Search Results

Encapsulations of E-drive systems are gaining importance in electric mobility, since they are simple measure to improve the noise behavior of the drive. Current experimental evaluation methods however pose substantial challenges for the test personnel and are associated with considerable effort in both time and cost. Evaluating the encapsulation on an e-drive test bed, for example, requires a functional e-drive and test bed resources. Evaluations in the vehicle on the other hand make objective assessments difficult and are subject to increasingly limited availability of prototype vehicles fit for NVH testing. To overcome these challenges, AVL has developed a new experimental evaluation method for the NVH efficiency of e-drive encapsulations. In this method, the e-drive is freely suspended in a semi-anechoic chamber and its structure is excited using shakers while the radiated noise with and without encapsulation is measured.

The emission behaviour of an internal combustion engine under test-bed conditions shows differences to the emission behaviour under real in-use conditions. Because of this fact, the developers of combustion engines and the legislator are focussing on the measurement and optimization of real in-use emissions. To this day, the research, the adjustment of the carburettor and the legislation of small handheld engines is performed under test bench conditions, especially conditioned fuel pressure and temperature, as well as air temperature. Also the engines are laid out for two operation points: rated speed with full open throttle and idle speed. This test-procedure is used for all kinds of handheld off-road applications and does not consider the load profile of the different power tools. Especially applications with transient load profiles, for example chainsaws, work in more than two operating points in real use.

The NVH character of any car is highly dependent on its operating condition. With BEVs, it depends strongly on the driving speed, total torque, temperature and state of charge of the battery. For these reasons, OEMs usually want to measure many run-ups with constant torque steps or constant driving speed. The supposed simplification of the powertrain by the transition to electrified drive components and the elimination of auxiliary units poses new challenges for acoustic engineers. Unlike traditional vehicles with internal combustion engines, noise components of electric drivetrains fall into a range of audibility where the human ear reacts particularly sensitively. During a 3-year cooperation with a big OEM most of the premium BEVs on the German market were measured and benchmarked to get a feedback about their NVH performance. In addition, the desire for objective characteristic values arose.

Meeting future legislative targets for SI engines by means of low cost technologies is a big challenge for engineers. Despite the use of simple and cost efficient components these engines have to fulfill customer requirements in terms of power and fuel economy, representing the most important selling arguments. Without the possibility of integrating modern technologies like fuel injection systems for mixture preparation instead of simple carburetors, it is very complex to find viable solutions that enable the achievement of these targets. A main key to improve emission behavior, fuel economy and performance on carbureted engines is to get an insight in the mixture preparation process, especially under transient conditions.

Unstable combustion and high cyclic variations of the in-cylinder pressure associated with low engine running smoothness and high emissions are mainly caused by cyclic variations of the fresh charge composition, the variability of the ignition and the fuel mass. These parameters affect the inflammation, the burn rate and thus the whole combustion process. In this paper, the effects of fluctuating fuel mass on the combustion behavior are shown. Small two-stroke engines require special measuring and testing equipment, especially for measuring the fuel consumption at very low fuel flow rates as well as very low fuel supply pressures. To realize a cycle-resolved measurement of the injected fuel mass, fuel consumption measurement with high resolution and high dynamic response is not enough for this application.

Today's sophisticated state-of-the-art powertrains with various intelligent control units (xCU) need to be calibrated and tested stand-alone as well as in interaction. Today the majority of this work is still carried out with prototype vehicles on test tracks. Moving prototype vehicle tests from the road into the lab is key in achieving shorter development times and saving development cost. This kind of frontloading requires a modular and powerful simulation of all vehicle components, test track, and driver in steady state and dynamic operation. The described HIL (Hardware In the Loop) high performance driveline dyno test bed uses driveline components and models from the engine all the way to the wheel ends. The test cell was built to do real time vehicle maneuvers and NVH testing. This test setup can emulate any road surface and grade and vehicle inertia including wheels and engine as close to reality as possible.

Synchronizers are shifting elements in transmissions with power interruption, such as manual transmissions (MT) and automated manual transmissions (AMT). Synchronizers are also used in dual clutch transmissions (DCT) for shifting the preselected idler gear in the load-free branch of the transmission. Electric drive units (EDU) mainly consist of a two-stage transmission combined with a high-speed electric motor. Synchronizers realize the power flow from an idler gear to a gear shaft of the transmission. Automotive transmissions are usually operated with lubricating oils in order to minimize friction and wear of the mechanical components. Lubricating oil has a major influence on torque losses and on vibration behavior of transmission components. Torsional vibrations of mechanical components in transmissions lead to natural vibrations with high impact forces and thus to high radiated airborne sound levels.