Search Results

With the huge improvements made during the last years in the area of integrated safety systems, they are one of the main contributors to the massively rising complexity within automotive systems. However, this enormous complexity stimulates the demand for methodologies supporting the efficient development of such systems, both in terms of cost and development time. Within this work, we propose a co-simulation-based approach for the validation of integrated safety systems. Based on data measurements gained from a test bed, models for the sensors and the distributed safety system are established. They are integrated into a co-simulation environment containing models of the ambience, driving dynamics, and the crash-behavior of the vehicle. Hence, the complete heterogeneous system including all relevant effects and dependencies is modeled within the co-simulation.

Driving cycles are valuable tools for emissions calibration at engine and powertrain test beds. While generic velocity profiles were sufficient in the past, legislative changes and increasing complexity of powertrain and exhaust aftertreatment systems require a new approach: Realistically transient cycles - which include critical driving maneuvers and can be tailored to a specific powertrain configuration - are needed to optimize the emission behavior of the said powertrain. For the generation of realistic velocity profiles, the Markov chain approach has been widely used and described in literature. However, this approach, so far, has only been used to generate cycles that are statistically representative of a large database of real driving trips, which is typically not available during the early stages of development of a new powertrain.

As computational methodologies become more integrated into industrial vehicle pre-development processes the potential for high transient vehicle thermal simulations is evident. This can also been seen in conjunction with the strong rise in computing power, which ultimately has supported many automotive manufactures in attempting non-steady simulation conditions. The following investigation aims at exploring an efficient means of utilizing the new rise in computing resources by resolving high time-dependent boundary conditions through a series of averaging methodologies. Through understanding the sensitivities associated with dynamic component temperature changes, optimised boundary conditions can be implemented to dampen irrelevant input frequencies whilst maintaining thermally critical velocity gradients.

Virtual testing has grown to be an efficient tool in vehicle passive safety design. Most simulations currently are deterministic. Since the responses observed in real-life and standardized tests are greatly affected by scatter, a stochastic approach should be adopted in order to improve the predictability of the numerical responses with respect to the experimental data. In addition, an objective judgement of the performance of numerical models with respect to experimental data is necessary in order to improve the reliability of virtual testing. In the European VITES & ADVANCE project the software tool Adviser was developed in order to fulfil these two requirements. With Adviser, stochastic simulations can be performed and the quality of the numerical responses with respect to the experimental can be objectively rated using pre-defined and user-defined objective correlation criteria. The software Adviser was used to develop a stochastic HybridIII 50th% Madymo numerical model.

The AUTomotive Open System ARchitecture (AUTOSAR) Development Partnership has published early 2008 the specifications Release 3.0 [1], with a prime focus on the overall architecture, basic software, run time environment, communication stacks and methodology. Heavy developments have taken place in the OEM and supplier community to deliver AUTOSAR loaded cars on the streets starting 2008 [2]. The 2008 achievements have been: Improving the specifications in order to secure the exploitation for body, chassis and powertrain applications Adding major features: safety related functionalities, OBD II and Telematics application interfaces.

Reductions of hardware costs as well as implementations of new innovative functions are the main drivers of today's automotive electronics. Indeed more and more resources are spent on adapting existing solutions to different environments. At the same time, due to the increasing number of networked components, a level of complexity has been reached which is difficult to handle using traditional development processes. The automotive industry addresses this problem through a paradigm shift from a hardware-, component-driven to a requirement- and function-driven development process, and a stringent standardization of infrastructure elements. One central standardization initiative is the AUTomotive Open System ARchitecture (AUTOSAR). AUTOSAR was founded in 2003 by major OEMs and Tier1 suppliers and now includes a large number of automotive, electronics, semiconductor, hard- and software companies.

Advanced Driver Assistance systems support the driver in his driving tasks. They can be designed to enhance the driver's performance and/or to take over unpleasant tasks from the driver. An important optimization goal is to maintain the driver's activation at a moderate level, avoiding both stress and boredom. Functions requiring a situational interpretation based on the vehicle environment are associated with lower performance reliability than typical stability control systems. Thus, driver assistance systems are designed assuming that drivers will monitor the assistance function while maintaining full control over the vehicle, including the opportunity to override as required. Advanced driver assistance systems have a substantial potential to increase active safety performance of the vehicle, i.e., to mitigate or avoid traffic accidents.

