Search Results

The use of virtual prototyping early in the design stage of a product has gained popularity due to reduced cost and time to market. The state of the art in vehicle simulation has reached a level where full vehicles are analyzed through simulation but major difficulties continue to be present in interfacing the vehicle model with accurate powertrain models and in developing adequate formulations for the contact between tire and terrain (specifically, scenarios such as tire sliding on ice and rolling on sand or other very deformable surfaces). The proposed work focuses on developing a ground vehicle simulation capability by combining several third party packages for vehicle simulation, tire simulation, and powertrain simulation. The long-term goal of this project consists in promoting the Digital Car idea through the development of a reliable and robust simulation capability that will enhance the understanding and control of off-road vehicle performance.

Motorcycle usage continues to expand globally. Motorcycles use various fuels in different countries and regions, and it is required that they comply with emissions and fuel consumption regulations as specified in UN-GTR No.2 (WMTC). In general, a motorcycle engine has a large bore diameter and a high compression ratio due to demands of high performance. Poor fuel quality may cause damage to the engine, mainly by knocking. Knock control systems utilizing high-frequency vibration detection strategies like knock sensors, which are equipped on several sport-touring motorcycles, are not used widely for reasons of complex construction and high cost. This research aims to develop a new concept of combustion control for common motorcycle as an alternative.

This work presents a methodology to determine the off-cycle fuel economy benefit of a 2-Layer HVAC system which reduces ventilation and heat rejection losses of the heater core versus a vehicle using a standard system. Experimental dynamometer tests using EPA drive cycles over a broad range of ambient temperatures were conducted on a highly instrumented 2016 Lexus RX350 (3.5L, 8 speed automatic). These tests were conducted to measure differences in engine efficiency caused by changes in engine warmup due to the 2-Layer HVAC technology in use versus the technology being disabled (disabled equals fresh air-considered as the standard technology baseline). These experimental datasets were used to develop simplified response surface and lumped capacitance vehicle thermal models predictive of vehicle efficiency as a function of thermal state.

The Drive By Wire (hereafter referred to as DBW) system is the electronically throttle control system. It controls a throttle valve in order to aim at a suitable throttle position according to an engine operating condition and a demand of driver or rider. This system is basically composed of a throttle body with driving motor, an Accelerator Position Sensor (hereafter referred to as APS), and an Electronic Control Unit (hereafter referred to as ECU). The DBW system is spreading to motorcycle field as replacement of existing mechanical intake control system. This is because there are some advantages as the following especially in the large displacement model: capability for installation of several functions, flexibility in adaptation to recent environmental regulations, and effect on reduction of system cost, etc. In general, the motorcycle has some unique features compared with the automobile. Among them, important features for the DBW system are following three points.

The performance of Gasoline Direct Injection (GDI) engines is governed by multiple physical processes such as the internal nozzle flow and the mixing of the liquid stream with the gaseous ambient environment. A detailed knowledge of these processes even for complex injectors is very important for improving the design and performance of combustion engines all the way to pollutant formation and emissions. However, many processes are still not completely understood, which is partly caused by their restricted experimental accessibility. Thus, high-fidelity simulations can be helpful to obtain further understanding of GDI injectors. In this work, advanced simulation and experimental methods are combined in order to study the spray characteristics of two different 3-hole GDI injectors.

Fuel spray injected by a port injector has significant effects on engine power output and combustion efficiency. For this reason, it is necessary to atomize fuel into fine droplets and accurately supply it without being susceptible to any changes in temperature or negative pressure affected by engine. This document introduces an atomization technique with optimized layout of nozzle holes and drastically reduced pressure loss (energy loss) in the flow under a needle valve seat. It also describes an injector having a short fuel flow path and a small dead volume under the valve seat, which can have good resistance against any changes in temperature and negative pressure.

The medium and heavy duty vehicle industry has fostered an increase in emissions research with the aim of reducing NOx while maintaining power output and thermal efficiency. This research describes a proof-of-concept numerical study conducted on a Caterpillar single-cylinder research engine. The target of the study is to reduce NOx by taking a unique approach to combustion air handling and utilizing enriched nitrogen and oxygen gas streams provided by Air Separation Membranes. A large set of test cases were initially carried out for closed-cycle situations to determine an appropriate set of operating conditions that are conducive for NOx reduction and gas diffusion properties. Several parameters - experimental and numerical, were considered. Experimental aspects, such as engine RPM, fuel injection pressure, start of injection, spray inclusion angle, and valve timings were considered for the parametric study.