Search Results

Engine valve flow coefficients are not only used to characterize the performance of valve/port designs, but also for modelling gas exchange in 0D/1D engine simulation. Flow coefficients are usually estimated with small pressure ratios and at ambient air conditions. In contrast, the ranges for pressure ratio, pressure and temperature level during engine operation are much more extensive. In this work the influences of these three parameters on SI engine poppet valve flow coefficients are investigated using 3D CFD and measurements for validation. While former investigations already showed some pressure ratio dependencies by measurement, here the use of 3D CFD allows a more comprehensive analysis and a deeper understanding of the relevant effects. At first, typical ranges for the three mentioned parameters during engine operation are presented.

Engine valve flow coefficients are used to describe the flow throughput performance of engine valve/port designs, and to model gas exchange in 0D/1D engine simulation. Valve flow coefficients are normally determined at a stationary flow test bench, separately for intake and exhaust side, in the absence of the piston. However, engine operation differs from this setup; i. a. the piston might interact with valve flow around scavenging top dead center, and instead of steady boundary conditions, valve flow is nearly always subjected to pressure pulsations, due to pressure wave reflections within the gas exchange ports. In this work the influences of piston position and flow pulsation on valve flow coefficients are investigated for different SI engine geometries by means of 3D CFD and measurements at an enhanced flow test bench.

As the late combustion phase in SI engines is of high importance for a further reduction of fuel consumption and especially emissions, the impacts of unburnt mass, located in a small volume with a relatively large surface near the wall and in the top land volume, is of high relevance throughout the range of operation. To investigate and quantify the respective interactions, a state of the art Mercedes-Benz single cylinder research SI-engine was equipped with extensive measurement technology. To detect the axial and radial temperature distribution, several surface thermocouples were applied in two layers around the top land volume. As an additional reference, multiple surface thermocouples in the cylinder head complement the highly dynamic temperature measurements in the boundary zones of the combustion chamber.

Engine Knock is a stochastic phenomenon that occurs during the regular combustion of spark ignition (SI) engines and limits its efficiency. Knock is triggered by an autoignition of local “hot spots” in the unburned zone, ahead of the flame front. Regarding chemical kinetics, the temperature and pressure history as well as the knock resistance of the fuel are the main driver for the autoignition process. In this paper, a new knock modeling approach for natural gas blends is presented. It is based on a kinetic fit for the ignition delay times that has been derived from chemical kinetics simulations. The knock model is coupled with an enhanced burn rate model that was modified for Methane-based fuels. The two newly developed models are incorporated in a predictive 0D/1D simulation tool that provides a cost-effective method for the development of natural gas powered SI engines.

In the quasi-dimensional modeling of the spark-ignition combustion process, the burn rate calculation depends, among other influences, on the laminar flame speed. Commonly used models of laminar flame speeds are usually developed on the basis of measurement data limited to boundary conditions outside of the engine operation range. This limitation is caused by flame instabilities and forces flame speed models to be extrapolated for the application in combustion process simulation. However, for the investigation of, for example, lean burn engine concepts, reliable flame speed values are needed to improve the quality and predictive ability of burn rate models. For this purpose, a reference fuel for gasoline is defined to perform reaction kinetics calculations of laminar flame speeds for a wide range of boundary conditions.

In order to meet increasingly stringent exhaust emission regulations, new engine concepts need to be developed. Lean combustion systems for stationary running large gas engines can reduce raw NOx-emissions to a very low level and enable the compliance with the exhaust emission standards without using a cost-intensive SCR-aftertreatment system. Experimental investigations in the past have already confirmed that a strong reduction of the charge air temperature even below ambient conditions by using an absorption chiller can significantly reduce NOx emissions. However, test bench operation of large gas engines is costly and time-consuming. To increase the efficiency of the engine development process, the possibility to use 0D/1D engine simulation prior to test bench studies of new concepts is investigated using the example of low temperature charge air cooling. In this context, a reliable prediction of engine efficiency and NOx-emissions is important.

On the way to emission-free mobility, future fuels must be CO2 neutral. To achieve this, synthetic fuels are being developed. In order to better assess the effects of the new fuels on the engine process, simulation models are being developed that reproduce the chemical and physical properties of these fuels. In this paper, the fuel DMC+ is examined. DMC+ (a mixture of dimethyl carbonate (DMC) and methyl formate (MeFo) mainly, characterized by the lack of C-C Bonds and high oxygen content) offers advantages with regard to evaporation heat, demand of oxygen and knock resistance. Furthermore, its combustion is almost particle free. With the aid of modern 0D/1D simulation methods, an assessment of the potential of DMC+ can be made. It is shown that the simulative conversion of a state-of-the-art gasoline engine to DMC+ fuel offers advantages in terms of efficiency in many operating points even if the engine design is not altered.

