Search Results

Flow separation is one of the primary causes of increase in form drag in vehicles. This phenomenon is also visible in the case of lightweight vehicles moving at high speed, which greatly affects their aerodynamics. Spherical depressions maybe used to delay the flow separation and decrease drag in such vehicles. This study aims for optimization of aspect ratio (AR) of spherical depressions on hatchback cars. Spherical depressions were created on the bonnet of a generalized light vehicle Computer-Aided Design (CAD) model. The diameter of each spherical depression was set constant at 60 mm, and the center-to-center distance between consecutive spherical depressions is fixed at 90 mm. The AR of spherical depressions was taken as the parameter that was varied in each model. ARs 2, 4, 6, and 8 were considered for the current investigation. Three-dimensional (3D) CFD analyses were then performed on each of these models using a validated computational model.

Vehicle performance is highly dependent on the design and material used. Fairing of a Human Powered Vehicle (HPV) is responsible for the reduction in the aerodynamic drag force and its material determines the overall weight and the top speed of the vehicle. Selection of material for fairings depends on various physical, mechanical and manufacturing properties along with practical considerations like availability of material. Today, an ever-increasing variety of composite materials and polymers are available, each of them possessing their own characteristics, applications, advantages and limitations. Many automotive composites are used for manufacturing fairings. Materials like Carbon fiber, Glass fiber (E glass, S glass), Aramid fiber (Kevlar 29, Kevlar 49) are some of the viable options that have been used in the past for manufacturing fairing of HPVs.

Increased dependency on fossil fuels has led to its depletion as well as affected the environment adversely. Moreover, increasing crude oil prices is pressurizing vehicle manufacturers to invent new technology so as to increase fuel economy and at the same time to keep emissions under control. Hydrogen has gained popularity not just in terms of being an abundant alternative but also due to being a very clean propellant. In the present investigation, hydrogen boosting has been performed on an SI engine running on gasoline-methanol and ethanol-gasoline blends to determine the additional advantages of the same compared to pure gasoline operation. The engine selected for experimental analysis is a single cylinder, air cooled spark ignition engine that has been modified for hydrogen injection in the intake manifold prior to the port with the injection timing being held constant throughout the experiment.

Drag and lift are the primary aerodynamic forces experienced by automobiles. In competitive automotive racing, the design of inverted wings has been the subject of much research aimed at improving the performance of vehicles. In this direction, the aerodynamic impact of change in maximum camber of the flap element and ground effect in a double-element inverted airfoil was studied. The National Advisory Committee for Aeronautics (NACA) 4412 airfoil was taken as the constant main element. The camber of the flap element was varied from 0% to 9%, while ground clearance was varied from 0.1c to 1.0c. A two-dimensional (2D) Computational Fluid Dynamics (CFD) study was performed using the realizable k-ε turbulence model in ANSYS Fluent 18.2 to analyze the aerodynamic characteristics of the airfoil. Parameters such as drag coefficient, lift coefficient, pressure distribution, and wake flow field were investigated to present the optimum airfoil configuration for high downforce and low drag.

Internal Combustion engines have been a significant component of the industrial development in the 20th and 21st centuries. However, the high working temperatures cause extensive wear and tear among the parts and results in a loss in fuel efficiency and ultimately seize the engine. To prevent this, there was a need for a cooling system. The current systems cool the vehicle's engine by transferring heat from the engine to the coolant/water in the water jacket from where it reaches the radiator via tubes, and the hot temperature coolant is cooled. This article proposes a change in the design of radiator fins to improve the overall cooling efficiency of such systems. As radiator fins are instrumental in the heat transfer process, a design change in them results in substantial changes in the output efficiency results. The central concept that is utilized is to increase the surface area of the fins, which would increase the rate of heat loss from the pipes.

While riding cycles, cyclists usually experience an aerodynamic drag force. Over the years, there has been a global effort to reduce the aerodynamic drag of a cycle. Fenders affect the aerodynamic drag of a cycle to a large extent, and fender coverage has a pronounced effect on the same. In this article, various fender coverage angles, varying from 60° to 270°, were studied to predict the aerodynamic drag with the help of a validated CFD model in SolidWorks Flow Simulation. The model was based on the Favre-Averaged Navier-Stokes (FANS) equations solved using the k-ɛ model. It was predicted that aerodynamic drag coefficient reduced fender coverage angle up to 135°, and thereafter started increasing. Analyses were carried out at velocities of 6 m/s, 8 m/s and 10 m/s and the results were found to be similar, with a minimum aerodynamic drag coefficient at 135° occurring in all the cases under study.

