Search Results

Electric Power Steering (EPS) needs to meet both functional and stability requirements, it plays significant role in controlling vehicle motion. In the meantime, customers emphasizes natural steering feel which can reflect vehicle motion and road surface information while isolate unwanted external disturbances. In general, conventional EPS control algorithms exert assist torque according to driver torque measured from torque sensor, while maintaining stability using stabilizing compensator. However, there exist significant trade-off between steering feel and stability, because the performances of assist torque control and stabilizing compensator are strongly coupled. In this paper a torque feedback control algorithm for EPS system is proposed in order to overcome the trade-off, and to achieve more natural, robust steering feel.

This paper proposes a modeling technique which is able to not only reliably and easily represent the hysteretic characteristics but also analyze the dynamic stress of a taper leaf spring. The flexible multi-body dynamic model of the taper leaf spring is developed by interfacing the finite element model and computation model of the taper leaf spring. Rigid dummy parts are attached at the places where a finite element leaf model is in contact with an adjacent one in order to apply contact model. Friction is defined in the contact model to represent the hysteretic phenomenon of the taper leaf spring. The test of the taper leaf spring is conducted for the validation of the reliability of the flexible multi-body dynamic model of the taper leaf spring developed in this paper. The test is started at an unloaded state with the excitation amplitude of 1∼2mm/sec and frequency of 132mm. First, the simulation is conducted with the same condition as the test.

Shudder vibration of a hydraulic power steering system during parking maneuver was studied with numerical and experimental methods. To quantify vibration performance of the system and recognize important stimuli for drivers, a shudder metric was derived by correlation between objective measurements and subjective ratings. A CAE model for steering wheel vibration analysis was developed and compared with measured data. In order to describe steering input dependency of shudder, a new dynamic friction modeling method, in which the magnitude of effective damping is determined by average velocity, was proposed. The developed model was validated using the measured steering wheel acceleration and the pressure change at inlet of the steering gear box. It was shown that the developed model successfully describes major modes by comparing the calculated FRF of the hydraulic system with measured one from the hydraulic excitation test.

In commercial vehicles, the exhaust brake assists the service brake to share the excess load and is used as an auxiliary brake to assist with the safety of the engine and the service brake on downhill slopes. To meet the customer's demand for auxiliary brakes, the specification of auxiliary brakes must be determined at the product proposal stage. In this study, performance design was conducted to derive exhaust brake specifications that fit the customer's requirements. For performance design, a system model was created and key design factors with high performance contribution were extracted. Optimal specifications were derived from parameter studies for key design factors. Additionally, performance analysis was performed with design tolerances using the performance design model. Performance was verified through actual vehicle evaluation and design specifications were confirmed.

The automotive industry’s journey towards fully autonomous vehicles brings more and more vehicle control systems. Additionally, the reliability and robustness of all these systems must be guaranteed for all road and weather conditions before release into the market. However, the ever-increasing number of such control systems, in combination with the number of road and weather conditions, makes it unfeasible to test all scenarios in real life. Thus, the performance and robustness of these systems needs to be proven virtually, via vehicle simulations. The key challenge for performing such a range of simulations is that the tire performance is significantly affected by the road/weather conditions. An end user must therefore have access to the corresponding tire models. The current solution is to test tires under all road surfaces and operating conditions and then derive a set of model parameters from measurements.

This paper presents the research related to the self-driving system that has been actively carried out recently. Previous studies have been limited to ensure the path following performance in linear and steady state-alike handling region with small lateral acceleration. However, in the high speed driving, the vehicle cornering response is extended to nonlinear region where tire grips are saturated. This requires a technology to create the driving path for minimum time maneuvering while grasping the tire grip limits of the vehicle in real time. The entire controller consists of three stages-hierarchy: The target motion is determined in the supervisor phase, and the target force to follow the target behavior is calculated in the upper stage controller. Finally, the lower stage controller calculates the actuator phase control input corresponding to the target force.

This paper proposes a simplified method to make the flux table considering the magnetic flux variation of the IPMSM (Interior Permanent Magnet Synchronous Machine) caused by temperature change in vehicle traction applications. Nowadays, normally an IPMSM with a rare-earth magnet is used for HEV traction applications. But because the flux density of the magnet varies with temperature, the optimal operating points, such as MTPA (Maximum Torque Per Ampere) and MTPV (Maximum Torque Per Voltage) of the motor drift according to temperature change. Those operating points can be expressed in a lookup table, that is, a flux table obtained by off-line experiment, which produces the DQ-axis current command with respect to the torque and flux reference. To reflect this temperature dependence in control, usually flux tables are generated at high, medium and low temperatures. Conventionally, all the three tables are constructed by experiment, which takes a great deal of time.