The hybrid power train technology offers various prospects to optimize the engine efficiency in order to minimize the CO₂ emissions of an internal-combustion-engine-powered vehicle. Today different types of hybrid architectures like parallel, serial, power split or through-the-road concepts are commonly known. To achieve lowest fuel consumption the following hybrid electric vehicle drive modes can be used: Start/Stop, pure electric/thermal driving, recuperation of brake energy and the hybrid mode. The high complexity of the interaction between those power sources requires an extensive investigation to determine the optimal configuration of a natural-gas-powered SI engine within a parallel hybrid power train. Therefore, a turbocharged 1.0-liter 3-cylinder CNG engine was analyzed on the test bench. Using an optimized combustion strategy, the engine was operated at stoichiometric and lean air/fuel ratio applying both high- and low-pressure EGR.

CNG direct injection is a promising technology to promote the acceptance of natural gas engines. Among the beneficial properties of CNG, like reduced pollutants and CO2 emissions, the direct injection contributes to a higher volumetric efficiency and thus to a better driveability, one of the most limiting drawbacks of today’s CNG vehicles. But such a combustion concept increases the demands on the injection system and mixture formation. Among other things it requires a much higher flow rate at low injection pressure. This can be only provided by an outward-opening nozzle due to its large cross-section. Nevertheless its hollow cone jet with a specific propagation behavior leads to an adverse fuel-air distribution especially at higher loads under scavenging conditions. This paper covers numerical and experimental analysis of CNG direct injection to understand its mixture formation.

The introduction of CO₂-reduction technologies like Start-Stop or the Hybrid-Powertrain and the future emissions limits require a detailed optimization of the engine start-up. The combustion concept development as well as the calibration of the ECU makes an explicit thermodynamic analysis of the combustion process during the start-up necessary. Initially, the well-known thermodynamic analysis of in-cylinder pressure at stationary condition was transmitted to the highly non-stationary engine start-up. There, the current models for calculation of the transient wall heat fluxes were found to be misleading. But with a fraction of nearly 45% of the burned fuel energy, the wall heat is very important for the calculation of energy balance and for the combustion process analysis.

As engine knock limits the efficiency of spark ignition engines and consequently further reduction of CO2 emissions, SI engines are typically designed to operate at the knock boundary. Therefore, a precise knock model is necessary to consider this phenomenon in an engine process simulation. The basis of the introduced 0D/1D knock model is to predict when the unburnt mixture auto-ignites, since auto-ignitions precede knocking events. The knock model further needs to evaluate the auto-ignition, because not every auto-ignition results in engine knock. As the introduced model’s prediction of the auto-ignition onset is already validated at extensive variations of operating conditions, this publication focusses on its evaluation. For this, two new, independent criteria are developed that take the pre-reactions of the unburnt mixture before the start of combustion into account to calculate a respective threshold for the auto-ignition onset at the knock boundary.

Engine knock is limiting the efficiency of spark ignition engines and consequently further reduction of CO2 emissions. Thus, an combustion process simulation needs a well working knock model to take this phenomenon into account. As knocking events result from auto-ignitions, the basis of a knock model is the accurate modeling of the latter. For this, the introduced 0D/1D knock model calculates the Livengood-Wu integral to estimate the state of the pre-reactions of the unburnt mixture and considers the two-stage auto-ignition of gasoline fuels, which occurs at specific boundary conditions. The model presented in this publication is validated against measurement data of a single cylinder engine. For this purpose, more than 12 000 knocking working cycles are investigated, covering extensively varied operating conditions for a wide-ranging validation.

Pilot injection gas engines are commonly used as large stationary engines. Often, the combustion is implemented as a dual-fuel strategy, which allows both mixed and diesel-only operation, based on a diesel engine architecture. The current research project focuses on the application of pilot injection in an engine based on gasoline components of the passenger car segment, which are more cost-effective than diesel components. The investigated strategy does not aim for a diesel-only combustion, hence only small liquid quantities are used for the main purpose of providing a strong, reliable ignition source for the natural gas charge. This approach is mainly driven to provide a reliable alternative to the high spark ignition energies required for high cylinder charge densities. When using such small liquid quantities, a standard common-rail diesel nozzle will apparently not be ideal regarding some general specifications.

