Search Results

During the course of a fire and subsequent exposure to the environment, iron and low-carbon steels oxidize by two mechanisms: high temperature oxidation and atmospheric corrosion. Of particular interest to fire investigators are oxide properties and distribution that could be of use to better understand important characteristics of the fire such as the location the fire originated, the direction the fire traveled or even temperature versus time characteristics. This could be particularly valuable in cases where burn damage to combustible material, which is known to be an important indicator of fire origin, is so extensive that little if any material remains after the fire. However, there is little data in the literature that specifically addresses the utility of oxide properties in the context of fire investigations.

In some automotive electrical systems, it is advantageous to use power supplies and loads at two or more voltages. Often it is desirable to retain the single wire power architecture, with the car body providing the return circuit. A major difficulty in achieving this end is the matter of dealing with the possibility of a short circuit between feed wires at different voltages. It can be shown that source-side fuses cannot be relied upon to return the system to a safe state in all cases. Substantial effort was applied to this problem in the early years of the 21st century, but the results were less than completely satisfactory. Using entirely separate cable harnesses for each voltage, with physically separated routing, minimizes the risk of such a short occurring in the harness.

Studies of rollover accidents have reported crash attributes such as the number of rolls, rollout distance, initial over-the-ground speed, average roll rate, average over-the-ground deceleration, magnitude of roof deformation, cumulative damage, time and post-crash headroom. While these more general attributes are related to the repeated vehicle-to-ground impacts during a rollover, it has been previously shown [1] that a specific ground impact during a rollover and its consequences can be studied in more detail by using its acceleration time history (crash pulse or impulse) and energy loss. These two quantities are particularly meaningful to use when studying impact mechanics, however, they are limited to circumstances where the data exists, which means real-world on-road crashes cannot be used directly. Acceleration and energy data have been collected and previously published for three Subaru Forester dolly rollover tests, and have been studied in more detail in this writing.

There is a limited amount of data currently available on the acceleration and braking performances of school buses. This paper analyzes the braking performance of various Type A and Type C school buses with hydraulic and air brakes. The effect of ABS and Non-ABS systems as well as driver experience is discussed. A comparison with passenger car braking performance is presented. The acceleration of a school bus is also presented. Evaluations of “normal” and “rapid” accelerations are presented for Type A and Type B buses. A comparison with commonly used acceleration values for various vehicles is presented.

Unintended acceleration events due to pedal misapplication have been shown to occur more frequently in older vs. younger drivers. While such occurrences are well documented, the nature of these movement errors is not well-characterized in common pedal error scenarios: namely, on-road, non-emergency stopping or slowing maneuvers. It is commonly assumed that drivers move in a ballistic or “direct hit” trajectory from the accelerator to the brake pedal. However, recent simulator studies show that drivers do not always move directly between pedals, with older drivers displaying more variable foot trajectories than younger drivers. Our study investigated pedal movement trajectories in older drivers ages 67.9 ± 5.2 years (7 males, 8 females) during on-road driving in response to variable traffic light conditions. Three different sedans and a pick-up truck were utilized.

The National Automotive Sampling System (NASS) Crashworthiness Data System (CDS) contains an abundance of field crash data. As technology advances and the database continues to grow over the years, the statistical significance of the data increases and trends can be observed. The purpose of this paper is to provide a broad-based, up-to-date, reference resource with respect to commonly sought-after crash statistics. Charts include up-to-date crash distributions by Delta-V and impact direction with corresponding injury severity rates. Rollover data is also analyzed, as well as historical trends for injury severity, belt usage, air bag availability, and the availability of vehicle safety technology.

While various Advanced Driver Assistance System (ADAS) features have become more prevalent in passenger vehicles, their ability to potentially avoid or mitigate vehicle crashes has limitations. Due to current technological limitations, forward collision mitigation technologies such as Forward Collision Warning (FCW) and Automated Emergency Braking (AEB) lack the ability to consistently perform in many unique and challenging scenarios. These limitations are often outlined in driver manuals for ADAS equipped vehicles. One such scenario is the case of a stationary lead vehicle at the side of the road. This is generally considered to be a challenging scenario for FCW and AEB to address because it can often be difficult for the system to discern this threat accurately and consistently from non-threatening roadway infrastructure without unnecessary or nuisance system activations.

Because the great majority of All-Terrain Vehicles (ATVs) use a solid rear axle for improved off-road mobility, these vehicles typically transition from understeer to oversteer with increased cornering severity in tests customarily used by automobile manufacturers to measure steady-state vehicle handling properties. An oversteer handling response is contrary to the accepted norm for on-road passenger vehicles and, for this reason, has drawn scrutiny from numerous researchers. In this paper, an evaluation of ATV handling is presented in which 10 participants operated an ATV that was configured to have two different steady-state cornering characteristics. One configuration produced an approximately linear understeer response (labeled US) and the other configuration transitioned from understeer to oversteer (labeled US-OS) with increasing lateral acceleration in constant-radius turn tests conducted on a skid pad.

