Search Results

During the course of a fire and subsequent exposure to the environment, iron and low-carbon steels oxidize by two mechanisms: high temperature oxidation and atmospheric corrosion. Of particular interest to fire investigators are oxide properties and distribution that could be of use to better understand important characteristics of the fire such as the location the fire originated, the direction the fire traveled or even temperature versus time characteristics. This could be particularly valuable in cases where burn damage to combustible material, which is known to be an important indicator of fire origin, is so extensive that little if any material remains after the fire. However, there is little data in the literature that specifically addresses the utility of oxide properties in the context of fire investigations.

In some automotive electrical systems, it is advantageous to use power supplies and loads at two or more voltages. Often it is desirable to retain the single wire power architecture, with the car body providing the return circuit. A major difficulty in achieving this end is the matter of dealing with the possibility of a short circuit between feed wires at different voltages. It can be shown that source-side fuses cannot be relied upon to return the system to a safe state in all cases. Substantial effort was applied to this problem in the early years of the 21st century, but the results were less than completely satisfactory. Using entirely separate cable harnesses for each voltage, with physically separated routing, minimizes the risk of such a short occurring in the harness.

There is a limited amount of data currently available on the acceleration and braking performances of school buses. This paper analyzes the braking performance of various Type A and Type C school buses with hydraulic and air brakes. The effect of ABS and Non-ABS systems as well as driver experience is discussed. A comparison with passenger car braking performance is presented. The acceleration of a school bus is also presented. Evaluations of “normal” and “rapid” accelerations are presented for Type A and Type B buses. A comparison with commonly used acceleration values for various vehicles is presented.

Unintended acceleration events due to pedal misapplication have been shown to occur more frequently in older vs. younger drivers. While such occurrences are well documented, the nature of these movement errors is not well-characterized in common pedal error scenarios: namely, on-road, non-emergency stopping or slowing maneuvers. It is commonly assumed that drivers move in a ballistic or “direct hit” trajectory from the accelerator to the brake pedal. However, recent simulator studies show that drivers do not always move directly between pedals, with older drivers displaying more variable foot trajectories than younger drivers. Our study investigated pedal movement trajectories in older drivers ages 67.9 ± 5.2 years (7 males, 8 females) during on-road driving in response to variable traffic light conditions. Three different sedans and a pick-up truck were utilized.

The National Automotive Sampling System (NASS) Crashworthiness Data System (CDS) contains an abundance of field crash data. As technology advances and the database continues to grow over the years, the statistical significance of the data increases and trends can be observed. The purpose of this paper is to provide a broad-based, up-to-date, reference resource with respect to commonly sought-after crash statistics. Charts include up-to-date crash distributions by Delta-V and impact direction with corresponding injury severity rates. Rollover data is also analyzed, as well as historical trends for injury severity, belt usage, air bag availability, and the availability of vehicle safety technology.

Because the great majority of All-Terrain Vehicles (ATVs) use a solid rear axle for improved off-road mobility, these vehicles typically transition from understeer to oversteer with increased cornering severity in tests customarily used by automobile manufacturers to measure steady-state vehicle handling properties. An oversteer handling response is contrary to the accepted norm for on-road passenger vehicles and, for this reason, has drawn scrutiny from numerous researchers. In this paper, an evaluation of ATV handling is presented in which 10 participants operated an ATV that was configured to have two different steady-state cornering characteristics. One configuration produced an approximately linear understeer response (labeled US) and the other configuration transitioned from understeer to oversteer (labeled US-OS) with increasing lateral acceleration in constant-radius turn tests conducted on a skid pad.

Blunt impacts to the back of the torso can occur in vehicle crashes due to interaction with unrestrained occupants, or cargo in frontal crashes, or intrusion in rear crashes, for example. Six pendulum tests were conducted on the back of an instrumented 50th percentile male Hybrid III ATD (Anthropomorphic Test Device) to determine kinematic and biomechanical responses. The impact locations were centered with the top of a 15-cm diameter impactor at the T1 or at T6 level of the thoracic spine. The impact speed varied from 16 to 24 km/h. Two 24 km/h tests were conducted at the T1 level and showed repeatability of setup and ATD responses. The 16 and 24 km/h tests at T1 and T6 were compared. Results indicated greater head rotation, neck extension moments and neck shear forces at T1 level impacts. For example, lower neck extension was 2.6 times and 3.8 times greater at T1 versus T6 impacts at 16 and 24 km/h, respectively.

Recently, side-by-side Recreational Off-Highway Vehicles (ROVs) have brought elements of the on-road vehicle occupant environment to the off-road trail-riding world. In general, ROV occupant protection during normal operation and in accident scenarios is provided predominately by a roll cage, seatbelts, contoured seats with seat backs, handholds, and other components. Typical occupant responses include both passive (inertial) and active (muscular) components. The objective of the current study was to evaluate and quantify these passive and active occupant responses during belted operation of an ROV on a closed course, as well as during 90-degree tip-over events. Passive occupant responses were evaluated using anthropomorphic test devices (ATDs) in 90-degree tip-overs simulated on a deceleration sled.