Aerodynamic performance assessment of automotive shapes is typically performed in wind tunnels. However, with the rapid progress in computer hardware technology and the maturity and accuracy of Computational Fluid Dynamics (CFD) software packages, evaluation of the production-level automotive shapes using a digital process has become a reality. As the time to market shrinks, automakers are adopting a digital design process for vehicle development. This has elevated the accuracy requirements on the flow simulation software, so that it can be used effectively in the production environment. Evaluation of aerodynamic performance covers prediction of the aerodynamic coefficients such as drag, lift, side force and also lift balance between the front and rear axle. Drag prediction accuracy is important for meeting fuel efficiency targets, prediction of front and rear lifts as well as side force and yawing moment are crucial for high speed handling.

In large-scale industrial simulations the numerical prediction of fracture in sheet metal forming operations as well as in crash events is still a challenging task of high social and economic relevance. Among several approaches presented in literature, the authors and their colleagues developed a model which accounts each for three different mechanisms leading finally to fracture in thin sheet metals: the local instability (necking), ductile normal fracture and ductile shear fracture. The focus of this paper is to develop and validate a new approach to improve the predictive capabilities for fracture triggered by localized necking for a wide variety of steel grades. It is well known that after the onset of a local instability additional strain is still necessary to induce fracture. In a numerical simulation using shell elements this post instability strain becomes of increasing importance when the ratio of the characteristic shell element edge length to its thickness decreases.

Within the pre-development phase of a vehicle validation process, the role of computational simulation is becoming increasingly prominent in efforts to ensure thermal safety. This gain in popularity has resulted from the cost and time advantages that simulation has compared to experimental testing. Additionally many of these early concepts cannot be validated through experimental means due to the lack of hardware, and must be evaluated via numerical methods. The Race Track Simulation (RTS) can be considered as the final frontier for vehicle thermal management techniques, and to date no coherent method has been published which provides an efficient means of numerically modeling the temperature behavior of components without the dependency on statistical experimental data.

A computational analysis of underbody windnoise sources on a production automobile at 180 km/h free stream air speed and 0° yaw is presented. Two different underbody geometry configurations were considered for this study. The numerical results have been obtained using the commercial software PowerFLOW. The simulation kernel of this software is based on the numerical scheme known as the Lattice-Boltzmann Method (LBM), combined with a two-equation RNG turbulence model. This scheme accurately captures time-dependent aerodynamic behavior of turbulent flows over complex detailed geometries, including the pressure fluctuations causing wind noise. Comparison of pressure fluctuations levels mapped on a fluid plane below the underbody shows very good correlation between experiment and simulation. Detailed flow analysis was done for both configurations to obtain insight into the transient nature of the flow field in the underbody region.

In order to protect occupants from the risk of serious injury in event of side impact, passenger vehicles are designed to fulfil specific legislative and consumer impact test requirements. These are generally different for each of the major markets of the world. The tests use different configurations and percentile dummies (anthropomorphic test devices). Aside from the problem of finding an optimal design, the reliable evaluation of the robustness, i.e. the sensitivity of unavoidable scatter of design variables due to the structural response, is becoming increasingly important. For this purpose simulation is a well established tool in the development process in the automotive industry. The integration of FE-dummies and restraint systems in side impact simulations enables the study of the effect of dummy loading. ABAQUS/Explicit is a promising new software package for gaining more accuracy in crashworthiness and occupant protection simulations.

This article focuses on model based development of electronic control units (ECUs) in the automotive domain. The use of model-based approaches solves requirements for the fast-growing integration of formerly isolated logical functions in complex distributed networks of heavily interacting ECUs. One fundamental property of such an approach is the existence of an adequate modeling notation tailored to the specific needs of the application domain together with a precise definition of its syntax and its semantics. However, although these constituents are necessary, they are not sufficient for guaranteeing an efficient development process of ECU networks. In addition, methodical support which guides the application of the modeling notation must be an integral part of a model-based approach.