Many side-impact collisions occur at speeds much lower than tests conducted by the National Highway Traffic Safety Administration (NHTSA) and the Insurance Institute for Highway Safety (IIHS). In fact, nearly half of all occupants in side-impact collisions experience a change in velocity (delta-V) below 15 kph (9.3 mph). However, studies of occupant loading in collisions of low- to moderate-severity, representative of many real-world collisions, is limited. While prior research has measured occupant responses using both human volunteers and anthropometric test devices (ATDs), these tests have been conducted at relatively low speeds (<10 kph [<6.2 mph] delta-V). This study evaluated near- and far-side occupant response and loading during two side impacts with delta-V of 6.1 kph and 14.0 kph (3.8 mph and 8.7 mph).

The primary function of an airbag control module is to detect crashes, discriminate and predict if a deployment is necessary, then deploy the restraint systems including airbags and where applicable, pretensioners. At General Motors (GM), the internal term for airbag control module is Sensing and Diagnostic Module (SDM). In the 1994 model year, GM introduced its SDM on some of its North American airbag-equipped vehicles. A secondary function of that SDM and all subsequent SDMs is to record crash related data. This data can include data regarding impact severity from internal accelerometers and pre-crash vehicle data from various chassis and powertrain modules. Previous researchers have addressed the accuracy of both the velocity change data, recorded by the SDM, and the pre-crash data, but the assessment of the timing of the pre-crash data has been limited to a single family of modules (Delphi SDM-G).

The Advanced Driver Assistance System (ADAS) is a comprehensive feature set designed to aid a driver in avoiding or reducing the severity of collisions while operating the vehicle within specified conditions. In General Motors (GM) vehicles, the primary controller for the ADAS is the Active Safety Control Module (ASCM). In the 2013 model year, GM introduced an ASCM utilizing the GM internal nomenclature of External Object Calculation Module (EOCM) in some of their vehicles produced for the North American market. Similar to the Sensing and Diagnostic Module (SDM) utilized in the restraints system, the EOCM3 LC contains an Event Data Recorder (EDR) function to capture and record information surrounding certain ADAS or Supplemental Inflatable Restraint (SIR) events. The ASCM EDR contains information from external object sensors, various chassis and powertrain control modules, and internally calculated data.

Blunt impacts to the back of the torso can occur in vehicle crashes due to interaction with unrestrained occupants, or cargo in frontal crashes, or intrusion in rear crashes, for example. Six pendulum tests were conducted on the back of an instrumented 50th percentile male Hybrid III ATD (Anthropomorphic Test Device) to determine kinematic and biomechanical responses. The impact locations were centered with the top of a 15-cm diameter impactor at the T1 or at T6 level of the thoracic spine. The impact speed varied from 16 to 24 km/h. Two 24 km/h tests were conducted at the T1 level and showed repeatability of setup and ATD responses. The 16 and 24 km/h tests at T1 and T6 were compared. Results indicated greater head rotation, neck extension moments and neck shear forces at T1 level impacts. For example, lower neck extension was 2.6 times and 3.8 times greater at T1 versus T6 impacts at 16 and 24 km/h, respectively.

Recently, side-by-side Recreational Off-Highway Vehicles (ROVs) have brought elements of the on-road vehicle occupant environment to the off-road trail-riding world. In general, ROV occupant protection during normal operation and in accident scenarios is provided predominately by a roll cage, seatbelts, contoured seats with seat backs, handholds, and other components. Typical occupant responses include both passive (inertial) and active (muscular) components. The objective of the current study was to evaluate and quantify these passive and active occupant responses during belted operation of an ROV on a closed course, as well as during 90-degree tip-over events. Passive occupant responses were evaluated using anthropomorphic test devices (ATDs) in 90-degree tip-overs simulated on a deceleration sled.

This research examines the effects of impactor characteristics on the calculated structural stiffness parameters A and B for the struck sides of late-model vehicles. This study was made possible by crash testing performed by the National Highway Traffic Safety Administration involving side impacts of the same vehicle line with both a rigid pole and with a moving deformable barrier. Twenty-nine crash test pairs were identified for 2018 model-year vehicles. Of 60 total tests, 49 were analyzed. Test data for 19 vehicles impacted in both modes resulted in A and B values considered to be valid. Classifying these 19 vehicles according to the categories defined by Siddall and Day, only Class 2 multipurpose vehicles were represented by enough vehicles (10) to search for trends within a given vehicle category. For these vehicles, more scatter in the results was observed in both A and B values for the MDB impacts compared to the pole impacts.

