Search Results

Due to the transformation of the automotive industry from conventional vehicles to electric vehicles, new challenges have emerged concerning Electromagnetic Compatibility. Though the Radiated Emission limits in global regulation are the same for both types of powertrains of vehicles, however, due to the phenomena of conversion of high voltage to low voltage, rapid charging/discharging, and different components involved in electric powertrain, the Radiated Emission from electric vehicles give a strikingly different trend which is challenging to combat. When compared with the conventional Spark Ignition vehicle, many other electronic components of the electric vehicle stay in the mode of Power ON while in the “Ignition ON” steady state. This resulted in us observing a significant shift in the amplitude and frequency throughout the frequency band of Radiated Emission measurement.

The death toll due to traffic accidents in India is on a rise, according to the latest Road Transport ministry report, a total of 4.97 lakh road accident was reported in 2011. Though compared to 2010, the accidents have gone down by 1,945, the number of deaths at 1,42,485 has increased by over 7,000.[1] This paper proposes a design of an Emergency Intimation System (EIS) tailored to fit for Indian consumer needs and available infrastructure. EIS is an emergency alert technology devised to assist drivers and passenger in an event of vehicle crash. Majority of deaths are caused by slow accident response time. EIS is aimed to lower this response time and ensure that the required rescue and medical services are made available in time. This device employed to make this emergency alerts will be fitted into the vehicle Electrical and Electronics (E/E) architecture and will have interfaces with crash sensor network, CAN network and GSM etc.

In year 2015, 17 people were killed every hour by road accidents in India [1]. The occurrence of road accidents is observed to be higher during night, when visibility is at its lowest. The two factors which affect visibility are insufficient illumination and glare caused by the oncoming traffic. The Adaptive Front Lighting System [AFS] is an active safety feature which addresses these problems by employing specific lighting modes for Town, Country, Expressway conditions and automatic switching between Driving Beam and Passing Beam whenever required. Matrix of LEDs or a Projector with an actuator or a combination of both is employed in achieving different Lighting modes. The projector based AFS module is preferred for implementing the AFS control logic for passing beam owing to its economic cost.

Ride is considered to be one of the crucial criterion for evaluating the performance of a vehicle. Automobile industry is striving for improvement in designs to provide superior passenger comfort in Commercial vehicles segment. In Industry, Quarter-car model has been used for years to study the vehicle’s ride dynamics. But due to lower DOF involved in quarter car, the output accuracy is somewhat compromised. This paper aims in development of a 7 DOF full-car Model to perform the ride- comfort analysis for Light Duty 4*2 Commercial Bus using MATLAB Simulink which can be used to tune the suspension design to meet the required ride-comfort criteria. Firstly, experimental data and Physical Parameters are collected by performing Practical Test on commercial Bus on different road profiles. Secondly, a Full Car Mathematical Model with 7 DOF has been developed for a bus using MATLAB Simulink R2018a.

This paper presents a methodology for predicting thermal comfort inside Midibus cabin with an objective to modify the Heating, Ventilation and Air Conditioning (HVAC) duct design and parametric optimization in order to have improved thermal comfort of occupant. For this purpose the bus cavity is extracted from baseline CAD model including fully seated manikins with various seating positions. Solar Load has been considered in the computational model and passenger heat load is considered as per BSR/ASHRAE 55-1992R standard. CFD simulation predicted the air temperature and velocity distribution inside passenger cabin of the baseline model. The experimental measurements have been carried out as per the guidelines set in APTA-BT-RP-003-07 standard. The results obtained from CFD and Experimental test were analysed as per EVS EN ISO7730 standard and calculated occupant comfort in terms of thermal comfort parameters like Predicted Mean Vote (PMV) and Predicted Percentage Dissatisfied (PPD).

Ride Comfort forms a core design aspect for suspension and is to be considered as primary requirement for vehicle performance in terms of drivability and uptime of passenger. Maintaining a balance between ride comfort and handling poses a major challenge to finalize the suspension specifications. The objective of this project it to perform ride- comfort analysis for a commercial truck using MATLAB Simulink. First, benchmarking was carried out on a 4x2 commercial truck and the physical parameters were obtained. Further, a mathematical model is developed using MATLAB Simulink R2015a and acceleration- time data is collected. An experimentation was carried out on the truck at speeds of 20 kmph, 30 kmph, 40 kmph and 50 kmph over a single hump to obtain actual acceleration time domain data. The model is then correlated with actual test over a single hump. This is followed by running the vehicle on Class A, B & C road profiles to account for random vibrations.