Spine degeneration can lower injury tolerance and influence injury outcomes in vehicle crashes. To date, limited information exists on the effect of age and sex on thoracic spine 3-dimensional geometry. The purpose of this study is to quantify thoracic spinal column and canal geometry using selected geometrical measurement from a large sample of CT scans. More than 33,488 scans were obtained from the International Center for Automotive Medicine database at the University of Michigan under Institutional Review Board approval (HUM00041441). The sample consisted of CT scans obtained from 31,537 adult and 1,951 pediatric patients between the ages of 0 to 99 years old. Each scan was processed semi-automatically using custom algorithms written in MATLAB (The Math Works, Natick, MA). Five geometrical measurements were collected including: 1) maximum spinal curvature depth (D), 2) T1-to-T12 vertical height (H), 3) Kyphosis Index (KI), 4) kyphosis angle, and 5) spinal canal radius.

Advanced Driver Assistive System (ADAS) technologies have been introduced as the automotive industry moves towards autonomous driving. One ADAS technology with the potential for substantial safety benefits is forward collision warning and mitigation (FCWM), which is designed to warn drivers of imminent front-end collisions, potentiate driver braking responses, and apply the vehicle's brakes autonomously. Although the proliferation of FCWM technologies can, in many ways, mitigate the necessity of a timely braking response by a driver in an emergency situation, how these systems affect a driver's overall ability to safely, efficiently, and comfortably operate a motor vehicle remains unclear. Exponent conducted a closed-course evaluation of drivers' reactions to an imminent forward collision event while driving an FCWM-equipped vehicle, either with or without a secondary task administered through a hands-free cell phone.

Seat strength has increased over the past four decades which includes a transition to dual recliners. There are seat collision performance issues with stiff ABTS and very strong seats in rear impacts with different occupant sizes, seating positions and physical conditions. In this study, eight rear sled tests were conducted in four series: 1) ABTS in a 56 km/h (35 mph) test with a 50th Hybrid III ATD at MGA, 2) dual-recliner ABTS and F-150 in a 56 km/h (35 mph) test with a 5th female Hybrid III ATD at Ford, 3) dual-recliner ABTS in a 48 km/h (30 mph) test with a 95th Hybrid III ATD leaning inboard at CAPE and 4) dual-recliner ABTS and Escape in 40 km/h (25 mph) in-position and out-of-position tests with a 50th Hybrid III ATD at Ford. The sled tests showed that single-recliner ABTS seats twist in severe rear impacts with the pivot side deformed more rearward than the stanchion side.

Interest in rear-seat occupant safety has increased in recent years. Information relevant to rear-seat occupant interior space and kinematics are needed to evaluate injury risks in real-world accidents. This study was conducted to first assess the effect of size and restraint conditions, including belt misuse, on second-row occupant kinematics and to then document key clearance measurements for an Anthropomorphic Test Device (ATD) seated in the second row in modern vehicles from model years 2015-2020. Twenty-two tests were performed with non-instrumented ATDs; three with a 5th percentile female Hybrid III, 10 tests with a 10-year-old Hybrid III, and 9 tests with a 6-year-old Hybrid III. Test conditions included two sled bucks (mid-size car and sport utility vehicle (SUV)), two test speeds (56 and 64 km/h), and various restraint configurations (properly restrained and improperly restrained configurations). Head and knee trajectories were assessed.

Electric vehicles (EVs) and the development around them has been rapid in recent years. As the battery is the most essential component of an electric vehicle, a lot of research and analysis has been focused on ensuring safe and reliable performance of batteries. Considering the location, size, and operating conditions for EV batteries, they must be designed with an in-built safety infrastructure keeping in mind certain realistic scenarios such as fire exposure, mechanical vibration, collisions, over-charging, single cell failures, and others. In this paper, we discuss an overview of various EV battery failure mechanisms, present current safety and abuse testing methods and standards associated with such mechanisms and discuss the need for the development and implementation of additional testing standards to better characterize the safety performance of EV battery packs.

Three years of data from the Large Truck Crash Causation Study (LTCCS) were analyzed to identify accidents involving heavy trucks (GVWR >10,000 lbs.). Risk of rollover and ejection was determined as well as belt usage rates. Risk of ejection was also analyzed based on rollover status and belt use. The Abbreviated Injury Scale (AIS) was used as an injury rating system for the involved vehicle occupants. These data were further analyzed to determine injury distribution based on factors such as crash type, ejection, and restraint system use. The maximum AIS score (MAIS) was analyzed and each body region (head, face, spine, thorax, abdomen, upper extremity, and lower extremity) was considered for an AIS score of three or greater (AIS 3+). The majority of heavy truck occupants in this study were belted (71%), only 2.5% of occupants were completely or partially ejected, and 28% experienced a rollover event.