The method of Front End Auxiliary Drive (FEAD) system optimization can be divided into two ways. One is to use a mechanical device that decouples crank pulley from torsional vibration of crank shaft by using characteristics of spring. The other is to control belt tension through auto-tensioner in addition of alternator pulley device. Because the former case has more potential to reduce belt tension than the latter case, the development of mechanically decoupled crank pulley, despite of its difficulty of development, is getting popular among the industry. This paper characterizes latest crank pulley technologies, Crank Decoupler and Isolation Pulley, for torsional vibration reduction through functionality measurement result which composed of irregularity, slip, tensioner movement, belt span vibration, bearing hubload of idler and so on. Also it investigates their potential of belt tension reduction through steady state point fuel consumption test on dynamometer.

In order to utilize in-vehicle systems efficiently, many vehicles are becoming equipped with integrated controls near the center fascia or the control box. However, the placement of these control systems can cause safety issues and risks due to visual distractions. In this study, we proposed a new integrated touch screen on the steering wheel. For this experiment, a control system was placed on the steering wheel or the center fascia. 15 participants were required to drive while utilizing vent and navigation control tasks regarding four different locations. Three of these locations were based on the steering wheel (center, upper right, lower right) and one location on the center fascia. Afterwards, the task completion time and visual distraction rate of the different locations were measured and compared. The results showed that a touch screen placed on the upper right section of the steering wheel had better performance and lower user discomfort.

When two identical brakes are simultaneously tested on a vehicle chassis dynamometer, very often the left hand brake is found to squeal more or less than the right hand brake, all at different frequencies. This study was performed to develop some understanding of this puzzling phenomenon. It is found that as the wear rate difference between the inner pad and the outer pad increases, low frequency (caliper and knuckle) squeals occur more and more, and as the differential wear becomes larger and larger, high frequency (disc) squeals occur less and less, finally disappearing all together. Discs and calipers are found to affect the differential pad wear, in turn affecting brake squeal generation.

Suspension is a system which operates dynamically according to road condition unlike other system statically mounted to the body. Especially this is more remarkable in high performance vehicle because there are more high inputs from road to suspension than normal vehicle. For this reason, the tightening torque of suspension system of high performance vehicle is more important than other systems and normal vehicle. To support the clamping between parts against force from road when cornering, optimized tightening torque is required to maximize R&H performance. For this optimization, it should be conducted first to comprehend how much performance effects on vehicle by tightening torque. This paper presents relationship between tightening torque of suspension parts hardware and R&H performance.

This Study describes about the development of new concept' rear wheel guards for the reduction of Road Noise in the passenger vehicles. The new wheel guards are proposed by various frequency chamber concept and different textile layers concept. Two wheel guards were verified by small cabin resonance and vehicle tests. Through new developing process without vehicle test, Result of road noise will be expected if this concepts and materials of wheel guard are applied into automotive vehicle. As this concept consider tire radiation noise frequency and multilayers sound control multilayers, 2 concepts reduced road noise from 0.5 to 1.0dB. The proposed method of part reverberant absorption is similar to results of vehicle tests by part absorption index. Furthermore, optimization of frequency band in wheel guards will reduce more 0.5 dB noises. As a result of the application of Aimed Helmholtz and Multilayers concept, this paper classifies reduction of the road noise, cost and weights.

The engine indicated torque is not delivered entirely to the wheels, because it is lowered by losses, such as the pumping, mechanical friction and front auxiliary power consumption. The front auxiliary belt drive system is a big power consumer-fueling and operating the various accessory devices, such as air conditioning compressor, electric alternator, and power steering pump. The standard fuel economy test does not consider the auxiliary driving torque when it is activated during the actual driving condition and it is considered a five-cycle correction factor only. Therefore, research on improving the front end auxiliary drive (FEAD) system is still relevant in the immediate future, particularly regarding the air conditioning compressor and the electric alternator. An exertion to minimize the auxiliary loss is much smaller than the sustained effort required to reduce engine friction loss.

