Search Results

This paper summarizes the Fast Fourier Transform (FFT) methodology, special equipment, set-up and testing that is recommended to properly characterize the surface of bearing journals that will not result in objectionable noise or vibration. Traditional surface profiles and finish callouts do not capture some of the key characteristics for addressing what is often the customer's greatest complaint, noise. Noise can vary based on the sensitivity of the vehicle but understanding how to accurately describe (design, test, and measure) a surface for a given vehicle can result in an optimized design and reduce process time during manufacturing. Furthermore, this paper will recommend techniques for determining the proper limits of the FFT callouts.

The development process of a water pump impeller used on a sport utility vehicle engine is described. A review of the design process is presented in this paper including the computer-aided flow analysis together with testing procedures. By computer modeling, one can estimate the coolant flow characteristics of a given impeller blade shape for providing increased cooling performance and improved efficiency on the engine. It also provides directions for the improved design. The test data are used specifically to confirm the analysis results.

With fuel costs continuing to rise, and with regulations seeking to lower overall fuel emissions, improved fuel economy has become indispensible for today's gasoline engine designer. Reducing engine friction is an effective means of improving fuel economy and specific engine components have been developed towards this objective. Chain drive system components are no exception to this trend. In an attempt to decrease friction loss in the timing chain system and thereby improving fuel economy, the following three topics were studied: 1) defining sources of friction loss; 2) investigating the effect(s) of each loss factor using friction simulation; and, 3) evaluating methods to minimize friction losses. Chain system friction loss can occur when the chain slides on the Arm & Guide face. Friction loss can also occur between the chain link and pin joint, and during chain engagement with the sprocket.

Scuffing is one of the major problems that influence the life cycle and reliability of several auto components, including engine cylinder kits, flywheels, camshafts, crankshafts, and gears. Ferrous casting materials, such as gray cast iron, ductile cast iron and austempered ductile cast iron (ADI) are widely applied in these components due to their self-lubricating characteristics. The purpose of this research is to determine the scuffing behavior of these three types of cast iron materials and compare them with 1050 steel. Rotational ball-on-disc tests were conducted with white mineral oil as the lubricant under variable sliding speeds and loads. The results indicate that the scuffing initiation is due to either crack propagation or plastic deformation. It is found that ADI exhibits the highest scuffing resistance among these materials.

An ignition delay correlation was developed for a toluene reference fuel (TRF) blend that is representative of automotive gasoline fuels exhibiting two-stage ignition. Ignition delay times for the autoignition of a TRF 91 blend with an antiknock index of 91 were predicted through extensive chemical kinetic modeling in CHEMKIN for a constant volume reactor. The development of the correlation involved determining nonlinear least squares curve fits for these ignition delay predictions corresponding to different inlet pressures and temperatures, a number of fuel-air equivalence ratios, and a range of exhaust gas recirculation (EGR) rates. In addition to NO control, EGR is increasingly being utilized for managing combustion phasing in spark ignition (SI) engines to mitigate knock. Therefore, along with other operating parameters, the effects of EGR on autoignition have been incorporated in the correlation to address the need for predicting ignition delay in SI engines operating with EGR.

Advanced High-Strength Steels (AHSS) have become an essential part of the lightweighting strategy for automotive body structures. The ability to fully realize the benefits of AHSS depends upon the ability to aggressively form, trim, and pierce these steels into challenging parts. Tooling wear has been a roadblock to stamping these materials. Traditional die materials and designs have shown significant problems with accelerated wear, galling and die pickup, and premature wear and breakage of pierce punches. [1] This paper identifies and discusses the tribological factors that contribute to the successful stamping of AHSS. This includes minimizing tool wear and galling/die pick-up; identifying the most effective pierce clearance (wear vs. burr height) when piercing AHSS; and determining optimal die material and coating performance for tooling stamping AHSS.

High frequency ignition (HFI) and conventional transistor coil ignition (TCI) were investigated with an optically accessible single-cylinder research engine to gain fundamental understanding of the chemical reactions taking place prior to the onset of combustion. Instead of generating heat in the gap of a conventional spark plug, a high frequency / high voltage electric field is employed in HFI to form chemical radicals. It is generated using a resonant circuit and sharp metallic tips placed in the combustion chamber. The setup is optimized to cause a so-called corona discharge in which highly energized channels (streamers) are created while avoiding a spark discharge. At a certain energy the number of ionized hydrocarbon molecules becomes sufficient to initiate self-sustained combustion. HFI enables engine operation with highly diluted (by air or EGR) gasoline-air mixtures or at high boost levels due to the lower voltage required.

For years powder metal (P/M) nickel steel sprockets have been in use in the SUV Transfer Case market. The heat-treated, nickel steel powder metal provides a high strength and high wear resistant material for this very demanding application. Recently the cost of nickel has increased from $5 / lb Oct'05 to $24 / lb May'07. Because of this almost 5 fold increase in the commodity price a replacement material for the powder metal nickel steel was sought that would have comparable properties, comparable processing steps at a raw material cost that would be equal to the nickel steel powder metal prices of 2005. A replacement material was found that has comparable properties at a competitive price. Material composition, testing data and microscopic analysis will be presented.

The double linear damage model developed by Manson and Halford helps to determine the knee point, which is the intersection between the two straight lines. The damage to the component is then calculated based on this knee point. The new approach mentioned in this paper helps to evaluate the damage on the component in a slightly different way. It uses the knee points as mentioned by Manson and Halford and decomposes the damage to the component for Phase I & Phase II. It then uses the equivalent damage approach and establishes the damage to the component. This will be explained with an example.

Hydraulic, mechanical, and electro-magnetic technologies have been the primary means for torque management in today's drivetrains. Recent advances in electronic controls have provided even greater performance benefits for these base technologies. These facts coupled with an extended period of design and development for these drivetrain systems make the introduction of a new technology very challenging. However, recent developments at Borg Warner's Powertrain Technical Center have shown that a new technology, hydro-mechanical technology, may hold great promise in solving some of the fundamental problems and limitations of today's torque management technologies. This paper illustrates drivetrain applications where hydro-mechanical technology offers new and improved performance benefits for some of drivetrain's oldest problems. The opportunity to bring a new technology to the market in drivetrains also provides a new opportunity for powdered metallurgy (P/M) content in same.

In an effort to improve the dent resistance of exterior body panels at reduced steel thicknesses, some automobile manufacturers have pursued the application of bake hardenable steels. Unfortunately, bake hardenable steels have only been available as cold rolled or with electro-zinc or electro zinc/iron coatings. This situation has been a deterrent for those automobile manufacturers that prefer the use of hot dip galvanneal coatings. Recently, the interest in hot dip galvanneal bake hardenable steels has led to the investigation and development of this more advanced steel grade. This paper presents the results of a stamping trial and dent testing on three exposed hot dip galvannealed materials; i) Regular Ultra Low Carbon (ULC), ii) Rephosphorized ULC, and iii) Rephosphorized Bake Hardenable ULC steel.

Today, some vehicles include a regenerative-braking system such as the electrical motor-generator that converts the vehicle's kinetic energy into electrical energy to recharge one or more vehicle batteries. The idea is to use air flow to produce additional electrical energy in response to deceleration of the vehicle. With the Wind Power Generator System (WPGS) as a green system, a vehicle can produce extra energy, reduce gasoline usage, and reduce air pollution.