What are the requirements of customers in an urban environment? What will sustainable mobility look like in the future? This presentation gives an overview of the integrated approach used by BMW to develop the BMW i3 - a purpose-built battery electric vehicle. Very low driving resistances for such a vehicle concept enable the delivery of both impressive range and driving excitement. A small optional auxiliary power unit offers range security for unexpected situations and opens up BEVs to customers who are willing to buy a BEV but are still hesitant due to range anxiety. Additional electric vehicles sold to the formerly range anxious will create additional electric miles. Presenter Franz Storkenmaier, BMW Group

The dramatic increase in data and information exchange has lead to increased communication network complexity within the subsystems of the powertrain itself as well as in all other subsystems of the vehicle. It is essential to manage this complexity during the development process. Applying new processes and methods such as vehicle functions and systems orientation in a top-down structural approach creates a powerful support in development of innovative powertrains. Several technical integration examples of powertrain functions are illustrated for the purpose of demonstrating customer-related advantages. Vehicle functions and systems orientation also has significant impact on organisational structures and cooperation methods to achieve maximum synergies as well as efficient vehicle communication architectures.

Sport Activity Vehicle (SAV) share a growing market of an entirely new class of vehicles. Outstanding comfort in traditional on-road and also off-road terrain combined with leading edge technology are basic features of this concept. But in addition to that, the SAV has to offer the same overall safety features, expected by e.g. a luxury-segment sedan. A way to ensure the BMW X5 becoming one of the safest cars was the consequent use of simulation techniques in passive safety development. This paper deals with introduction of a CAE driven development process for passive safety in the BMW X5 project, focusing on examples in front and side impact.

The NVH-development cycle of vehicle components often requires a source characterization separated from the vehicle itself, which leads to the implementation of test bench setups. In the context of frequency based substructuring and transfer path analysis, a component can be characterized using Blocked Forces. The following paper provides a comparison of methods between an acceleration-based in-situ and a new hybrid in-situ Blocked Force determination, using measurements of an artificially excited electric power steering (EPS). Under real-life conditions on a test rig, the acceleration-based in-situ approach often shows limitations in the lower frequency range, due to relatively bad signal-to-noise ratio at the indicator sensors, while delivering accurate results in the higher spectrum. Due to considerable loads on components in operation, the stiffness of the test-rig cannot be decreased arbitrarily.

A comprehensive experimental study was conducted to investigate human movements when entering a vehicle. The primary goal of this study was to understand the influence of environmental changes on entry motions selected by a driver to enter a vehicle. The adjustable hardware setup “VEMO” (Variable Entry Mockup) was used for the experiments. With VEMO it is possible to simulate different types and classes of vehicle configurations. Around 30 test persons of different anthropometry participated in the experiments. The visual measurement system VICON was used for motion capturing, motion data cleaning and biomechanical analysis. The results corroborate the theory of leading body parts (LBPs) i.e. body parts that control targeted movement of the entire body. It could be demonstrated how motion patterns of LBPs, including spatial and dynamic characteristics such as orientation and velocity, respond to modifications of the geometrical environment.

The trend in the previous years showed that an ideal product is not obtained as a sum of development results of several separated disciplines but rather as a result of a holistic multidisciplinary CAE approach. In the course of the whole component development process it is necessary to consider all functions of an individual component equivalent to their importance in the system as a whole, in order to achieve both a technical and a financial optimum. The predictability and the accuracy of an individual computational method have to be regarded against the background of the entire simulation process. A continuative CAE-standard and a harmonious interaction between the different computational disciplines promise more success than focusing specifically on individual topics and thereby neglecting the “bigger picture”. This awareness provided the basis for a decision to change the entire crash simulation software to ABAQUS.

The validity of numerical simulations is still limited by the unknown failure of materials when nonlinear load paths in successive stamping and crash processes occur. Localized necking is the main mechanism for fractures in ductile sheet metal. The classical forming limit curve (FLC) is limited to linear strain paths. To include the effects of nonlinear strain paths a theoretical model for instability (algorithm CRACH) has been used. The algorithm has been developed on the basis of the Marciniak model [8]. The calibration and validation of this approach is done by a set of multistage experiments under static and dynamic strain rates for a mild steel.