Search Results

This laboratory presents a new step-automatic transmission fluid with enhanced friction durability and robustness for the Asian marketplace. This mineral-oil-based fluid also meets JASO M315-1A performance requirements on torque capacity, anti-oxidation, anti-wear, extreme pressure (EP), anti-aeration/foam control, copper corrosion and anti-rust performance. The fluid offers a JASO M349 low velocity friction apparatus (LVFA) durability lifetime of over 1100 hours. Moreover, this fluid maintains stable torque capacity during its entire LVFA durability lifetime, across the temperature range of 40 to 120 °C. Similarly, friction level changes with sliding speed are smaller than experienced by other commercial factory-fill ATFs. These critical performance features are due to a new fluid friction system approach, which may enable new types of transmission hardware or calibration.

This paper presents the results of a three city survey designed to determine the relative frequency of illumination of vehicle on-board diagnostic (OBD) malfunction indicator lights (MIL) on 2001 and later model year vehicles. The survey was conducted in a Canadian market, Regina, and two U.S. markets, Minneapolis and Denver, to assess claims that the presence of methycyclopentadienyl manganese tricarbonyl (MMT®) in gasoline causes the failure of technology necessary to meet stringent Tier 2 emission standards applicable in North America. The results of the survey do not support the claim that MMT® is incompatible with the effective functioning of the advanced vehicle emission technology necessary to meet Tier 2 emission standards. The results substantiate that the performance of the most advanced vehicles operating on gasoline containing MMT® is not materially different from the performance of comparable vehicles operating on gasoline that does not contain MMT®.

This paper presents data on the effect of ATF additives on lead corrosion as measured in a simple bench test and the MERCON® ABOT. The correlation between the bench test and the ABOT test will be discussed. The effect of base oil, carboxylic acids, and oxidation products on lead corrosion will also be discussed. Two types of additives used in automatic transmission fluids can reduce lead corrosion. Each additive has shown a statistically significant linear correlation to lead loss. There is also a statistically significant detrimental interaction between the additives when both are present in the fluid simultaneously. A mechanism to explain this interaction will be presented along with analyses of the lead surfaces after ABOT testing.

Multiple plate disk clutches are used extensively for shifting gears in automatic transmissions. In a shift from one gear to another one or more clutches is engaging or disengaging. In these active clutches the automatic transmission fluid (ATF) and friction material experience large changes in pressure P, temperature T, and sliding speed v. The coefficient of friction, μ, of the ATF and friction material depends on v, P and T, and also changes during clutch engagement. Changes in μ can lead to vibration and poor shift quality if the ATF and clutch friction material are improperly selected. An in-depth theoretical understanding of the cause of vibration in shifting clutches is crucial in the development of a suitable ATF to work with a particular friction material.

There has been a global technology convergence by engine manufacturers as they strive to meet or exceed the ever-increasing fuel economy mandates that are intended to mitigate the trend in global warming associated with CO2 emissions. While turbocharging and direct-injection gasoline technologies are not new, when combined they create the opportunity for substantial increase in power output at lower engine speeds. Higher output at lower engine speeds is inherently more efficient, and this leads engine designers in the direction of overall smaller engines. Lubricants optimized for older engines may not have the expected level of durability with more operating time being spent at higher specific output levels. Additionally, a phenomenon that is called low-speed pre-ignition has become more prevalent with these engines.

This report describes the results of a fleet test conducted with vehicles certified to Euro IV standards and equipped with high cell density close coupled manifold mounted catalysts. The purpose of the test was to determine the effect of MMT® on vehicle emission system durability under severe in-service operating conditions and to address vehicle manufacturers concerns about the effects of MMT® in advanced technology vehicles. The results clearly show that performance and durability of the vehicles are not affected even under severe operating conditions when MMT® is used in the gasoline. Two pairs each of Volkswagen Passats and Opel Corsas (eight vehicles total) were operated on a base fuel and a base fuel splash blended with MMT® at a concentration of 18 milligrams manganese per liter (“mg Mn/l”). The vehicles accumulated mileage on a driving regime representative of severe service.

This paper provides an overview of driveline fluids, in particular automatic transmission fluids (ATFs), and is intended to be a general reference for those working with such fluids. Included are an introduction to driveline fluids, highlighting what sets them apart from other lubricants, a history of ATF development, a description of key physical ATF properties and a comparison of ATF fluid specifications. Also included are descriptions of the chemical composition of such fluids and the commonly used basestocks. A section is included on how to evaluate used driveline oils, describing common test methods and some comments on interpreting the test results. Finally the future direction of driveline fluid development is discussed. A glossary of terms is included at the end.