In this research, simulation and experimental investigation of H2 emission formation and its influence during the post-oxidation phenomenon were conducted on a turbo-charged spark ignition engine. During the post-oxidation phenomenon phase, rich air-fuel ratio (A/F) is used inside the cylinder. This rich excursion gives rise to the production of H2 emission by various reactions inside the cylinder. It is expected that the generation of this H2 emission can play a key role in the actuation of the post-oxidation and its reaction rate if enough temperature and mixing strength are attained. It is predicted that when rich combustion inside the cylinder will take place, more carbon monoxide (CO)/ Total Hydro Carbon (THC)/ Hydrogen (H2) contents will arrive in the exhaust manifold. This H2 content facilitates in the production of OH radical which contributes to the post-oxidation reaction and in-turn can aid towards increasing the enthalpy.

The engine development process has been enhanced significantly by virtual engineering methods during the last decades. In terms of in-cylinder flow field, charge flow and combustion modelling, 3D-CFD (three dimensional) simulations enable detailed analysis and extended investigations in order to gain additional knowledge about design parameters. However, the computational time of the 3D-CFD is an obvious drawback that prevents a reasonable application for extensive analysis with varying speed, load and transient conditions. State-of-the-art 0D (zero dimensional) approaches close the gap between the demand of high computational efficiency and a satisfying accordance with experimental data. Recent improvements of phenomenological combustion approaches for gasoline spark ignition engines deal with the consideration of detailed flow parameters, the accuracy of the laminar flame speed calculation and the prediction of the knock limit.

Since 0D/1D-simulations of natural gas spark ignition engines use model theories similar to gasoline engines, the impact of changing fuel characteristics needs to be taken into consideration in order to obtain results of higher quality. For this goal, this paper proposes some approaches that consider the influence of binary fuel mixtures such as methane with up to 40 mol-% of ethane, propane, n-butane or hydrogen on laminar flame speed and knock behavior. To quantify these influences, reaction kinetics calculations are carried out in a wide range of the engine operation conditions. Obtained results are used to update and extend existing sub-models. The model quality is validated by comparing measured burn rates with simulation results. The benefit of the new sub-models are utilized by predicting the influence the fuel takes on engine operating limits in terms of knocking and lean misfire limits, the latter being determined by using a cycle-to-cycle variation model.

Compact and computationally efficient reaction models capable of accurately predicting ignition delay and heat release rates are a prerequisite for the development of strategies to control and optimize HCCI engines. In particular for full boiling range fuels exhibiting two-stage ignition a tremendous demand exists in the engine development community. To this end, in a previous investigation, a global reaction mechanism was developed and fitted to data from shock tube experiments for n-heptane and five full boiling range fuels. By means of a genetic algorithm, for each of these fuels, a set of reaction rate parameters (consisting of pre-exponential factors, activation energies and concentration exponents) has been defined, without any change to the model form.

As a promising concept to improve fuel efficiency of a long-haul heavy duty truck with diesel engine, organic Rankine cycle (ORC) based waste heat recovery system (WHR) by utilizing the exhaust gas from internal combustion engine has continuously drawn attention from industry in recent years. The greatest achievable global efficiency may be, however, restricted by the engine. On one hand, engine operating conditions have direct impact on the temperature and the mass flow of exhaust gas, which is the waste heat source, on the other hand, the engine cooling system limits the heat rejection from the condenser of the WHR system. This paper aims to evaluate the impacts of the varied engine applications considering the effects of the WHR system on the global efficiency and engine emissions.

Knocking is one of today’s main limitations in the ongoing efforts to increase efficiency and reduce emissions of spark-ignition engines. Especially for synthetic fuels or any alternative fuel type in general with a much steeper increase of the knock frequency at the KLSA, such as hydrogen, precise knock prediction is crucial to exploit their full potential. This paper therefore proposes a post-processing tool enabling further investigations to continuously gain better understanding of the knocking phenomenon. In this context, evaluation of local auto-ignitions preceding knock is crucial to improve knowledge about the stochastic occurrence of knock but also identify critical engine design to further optimize the geometry. In contrast to 0D simulations, 3D CFD simulations provide the possibility to investigate local parameters in the cylinder during the combustion.

To meet the requirements of strict CO2 emission regulations in the future, internal combustion engines must have excellent efficiencies for a wide operating range. In order to achieve this goal, various technologies must be applied. Additionally, fuels other than gasoline should also be considered. In order to investigate the potential of the efficiency improvement, a SI engine was designed and optimized using 0D/1D methods. Some of the advanced features of this engine model include: High stroke-to-bore-ratio, variable valve timings with Miller cycle, EGR, cylinder deactivation, high turbulence concept, variable compression ratio and extreme downsizing. The fuel of choice was gasoline. With the proper application of technologies, the fuel consumption at the most relevant operating window could be decreased by approximately 10% in comparison to a state-of-the-art spark-ignited direct-injection four-cylinder passenger car engine.