By their nature as chaotic, high-energy events, rollovers pose a high risk of injury to unrestrained occupants, in particular through exposure to projected perimeter contact and ejection. While seat belts have long been accepted as a highly effective means of retaining and restraining occupants in rollover crashes, it has been suggested that technologies such as laminated safety glazing or rollover-activated side curtain airbags (RSCAs) could alternatively provide effective occupant containment. In this study, a full-scale dolly rollover crash test was performed to assess the occupant containment capability of laminated side glazing and RSCAs in a high-severity rollover event. This allowed for the analysis of unrestrained occupant kinematics during interaction with laminated side glazing and RSCAs and evaluation of failure modes and limitations of laminated glazing and RSCAs as they relate to partial and complete ejection of unrestrained occupants.

While nearly 50 percent of occupants in side-impact collisions are in vehicles that experience a velocity change (delta-V) below 15.0 kph (9.3 mph), full scale crash testing research at these delta-Vs is limited. Understanding occupant kinematics in response to these types of side impacts can be important to the design of side-impact safety countermeasures, as well as for evaluating potential interactions with interior vehicle structures and/or with other occupants in the vehicle. In the current study, two full-scale crash tests were performed utilizing a late-model, mid-size sedan with disabled airbags. The test vehicle was impacted by a non-deformable moving barrier on the driver side at an impact speed of 10.0 kph (6.2 mph) in the first test and then on the passenger side at an impact speed of 21.6 kph (13.4 mph) in the second test, resulting in vehicle lateral delta-Vs of 6.1 kph (3.8 mph) and 14.0 kph (8.7 mph), respectively.

Low- to moderate-speed motor vehicle collisions are a common crash type and are sometimes associated with injury complaints. Understanding occupant motion (kinematics) in response to low- and moderate-speed motor vehicle collisions is important for evaluating occupant interactions with interior vehicle structures, including the restraint systems, with the ultimate goal of assessing injury potential. Furthermore, quantitative occupant kinematic data from full-scale crash testing of late-model passenger vehicles is limited for collisions at low- to moderate-speeds. The current study reports kinematic data from full-scale frontal and rear-end crash tests of late-model, mid-size sedans with delta-Vs ranging from 6.0 to 19.0 kph (3.7 to 11.8 mph) and 5.6 to 19.5 kph (3.5 to 12.1 mph), respectively. For each test vehicle, the motion of a Hybrid III 50th-percentile male anthropomorphic test device (ATD) restrained in the driver seat was recorded using high-speed onboard video.

The use of Lithium-ion batteries in the transportation sector has its own unique set of requirements such as high-power demands, cooling challenges, and risk of mechanical failure due to crashes. Active and passive components of thermal management systems in battery-powered products are designed to mitigate the effects of thermal runaway events and prevent cell-to-cell propagation. Designing safe battery-powered systems requires an understanding of how the battery pack will behave while undergoing thermal runaway, including critical data such as total energy yielded, rate of energy generation, as well as venting patterns and directions. Details such as thermal runaway energy fractions associated with the cell casing as well as vent gas and ejecta can be used to inform and optimize battery pack designs and the product as a whole. The NASA Fractional Thermal Runaway Calorimeter (FTRC) was created to measure these values.

Fires involving cars, trucks, and other highway vehicles are a common concern for emergency responders. In 2013 alone, there were approximately 188,000 highway vehicle fires. Fire Service personnel are accustomed to responding to conventional vehicle (i.e., internal combustion engine [ICE]) fires, and generally receive training on the hazards associated with those vehicles and their subsystems. However, in light of the recent proliferation of electric drive vehicles (EDVs), a key question for emergency responders is, “what is different with EDVs and what tactical adjustments are required when responding to EDV fires?” The overall goal of this research program was to develop the technical basis for best practices for emergency response procedures for EDV battery incidents, with consideration for suppression methods and agents, personal protective equipment (PPE), and clean-up/overhaul operations.

Safety-critical systems in most modern applications are designed in a way such that they provide a fail-safe operation when a fault occurs, to pose minimum risk to the user. As these systems become more sophisticated with increased functionality, it is important that their design incorporates functional safety concepts which entail detection of a potential harmful condition that prompts a corrective action to prevent hazardous events. In this paper, we discuss the significance of safety-critical systems along with the implementation of fail-safe designs in these systems. We also aim to provide an overview of functional safety as addressed in some of the industry standards and through a case study demonstrate how the concepts can be used when developing a safety-critical system.