The Aerofoil theory along with its design has integrated itself into the vast areas of applications ranging from Automobile, Aeronautical, Wind Turbine, Micro-Vehicles, UAVs applications. In this paper, knowing the intricacy of the airfoil's applications, A MATLAB Code for NACA-2415 Airfoil is developed and a Model with dimensions c=180mm, w=126mm, tmax=27mm is generated. The model is then subjected to Flow Simulation with various input parameters: Reynolds Numbers taken are- (REN-1) 105 and (REN-2) 2×105 [Laminar External Flow], Angles of attack taken are-0°, 4°, 8°, 12°. The pressure and velocity distribution along the airfoil sketch curve are graphed qualitatively, emphasizing on the flow separation leading to the transition from laminar to turbulent flow. The various aerodynamics characteristic curves for coefficient of pressure, coefficient of lift and coefficient of drag are plotted against different angle of attacks for REN-1 and REN-2.

The functions of a piston ring are to seal off the combustion pressure, to distribute and control the oil, to transfer heat and to stabilize the piston. Most piston rings and metallic sealing rings for modern application where running conditions are severe, require some form of coating to minimise abrasion and corrosion. The piston ring coating improves the life of engine as well as fuel efficiency. In this study, physical vapour deposition (ion chrome plating) was investigated; plates with similar composition as the piston ring material were prepared by the casting process using induction arc furnace and sand mould. Wear test of the coating was conducted on pin on disc machine under dry conditions. The wear rate was calculated using mass loss methods on an electronic balance having least count of 1× 10−4 g.

The Continuously Variable Transmission (CVT) is a widely adopted transmission system. The operation of a CVT is simple, but successfully foretelling the longitudinal motion of a vehicle that utilizes this transmission is sophisticated. As a result, different vehicles taking part in BAJA-SAE competitions were developed using various strategies to model the vehicle’s longitudinal dynamics and CVT operation. This article aims to provide a tool for obtaining a quantitative estimate of the longitudinal performance of a CVT equipped vehicle and for the selection of an optimal drive-train gear ratio for such a vehicle. To this end, this article proposes a novel, relatively simple, and reasonably accurate mathematical approach for modeling the longitudinal motion of a vehicle utilizing a CVT, which was developed by a novel integration of existing vehicle dynamics concepts.

The behavior of flow over an automobile’s body has a large effect on vehicle performance, and automobile manufacturers pay close attention to the minimal of the details that affect the performance of the vehicle. An imbalance of downforce between the front and rear portion of the vehicle can lead to significant performance hindrances. Worldwide efforts have been made by leading automobile manufacturers to achieve maximum balanced downforce using aerodynamic elements of vehicle. One such element is the front splitter. This study aims to analyze the aerodynamic performance of automobile at various splitter overhang lengths using Computational Fluid Dynamics (CFD). For the purpose of analysis, a three-dimensional (3D) CFD study was undertaken in ANSYS Fluent using the realizable k-ε turbulence model, based on the 3D compressible Reynolds-Averaged Navier-Stokes (RANS) equations.

The growing energy demand and limited petroleum resources in the world have guided researchers towards the use of clean alternative fuels like alcohols for their better tendency to decrease the engine emissions. To comply with the future stringent emission standards, innovative diesel engine technology, exhaust gas after-treatment, and clean alternative fuels are required. The use of alcohols as a blending agent in diesel fuel is rising, because of its benefits like enrichment of oxygen, premixed low temperature combustion (LTC) and enhancement of the diffusive combustion phase. Several researchers have investigated the relationship between LTC operational range and cetane number. In a light-duty diesel engine working at high loads, a low-cetane fuel allowed a homogeneous lean mixture with improved NOx and smoke emissions joint to a good thermal efficiency.

This paper presents a CFD analysis for drag reduction of a Class 8 Tractor-Trailer arrangement. A three dimensional bluff body model of the truck is simulated for a zero degree yaw angle at a speed of 50 miles per hour for a Reynolds Number of 3.3 million. In this paper, the role of vortex generators is investigated for overall drag reduction of the body. The key areas of interest for lowering the drag coefficient are the tractor-trailer gap and the trailer end. The designing of the body was done on DS SolidWorks whereas the CFD simulations were performed on commercial software Ansys Fluent. The Standard k-ε turbulence model was chosen for the simulation while the convergence criterion for the residuals was set at 10−6. The simple bluff body showed a drag coefficient of 1.654. The first design iteration involved increasing the tractor frontal area which resulted in a reduction of 4% in the drag coefficient.