Search Results

Despite the many years of widespread use of the BMW Intake Valve Deposit (IVD) vehicle test, relatively little has been published quantifying the variation in the test procedure. This paper presents an analysis of the variability in the BMW test. Though results from 8045 km (8K; 5,000 mile) tests rather than 16090 km (16K; 10,000 mile) are highlighted due to the size of the available database and relative sensitivity of the data, analysis suggests that variation at 8K is representative of 16K variation. A square root transformation of average deposit weight at 8K, though more cumbersome than the more common log transformation, is found to be the most appropriate way to eliminate the dependence of variation on the absolute level of deposits. Within-car variation is found to account for over half of the test-to-test variation, contradicting the notion that car-to-car differences are the dominant source of variability.

The objective of this investigation is to verify and characterize the influence of fuel volatility on maximum liquid-phase fuel penetration for a variety of actual Diesel fuels under realistic Diesel engine operating conditions. To do so, liquid-phase fuel penetration was measured for a total of eight Diesel fuels using laser elastic-scatter imaging. The experiments were carried out in an optically accessible Diesel engine of the “heavy-duty” size class at a representative medium speed (1200 rpm) operating condition. In addition to liquid-phase fuel penetration, ignition delay was assessed for each fuel based on pressure-derived apparent heat release rate and needle lift data. For all fuels examined, it was observed that initially the liquid fuel penetrates almost linearly with increasing crank angle until reaching a maximum characteristic length. Beyond this characteristic length, the fuel is entirely vapor phase and not just smaller fuel droplets.

Recently, research and testing of oxygenated diesel fuels has increased, particularly in the area of exhaust emissions. Included among the oxygenated diesel fuels are blends of diesel fuel with ethanol, or E diesel fuels. Exhaust emissions testing of E diesel fuel has been conducted by a variety of test laboratories under various conditions of engine type and operating conditions. This work reviews the existing public data from previous exhaust emissions testing on E diesel fuel and includes new testing performed in engines of varied design. Emissions data compares E diesel fuel with normal diesel fuel under conditions of different engine speeds, different engine loads and different engine designs. Variations in performance under these various conditions are observed and discussed with some potential explanations suggested.

This paper features the results of emission tests conducted on diesel oxidation catalysts, and the combination of diesel oxidation catalysts and water blend fuel (diesel fuel continuous emulsion). Vehicle chassis emission tests were conducted using an urban bus. The paper reviews the impact and potential benefits of combining catalyst and water blend diesel fuel technologies to reduce exhaust emissions from diesel engines.

In response to industry demands for a method to qualify fuels for their intake valve deposit (IVD) forming tendencies, the Coordinating Research Council (CRC) has developed an engine dynamometer test procedure. In Phase I, the 2.3L Ford engine was chosen as the focus test engine in comparison testing with two other high volume U.S. manufactured engines.1* A two-mode dynamometer test was developed in Phases II-A & II-B and shown to discriminate among the test fuels at a 95% confidence level.2 In Phase III, both an interlaboratory study (ILS) of the two-mode dynamometer test and a vehicle fleet study were performed. The ILS was conducted to determine the repeatability and reproducibility of the test procedure and also to fulfill requirements for consideration of the test as an American Society for Testing and Materials (ASTM) standard.

A new gas phase kinetic model using Westbrook's gas phase n-heptane model and Frenklach's soot model was constructed. This model was then used to predict the impact on PAH formation as an indices of soot formation on ethanol/diesel fuel blends. The results were then compared to soot levels measured by various researchers. The ignition delay characteristics of ethanol were validated against experimental results in the literature. In this paper the results of the model and the comparison with experimental results will be discussed along with implications on the method of incorporation of additives and alternative fuels.

Today's high technology engines are designed with fast-burn combustion chambers, swirl-generated intake ports, and improved intake manifold designs to achieve high specific power output, improved fuel economy and lower exhaust emissions. Consequently, the engine performance is greatly affected by deposit build up in these critical areas. Deposits may result in cold-start driveability problems, degradation of fuel economy, loss of power, and increase in NOx emissions. Most gasoline marketers have added polymeric additives to control deposits, though these additives have caused Octane Requirement Increase (ORI) higher than normal. Recently, a new type of chemistry has been developed to control induction system deposits and reduced octane requirement increase.