Biodiesel fuel is a promising new renewable, alternate fuel source. However, its effect on diesel engine oil lubrication is largely untested at present. There is some indication that the use of biodiesel fuel can degrade diesel engine oil performance to such an extent that shortening of oil drain intervals is required. Oil which is fuel-diluted with biodiesel, which is known to contain unsaturated hydrocarbon bonds, would be expected to be more prone to oxidation. Current diesel engines designed to meet environmental standards tend to introduce more soot into the crankcase oil. The new diesel engine oils for use with biodiesel fuel must be capable of dispersing soot to minimize soot-induced viscosity increase of the oil and prevent engine wear. Oils will also need improved oxidation and corrosion inhibition. To examine soot-handling, ASTM D 7156 Mack T-11 engine test results with 20 wt% soy methyl ester in ultra-low sulfur diesel fuel (B20) were employed.

In the next ILSAC passenger car motor oil specification the Sequence IIIG engine test, as well as two versions of the Thermo-Oxidation Engine Oil Simulation Test (TEOST) have been proposed as tests to determine the ability of crankcase oils to control engine deposits. The Sequence IIIG engine test and the TEOST MHT test are designed to assess the ability of lubricants to control piston deposits and the TEOST 33 test is designed to assess the ability of lubricants to control turbocharger deposits. We have previously characterized the chemical composition of Sequence IIIG piston deposits using thermogravimetric, infrared and SEM/EDS analyses. Sequence IIIG piston deposits contain a significant amount of carbonaceous material and the carbonaceous material is more prevalent on sections of the pistons that should encounter higher temperatures. Furthermore, the carbonaceous material appears to be a deposit formed by the Sequence IIIG fuel.

When gasoline-fueled vehicles are operated in consumer service, the oil used to lubricate the engine plays a key role in engine cooling, reducing friction, maintaining efficient operation, and optimizing fuel economy. The effects of normal vehicle operation on oil deterioration have a direct impact on fuel consumption. The authors have observed substantial differences between the deterioration of engine oil and resulting fuel economy under real-world driving conditions, and the deterioration of oils and resulting fuel economy in the standard laboratory test used to assess fuel economy in North America, the Sequence VID engine test (ASTM D7589). By analyzing the data from vehicles and comparing these data to the Sequence VID the authors have proposed and evaluated several changes to the Sequence VID test that improve the correlation with real-world operation and improve test discrimination.

This report focuses on an extended investigation of the durability of Dual Clutch Transmission (DCT) fluids. The performance requirements of DCT fluids differ from those of traditional step automatic transmission fluids. For that reason, key performance lab tests are discussed in this paper. Friction durability is measured with a modified version of the JASO M348 SAE#2 friction plate test. In addition, results from a vehicle chassis dynamometer test are discussed. This test involves running a 2008 Volkswagen GTI for 60,000 dynamometer miles (42,000 cycles) of severe acceleration and high speed conditions. Finally, a new DCT fluid, which performs well in these tests, offers friction stability and superior wear protection of transmission hardware, when compared to the commercial reference fluid.

Improving vehicle fuel efficiency is a key market driver in the automotive industry. Typically lubricant chemists focus on reducing viscosity and friction to reduce parasitic energy losses in order to improve automotive fuel efficiency. However, in a transmission other factors may be more important. If an engine can operate at high torque levels the conversion of chemical energy in the fuel to mechanical energy is dramatically increased. However high torque levels in transmissions may cause NVH to occur. The proper combination of friction material and fluid can be used to address this issue. Friction in clutches is controlled by asperity friction and hydrodynamic friction. Asperity friction can be controlled with friction modifiers in the ATF. Hydrodynamic friction control is more complex because it involves the flow characteristics of friction materials and complex viscosity properties of the fluid.

A model and simulation results are presented for the torsional dynamics of a rear wheel driveline while the vehicle is coasting in a turn. The model includes the effects of road load and powertrain drag, limited slip differential clutch friction, the inertias of the vehicle, wheels, axles, differential carrier, and driveshaft, the final drive ratio, torsional stiffnesses of the axles and driveshaft, vehicle track width, and radius of the turn. The dynamics of coasting in a turn differ from powered driving due to changes in the inertia loading the driveshaft, the damping effect of the disengaged transmission, and nonlinearities in the clutch friction. Specific focus is given to vibration in the axles and driveshaft due to variations in the torque-speed slope of the clutches, which is determined by the slope of the friction coefficient ‘μ’ versus sliding speed ‘v’ in the limited slip clutches.

