diesel engine was run in the glow plug based hot surface ignition mode under different injection strategies with methanol as the main fuel in a blend with n-butanol. n-Butanol was used mainly to enhance the viscosity and lubricity of the blend. The focus was on the effect of different injection strategies. Initially three blends with methanol to n-butanol mass ratios of 60:40, 70:30 and 80:20 were evaluated experimentally with single pulse fuel injection. Subsequently the selected blend of 70:30 was injected as two pulses (with almost equal mass shares) with the gap between them and their timing being varied.

In many Asian countries a significant automobile market share is held by two and three wheelers. Generally, cost and simplicity considerations limit the performance and emission levels of small engines. Methanol is an excellent alternative fuel for SI engines due to its high-octane number, high flame speed, presence of oxygen in its molecule and thus can be used to enhance the performance of small engines. However, use of neat methanol in SI engines poses constraints due to low energy density and poor vaporization characteristics. Also, the effectiveness of methanol as a fuel has still to be thoroughly investigated in small-bore SI engines in order to assess its potential. In this work, a small-bore 200cc three-wheeler automotive engine was modified to operate in the port fuel injection mode with neat methanol as the fuel.

Supercharging a single-cylinder diesel engine has proved to be a viable methodology to reduce engine-out emissions and increase full-load torque and power. The increased air availability of the supercharger (SC) system helps to inject more fuel quantity that can improve the engine's full-load brake mean effective pressure (BMEP) without elevating soot emissions. However, the increased inlet temperature of the boosted air and the availability of excess oxygen can pose significant challenges to contain oxides of nitrogen (NOx) emissions. Hence, it is important to investigate the potential NOx reduction options in supercharged diesel engines. In the present work, the potential of low-pressure exhaust gas recirculation (LP EGR) was evaluated in a single-cylinder supercharged diesel engine for its benefits in NOx emission reduction and impact on other criteria emissions and brake specific fuel consumption (BSFC).