Spine degeneration can lower injury tolerance and influence injury outcomes in vehicle crashes. To date, limited information exists on the effect of age and sex on thoracic spine 3-dimensional geometry. The purpose of this study is to quantify thoracic spinal column and canal geometry using selected geometrical measurement from a large sample of CT scans. More than 33,488 scans were obtained from the International Center for Automotive Medicine database at the University of Michigan under Institutional Review Board approval (HUM00041441). The sample consisted of CT scans obtained from 31,537 adult and 1,951 pediatric patients between the ages of 0 to 99 years old. Each scan was processed semi-automatically using custom algorithms written in MATLAB (The Math Works, Natick, MA). Five geometrical measurements were collected including: 1) maximum spinal curvature depth (D), 2) T1-to-T12 vertical height (H), 3) Kyphosis Index (KI), 4) kyphosis angle, and 5) spinal canal radius.

The emergence of Plug-in hybrid electric vehicles (PHEVs) and electric vehicles (EVs) as a viable means of transportation has been coincident with the development of lithium-ion (Li-ion) battery technology and electronics. These developments have enabled the storage and use of large amounts of energy that were previously only possible with internal combustion engines. However, the safety aspects of using these large energy storage battery packs are a significant challenge to address. In addition, the rapid advances in electrode and electrolyte materials for Li-Ion batteries have made comparisons and ranking of safety parameters difficult because of the substantial variations in cell designs. In this work, we outline a method for quantifying the thermal safety aspects of Li-ion battery technologies using a Cone Calorimeter.

As micromobility devices (i.e., e-bikes, scooters, skateboards, etc.) continue to increase in popularity, there is a growing need to test these devices for varying purposes such as performance assessment, crash reconstruction, and design of new products. Although tests have been conducted across the industry for electric scooters (e-scooters), this paper describes a novel method for crash testing e-scooters with anthropomorphic test devices (ATDs) “riding” them, providing new sources for data collection and research. A sled fixture was designed utilizing a pneumatic crash rail to propel the scooters with an overhead gantry used for stabilization of the ATD until release just prior to impact. The designed test series included impacts with a 5.5-inch curb at varying incidence angles, a stationary vehicle, or a standing pedestrian ATD. Test parameter permutations included changing e-scooter tire sizes, impact speeds, and rider safety equipment.

Advanced Driver Assistive System (ADAS) technologies have been introduced as the automotive industry moves towards autonomous driving. One ADAS technology with the potential for substantial safety benefits is forward collision warning and mitigation (FCWM), which is designed to warn drivers of imminent front-end collisions, potentiate driver braking responses, and apply the vehicle's brakes autonomously. Although the proliferation of FCWM technologies can, in many ways, mitigate the necessity of a timely braking response by a driver in an emergency situation, how these systems affect a driver's overall ability to safely, efficiently, and comfortably operate a motor vehicle remains unclear. Exponent conducted a closed-course evaluation of drivers' reactions to an imminent forward collision event while driving an FCWM-equipped vehicle, either with or without a secondary task administered through a hands-free cell phone.

Seat strength has increased over the past four decades which includes a transition to dual recliners. There are seat collision performance issues with stiff ABTS and very strong seats in rear impacts with different occupant sizes, seating positions and physical conditions. In this study, eight rear sled tests were conducted in four series: 1) ABTS in a 56 km/h (35 mph) test with a 50th Hybrid III ATD at MGA, 2) dual-recliner ABTS and F-150 in a 56 km/h (35 mph) test with a 5th female Hybrid III ATD at Ford, 3) dual-recliner ABTS in a 48 km/h (30 mph) test with a 95th Hybrid III ATD leaning inboard at CAPE and 4) dual-recliner ABTS and Escape in 40 km/h (25 mph) in-position and out-of-position tests with a 50th Hybrid III ATD at Ford. The sled tests showed that single-recliner ABTS seats twist in severe rear impacts with the pivot side deformed more rearward than the stanchion side.

The debate surrounding roof deformation and occupant injury potential has existed in the automotive community for over 30 years. In analysis of real-world rollovers, assessment of roof deformation and occupant compartment space starts with the post-accident roof position. Dynamic movement of the roof structure during a rollover sequence is generally acknowledged but quantification of the dynamic roof displacement has been limited. Previous assessment of dynamic roof deformation has been generally limited to review of the video footage from staged rollover events. Rollover testing for the evaluation of injury potential has typically been studied utilizing instrumented test dummies, on-board and off-board cameras, and measurements of residual crush. This study introduces an analysis of previously undocumented real-time data to be considered in the evaluation of the roof structure's dynamic behavior during a rollover event.