Mobile source emissions standards are becoming more stringent and particulate emissions from gasoline direct injection (GDI) engines represent a particular challenge. Gasoline particulate filter (GPF) is deemed as one possible technical solution for particulate emissions reduction. In this work, a study was conducted on eight formulations of lubricants to determine their effect on GDI engine particulate emissions and GPF performance. Accelerated ash loading tests were conducted on a 2.4L GDI engine with engine oil injection in gasoline fuel by 2%. The matrix of eight formulations was designed with changing levels of sulfated ash (SASH) level, Zinc dialkyldithiophosphates (ZDDP) level and detergent type. Comprehensive evaluations of particulates included mass, number, size distribution, composition, morphology and soot oxidation properties. GPF performance was assessed through filtration efficiency, back pressure and morphology.

Low speed pre-ignition (LSPI) is an undesirable combustion phenomenon that limits the fuel economy, drivability, emissions and durability performance of modern turbocharged engines. Because of the potential to catastrophically damage an engine after only a single pre-ignition event, the ability to reduce LSPI frequency has grown in importance over the last several years. This is evident in the significant increase in industry publications. It became apparent that certain engine oil components impact the frequency of LSPI events when evaluated in engine tests, notably calcium detergent, molybdenum and phosphorus. However, a close examination of the impact of other formulation additives is lacking. A systematic evaluation of the impact of the detergent package, including single-metal and bimetal detergent systems, ashless and ash-containing additives has been undertaken using a GM 2.0L Ecotec engine installed on a conventional engine dynamometer test stand.

Countries from every region in the world have set aggressive fuel economy targets to reduce greenhouse gas emissions. To meet these requirements, automakers are using combinations of technologies throughout the vehicle drivetrain to improve efficiency. One of the most efficient types of gasoline engine technologies is the turbocharged gasoline direct injection (TGDI) engine. The market share of TGDI engines within North America and globally has been steadily increasing since 2008. TGDI engines can operate at higher temperature and under higher loads. As a result, original equipment manufacturers (OEMs) have introduced additional engine tests to regional and OEM engine oil specifications to ensure performance of TGDI engines is maintained. One such engine test, the General Motors turbocharger coking (GMTC) test (originally referred to as the GM Turbo Charger Deposit Test), evaluates the potential of engine oil to protect turbochargers from deposit build-up.

There has been a trend in the automotive industry toward the use of lower viscosity engine oils as fuel economy requirements become more demanding across the globe. Lower viscosity fluids may improve fuel economy due to their improved pumpability, lower churning losses, and thinner lubricating films. However, there is one important caveat related to the use of these fluids: the amount of improvement, if any, is hardware design and application dependent. Standard industry fuel economy tests and engines with differing designs may show divergent responses when using lower viscosity engine oils, not always showing an improved fuel economy response. This paper summarizes the work conducted by the authors to demonstrate how and why the inconsistent results in fuel economy can occur with low viscosity oils.

Multiple plate disc clutches are used extensively for shifting gears in automatic transmissions. In the active clutches that engage or disengage during a shift the automatic transmission fluid (ATF) and friction material experience large changes in pressure, P, sliding speed, v, and temperature, T. The coefficient of friction, μ, of the ATF and friction material is a function of these variables so μ = μ(P,v,T) also changes during clutch engagement. These changes in friction coefficient can lead to noise or vibration if the ATF properties and clutch friction material are improperly matched. A theoretical understanding of what causes noise, vibration and harshness (NVH) in shifting clutches is valuable for the development of an ATF suitable for a particular friction material. Here we present a theoretical model that identifies the slope, ∂μ/∂T, of the coefficient of friction with respect to temperature as a major contributor to the damping in a clutch during engagement.

In-use vehicle regional inspection and maintenance (I/M) programs in the United States (US) and Canada generate a tremendous volume of data that provides a means for evaluating vehicle emissions compliance in actual consumer use. In this study, IM240 test data for several 1996 to 2001 vehicle models are analyzed from different regional programs in the US and Canada to confirm the suitability of using these data for evaluation of vehicles equipped with advanced emission control technology and to examine the various potential factors responsible for emissions noncompliance. Relative comparisons between US and Canadian program data are made for vehicle models used in the Alliance of Automobile Manufacturers (AAM) MMT® Test Program to examine the potential impact of differences in fuel properties on consumer experience and vehicle compliance.

Sliding contact between friction surfaces occurs in numerous torque transfer elements: torque converter clutches, shifting clutches, launch or starting clutches, limited slip differential clutches, and in the meshing of gear teeth under load. The total temperature in a friction interface is the sum of the equilibrium temperature with no sliding and a transient temperature rise, the flash temperature, caused by the work done while sliding. In a wet shifting clutch the equilibrium temperature is typically the bulk oil temperature and the flash temperature is the temperature rise during clutch engagement. The flash temperature is an important factor in the performance and durability of a clutch since it affects such things as the reactivity of the sliding surfaces and lubricant constituents (e.g., oxidation) and thermal stress in the components. Knowing how high the flash temperature becomes is valuable for the formulation of ATF, gear oil, engine oil and other lubricants.