Search Results

The advantages and disadvantages for the current oil consumption measurement systems, including the real-time oil consumption measurement and traditional weight methods, are reviewed. Based on the review, the Smart Oil Consumption Measuring System developed by Cummins Engine Co. in an effort to resolve some of the disadvantages of the systems developed earlier, especially compared to the Gravity Fed oil consumption measurement system, will be discussed. In addition, the uncertainty analysis of the Smart Oil Consumption Measuring System will also be briefly discussed here. The Smart Oil Consumption Measuring System has proven to be an effective tool to measure the oil consumption at almost any engine test conditions, including the steady and cyclic tests in a shorter time than most of traditional oil consumption measurement systems.

Corrosive wear of non-ferrous engine components by lubricants is a concern of all major heavy duty diesel engine manufacturers since warranty on key engine components has been extended to 500,000 miles. Several commercial lubricants have been linked to premature cam and rod bearing failures induced by corrosion in certain fleets. Although the overall failure rate is low, specific fleets have experienced significantly higher failure rates due to the lubricants used. These failures usually occur at high mileages but less than 500,000 miles. This kind of slow corrosion easily escapes detection of engine tests contained in current oil specifications, and it represents a serious issue in long term warranty cost to diesel engine manufacturers. A comprehensive fleet database has been established to identify the most corrosive lubricants. These lubricants have served as reference oils to develop a corrosion bench test.

The specific goal of this project was to determine if there is a difference in the lube oil degradation rates in a heavy-duty diesel engine equipped with an EGR system, as compared to the same configuration of the engine, but minus the EGR system. A secondary goal was to develop FTIR analysis of used lube oil as a sensitive technique for rapid evaluation of the degradation properties of lubricants. The test engine selected for this work was a Caterpillar 3176 engine. Two engine configurations were used, a standard 1994 design and a 1994 configuration with EGR designed to meet the 2004 emissions standards. The most significant changes in the lubricant occurred during the first 50-100 hours of operation. The results clearly demonstrated that the use of EGR has a significant impact on the degradation of the engine lubricant.

This paper discusses the various process changes, engine improvements, and equipment evolution that have contributed to significant increases in test productivity for heavy duty engines over the past several years. It deals with the development of short test cycles, methods of diagnosing operating problems, methods of maintaining test accuracy and discusses systems for minimizing test equipment down time. Finally it presents historical overview of the changes as they occurred at Cummins Engine Company and how performance improved over that transition period.

A number of wear resistant coatings has been developed using physical vapor deposition(PVD) process. However this coating process has not yet been widely used in the automotive industry. The purpose of this work was to evaluate thin PVD coatings such as diamond like carbon doped with tungsten (W-DLC), molybdenum-disulfide doped with aluminum (MoS2-Al), and chrome nitride (CrN). Some of these coatings were previously found to have low friction, high wear resistance, or both when tested in unlubricated conditions. In the present work, the experiments were conducted using a Cameron-Plint apparatus in lubricated conditions. The ring counterfaces used were Cr-plated and gas-nitrided compression rings. Our data also indicated that some PVD coatings with thicknesses in the same order of magnitude as the surface roughness of the liners did show some improvement in liner wear resistance. The suitability of thin coatings for liner applications needs additional study.

High Velocity Oxygen Fuel sprayed face coatings have shown great promise for piston rings used for High Power Density Diesel Engines. Various coatings have been tested on both wear test rigs and in engines. A highly dense HVOF cermet coating was developed with reasonable crack resistance during service. The HVOF coated piston rings wore three to six times lower than chrome plating. Cylinder liner (counter face) wear was found to be one to three times higher than chrome. However, engine oil consumption and blow by were within normal values. The HVOF coating is considered to be an excellent replacement for chrome plating. The coating process is more environmentally friendly than the chrome plating process. Also, the coating has potentially lower or equivalent production cost when compared to chrome.

A high horsepower, low heat rejection diesel engine is being developed to meet future Army heavy combat vehicle requirements. This engine features high power output in a compact design that is oil-cooled allowing for a significant reduction in radiator size. This design requires a lubricant which can survive a sump temperature of 160°C, for 300 hours with transient sump temperature surges to over 177°C. A comprehensive high temperature lubricant development program has been initiated to address the need for this new design. A modified Cummins 10 liter diesel engine was used to simulate the operating condition of this low heat rejection engine. The premium commercial lubricant that was tested survived only 58 hours before completely losing oxidative stability. Several of the experimental lubricants completed the 200-hour peak torque endurance test.

The ability of a piston oil ring to conform to liner distortions during engine operation is directly related to its radial stiffness. The ability to conform is also very important for controlling lubricant oil consumption and emissions. This paper describes the procedure utilized to investigate the technical feasibility of using flexible high performance engineering plastics to replace metal as base material for oil rings. Bench tests and engines were used to select and evaluate different types of plastics for wear resistance and structural integrity. Engine test results indicated no structural failures but wear levels were found to be unacceptably high for use in durable heavy duty diesel engines.

A laboratory method has been developed to rank the scuff resistance of piston ring coatings. This method employs a standard wear test apparatus with a specially designed sample holder. Scuff resistance of electrolytic chrome, thermal spray and physical vapor deposition (PVD) face coatings have been examined. Based on this method, examined PVD coatings produced the highest scuff resistance of all the tested face coatings.

The entire engine lubrication system has been represented by a series-parallel network of flow passages and flow elements. The pressure distribution and flow rates in the network were computed according to pressure-flow characteristics of each element. The pressure-flow relationship for each network element was estimated using empirical pipe friction, expansion, and bend loss coefficients, as well as by using test rig results and a steady-state journal bearing model. The journal bearing model is basically that of the classical short bearing model with provision for heat transfer to the oil and the relative thermal growth of the journal and bearing system. When compared with diesel engine tests, the simulation predicted the pressure distribution throughout the engine and the flow rate through each branch within 10%.

Reports of disabling diesel engine seal failures which accompanied the introduction of low sulfur diesel fuel in October '93 prompted an in-depth survey of diesel fuel chemical and physical properties. The purpose of the survey was to anticipate other possible problems which might arise with the newly introduced low sulfur fuels. The survey will produce a database containing over 1000 number 2 diesel fuels from various parts of the US. About 75% of the samples tested were on-highway low sulfur diesel fuels. Samples analyzed were from the D-A Lubricant Company, Cummins customers failures (truck fleets of various sizes), and a number of retail fueling stations. Properties under investigation are % Sulfur, Cloud/Pour Points, Viscosity, API Gravity, TAN/TBN, Boiling Range, Aromatics content, Heat Content, Lubricity, and Peroxide number.