Search Results

Standard

Thrust Washers – Design and Application

2011-06-13

CURRENT

J924_201106

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

TURBOCHARGER NOMENCLATURE AND TERMINOLOGY

1979-11-01

HISTORICAL

J922_197911

This recommended practice applies to nomenclature of turbo-charger parts and terminology of performance. Modifying adjectives are omitted in some cases for the sake of simplicity. However, it is considered good practice to use such adjectives when they add to clarity and understanding.

Standard

THRUST WASHERS—DESIGN AND APPLICATION

1995-02-01

HISTORICAL

J924_199502

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

THRUST WASHERS—DESIGN AND APPLICATION

1981-01-01

HISTORICAL

J924_198101

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

Spring-Loaded Clutch Spin Test Procedure

2012-10-23

CURRENT

J1073_201210

This SAE Recommended Practice applies to spring-loaded clutches such as are used with manual shift type transmissions.

Standard

Split Type Bushings – Design and Application

2011-06-13

CURRENT

J835_201106

This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques, and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.

Standard

Sleeve Type Half Bearings

2011-06-10

CURRENT

J506_201106

This SAE Standard defines the normal dimensions, dimensioning practice, tolerances, specialized measurement techniques, and glossary of terms for bearing inserts commonly used in reciprocating machinery. The standard sizes cover a range which permits a designer to employ, in proper proportion, the durability and lubrication requirements of each application, while utilizing the forming and machining practices common in manufacture of sleeve type half bearings. Not included are considerations of hydrodynamic lubrication analysis or mechanical stress factors of associated machine structural parts which determine the nominal sizes to be used, selection of bearing material as related to load carrying capacity, and economics of manufacture. For information concerning materials, see SAE J459 and SAE J460. These suggested sizes provide guidelines which may result in minimal costs of tooling but do not necessarily represent items which can be ordered from stock.

Standard

Seals—Evaluation of Elastohydrodynamic

2000-10-09

HISTORICAL

J1002_200010

This SAE Information Report is a review of test methods that have been used to evaluate elastomeric hydrodynamic seals. The advantages and disadvantages of each method are discussed. There are ten methods total which include three suggested methods. For those interested in more detailed information on hydrodynamic sealing systems, see 2.2.

Standard

SPLIT TYPE BUSHINGS—DESIGN AND APPLICATION

1995-02-01

HISTORICAL

J835_199502

This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques, and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.

Standard

SPLIT TYPE BUSHINGS - DESIGN AND APPLICATION

1981-12-01

HISTORICAL

J835_198112

This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.

Standard

SPARK ARRESTER TEST PROCEDURE FOR MEDIUM SIZE ENGINES

1991-01-01

HISTORICAL

J350_199101

This SAE Recommended Practice establishes equipment and procedures for testing spark arresters used on medium-size, single-position internal combustion engines, normally used in transportable, stationary, and vehicular applications, such as highway trucks, agricultural tractors, industrial tractors, other mobile equipment, and motorcycles. This document provides two methods of testing (laboratory testing and engine testing) which may be used to evaluate a spark arrester. It also includes special requirements for screen type devices and an endurance test procedure for screen type spark arresters.

Standard

SEALS—APPLICATION GUIDE TO RADIAL LIP

1979-04-01

HISTORICAL

J946D_197904

Standard

SEALS: APPLICATION GUIDE TO RADIAL LIP

1988-06-01

HISTORICAL

J946_198806

Standard

SEALS: APPLICATION GUIDE TO RADIAL LIP

1987-02-01

HISTORICAL

J946_198702

Standard

SEALS - EVALUATION OF ELASTOHYDRODYNAMIC

1987-06-01

HISTORICAL

J1002_198706

Standard

Radial Lip Seal Torque—Measurement Method and Results

2000-10-02

HISTORICAL

J1971_200010

This SAE Recommended Practice provides information on procedures, tools, and fixtures useful in determining frictional torque measurement of radial lip oil seals. Information on the effect of various operational environments on oil seals are discussed and a means of calculation of power consumption of seals is provided.

Standard

REPORTING ON EMISSION TESTING FOR IN-USE LIGHT-DUTY TRUCKS AND PASSENGER VEHICLES

2000-10-01

HISTORICAL

J1712_200010

This SAE Recommended Practice applies to the reporting of laboratory and test site data from the gaseous and evaporative emission tests of in-use light-duty trucks and passenger vehicles. This document describes the reporting of procedures, fuel specifications, and vehicle information necessary to compare the results of in-use tests. Any variations in vehicles, instrumentation, test equipment, or test program purpose should be adequately described.

Standard

RADIAL LIP SEAL TORQUE: MEASUREMENT METHODS AND RESULTS

1989-06-01

HISTORICAL

J1971_198906

Standard

Overcenter Clutch Spin Test Procedure

2012-10-23

CURRENT

J1079_201210

This SAE Recommended Practice applies to driving ring type overcenter clutches such as are used in industrial power takeoffs.

Standard

O.D. Coatings for Radial Lip-Type Shaft Seals

2002-10-25

CURRENT

J1947_200210

This SAE Information Report covers thin coatings of resinous based materials that can be placed on the metallic outer diameter of radial lip-type shaft seals to provide sealing when the mating bore finish is too rough to insure a proper seal (typically when finish exceeds 2.54 µm Ra, or in pressurized applications.) The coatings will have the following characteristics: a. Material shall dry to a tough, flexible, and non-tacky film. b. Thickness typically ranges from 0.005 to 0.076 mm. c. It shall not crack, flake, or powder when scraped. d. Coating shall adhere to seal case as noted in text. e. The sealer shall not show any evidence of peeling, blistering, softening, or dissolution when tested in media to be sealed.