In the latest works [12], we presented the guideline for reducing Metal pick up(MPU, the main component of disc scoring) by controlling the location of the roughness of disc, the brake pad friction coefficients and the disc slot's size. In this study, the previously studied iron transfer theory to 'Cu free' brake pad and the disc surface roughness controlling methods which are based on the mass production manufacturing process are applied. It is possible to suggest the ways to improve the scoring-free disc without reducing friction coefficient between the disc and pad, and any demerit such as increased wear and airplane noise like conventional slot discs [11].

The effects of pad properties and thermal coning of discs on high speed judder were investigated using dynamometer and vehicle tests. The friction materials of different thermal conductivities were manufactured and the discs were design-modified to control the thermal coning during braking under high speed conditions. Brake Torque Variation(BTV) was measured to evaluate the judder propensity in the dynamometer tests and the vibration on steering wheel and brake pedal was measured in the vehicle tests. The results showed that the increase of thermal conductivity of pad could not affect the judder propensity during high speed braking below 350°C of disc temperature, however better disc design reduced judder propensity due to the lower thermal deformation. Moreover, the increase of pad compressibility can reduce judder propensity due to the increase of damping capacity.

EMB (Electro-Mechanical Brake) which converts electrical motor power to brake clamping force at each wheel is a system that has been investigated and developed by various automotive part suppliers through the years. In particular, as the number of electrically powered vehicles, such as hybrid electric vehicles, electric vehicles and fuel cell electric vehicles, has expanded, the EMB has received increased interest due to its fast response that is much suited for effective cooperative control with regenerative braking. However, issues such as cost competitiveness, reliability and regulations need to be solved for commercialization [1-2]. A new concept, the hybrid Electro-Mechanical Brake (hEMB) is characterized by a dual piston structure linked by hydraulics inside of the caliper. It is possible to reduce the required motor power and increase the level of emergency back-up braking through the amplification effect of the dual piston mechanism [3].

The development trend of new vehicles is to shorten the development period, diversify the models, and produce small amounts compared to the past. The current development process of braking systems is difficult to meet recent development trends, and it is more difficult to shorten the development period in the verification process that requires actual products. In this paper, we developed a 1-D Simulation of AMESim, MATLAB/Simulink Co-Simulation model of Hyundai Mobis iMEB(Integrated Mobis Electronic Brake) system for eco-friendly vehicles. If hydraulic braking is applied more than the tire grip force during braking, tire slip occurs, and if the rear wheel is locked before the front wheel, stability is lost, so it is advantageous to decide design parameter of brake system to make the front wheel first locked in consideration of design parameters of each vehicle.

Recently, as part of the effort to enhance fuel efficiency and reduce costs for eco-friendly vehicles, the R-gearless system has been implemented in the TMED (P)HEV system. Due to the removal of the reverse gear, a distinct backward driving method needs to be developed, allowing the Electronic Motor (e-Motor) system to facilitate backward movement in the TMED (P)HEV system. However, the capability of backward driving with the e-Motor is limited because of partial failure in the high-voltage system of an R-gearless system. Thus, we demonstrate that it is possible to improve backward driving problems by applying a new fail-safe strategy. In the event of a high-voltage battery system failure, backward driving can be achieved using the e-Motor with constant voltage control by the Hybrid Starter Generator (HSG), as proposed in this study.

This paper describes the optimal design process of the steering column system and the supporting system. At the initial concept stage of development process, a design guide is proposed to obtain sufficient stiffness of the steering system while reducing idle vibration sensitivity of the system. Case studies on resonance isolation are summarized, in which separated vibration modes among systems by applying Vibration Mode Map at the initial stage of design process. This study also makes it possible to provide design guideline for optimal dynamic damper system using CAE (computer aided engineering) analysis. The damper FE (finite element) model is added to vehicle model to analyze the relation between the frequency and the sensitivity of steering column system. This analysis methodology enables target performance achievement in early design stage and reduction of damper tuning activity after proto car test stage.

The high speed continuous braking distance assessment is the worst condition for thermal fades. This study was conducted to investigate the relationship between fade characteristic and friction materials & brake fluid amount for improving braking distance. So, we used the dynamometer to measure the friction coefficient, braking distance and required brake fluid amount. Through the measurements, the research was carried out as follows. First of all, we studied the influence of friction coefficient about different shapes (chamfer shape, area of the friction material, number of slots) on the same friction material. Secondly, we knew the effects of braking distance by the shape of the friction material. Through these two studies, the shape of the friction material favorable to the fade characteristics was derived. Finally, we measured the amount of required brake fluid in caliper after 10 consecutive braking cycles through Dynamometer.