Search Results

During the course of a fire and subsequent exposure to the environment, iron and low-carbon steels oxidize by two mechanisms: high temperature oxidation and atmospheric corrosion. Of particular interest to fire investigators are oxide properties and distribution that could be of use to better understand important characteristics of the fire such as the location the fire originated, the direction the fire traveled or even temperature versus time characteristics. This could be particularly valuable in cases where burn damage to combustible material, which is known to be an important indicator of fire origin, is so extensive that little if any material remains after the fire. However, there is little data in the literature that specifically addresses the utility of oxide properties in the context of fire investigations.

In some automotive electrical systems, it is advantageous to use power supplies and loads at two or more voltages. Often it is desirable to retain the single wire power architecture, with the car body providing the return circuit. A major difficulty in achieving this end is the matter of dealing with the possibility of a short circuit between feed wires at different voltages. It can be shown that source-side fuses cannot be relied upon to return the system to a safe state in all cases. Substantial effort was applied to this problem in the early years of the 21st century, but the results were less than completely satisfactory. Using entirely separate cable harnesses for each voltage, with physically separated routing, minimizes the risk of such a short occurring in the harness.

There is a limited amount of data currently available on the acceleration and braking performances of school buses. This paper analyzes the braking performance of various Type A and Type C school buses with hydraulic and air brakes. The effect of ABS and Non-ABS systems as well as driver experience is discussed. A comparison with passenger car braking performance is presented. The acceleration of a school bus is also presented. Evaluations of “normal” and “rapid” accelerations are presented for Type A and Type B buses. A comparison with commonly used acceleration values for various vehicles is presented.

Unintended acceleration events due to pedal misapplication have been shown to occur more frequently in older vs. younger drivers. While such occurrences are well documented, the nature of these movement errors is not well-characterized in common pedal error scenarios: namely, on-road, non-emergency stopping or slowing maneuvers. It is commonly assumed that drivers move in a ballistic or “direct hit” trajectory from the accelerator to the brake pedal. However, recent simulator studies show that drivers do not always move directly between pedals, with older drivers displaying more variable foot trajectories than younger drivers. Our study investigated pedal movement trajectories in older drivers ages 67.9 ± 5.2 years (7 males, 8 females) during on-road driving in response to variable traffic light conditions. Three different sedans and a pick-up truck were utilized.

Blunt impacts to the back of the torso can occur in vehicle crashes due to interaction with unrestrained occupants, or cargo in frontal crashes, or intrusion in rear crashes, for example. Six pendulum tests were conducted on the back of an instrumented 50th percentile male Hybrid III ATD (Anthropomorphic Test Device) to determine kinematic and biomechanical responses. The impact locations were centered with the top of a 15-cm diameter impactor at the T1 or at T6 level of the thoracic spine. The impact speed varied from 16 to 24 km/h. Two 24 km/h tests were conducted at the T1 level and showed repeatability of setup and ATD responses. The 16 and 24 km/h tests at T1 and T6 were compared. Results indicated greater head rotation, neck extension moments and neck shear forces at T1 level impacts. For example, lower neck extension was 2.6 times and 3.8 times greater at T1 versus T6 impacts at 16 and 24 km/h, respectively.

Recently, side-by-side Recreational Off-Highway Vehicles (ROVs) have brought elements of the on-road vehicle occupant environment to the off-road trail-riding world. In general, ROV occupant protection during normal operation and in accident scenarios is provided predominately by a roll cage, seatbelts, contoured seats with seat backs, handholds, and other components. Typical occupant responses include both passive (inertial) and active (muscular) components. The objective of the current study was to evaluate and quantify these passive and active occupant responses during belted operation of an ROV on a closed course, as well as during 90-degree tip-over events. Passive occupant responses were evaluated using anthropomorphic test devices (ATDs) in 90-degree tip-overs simulated on a deceleration sled.

Spine degeneration can lower injury tolerance and influence injury outcomes in vehicle crashes. To date, limited information exists on the effect of age and sex on thoracic spine 3-dimensional geometry. The purpose of this study is to quantify thoracic spinal column and canal geometry using selected geometrical measurement from a large sample of CT scans. More than 33,488 scans were obtained from the International Center for Automotive Medicine database at the University of Michigan under Institutional Review Board approval (HUM00041441). The sample consisted of CT scans obtained from 31,537 adult and 1,951 pediatric patients between the ages of 0 to 99 years old. Each scan was processed semi-automatically using custom algorithms written in MATLAB (The Math Works, Natick, MA). Five geometrical measurements were collected including: 1) maximum spinal curvature depth (D), 2) T1-to-T12 vertical height (H), 3) Kyphosis Index (KI), 4) kyphosis angle, and 5) spinal canal radius.

Advanced Driver Assistive System (ADAS) technologies have been introduced as the automotive industry moves towards autonomous driving. One ADAS technology with the potential for substantial safety benefits is forward collision warning and mitigation (FCWM), which is designed to warn drivers of imminent front-end collisions, potentiate driver braking responses, and apply the vehicle's brakes autonomously. Although the proliferation of FCWM technologies can, in many ways, mitigate the necessity of a timely braking response by a driver in an emergency situation, how these systems affect a driver's overall ability to safely, efficiently, and comfortably operate a motor vehicle remains unclear. Exponent conducted a closed-course evaluation of drivers' reactions to an imminent forward collision event while driving an FCWM-equipped vehicle, either with or without a secondary task administered through a hands-free cell phone.

Seat strength has increased over the past four decades which includes a transition to dual recliners. There are seat collision performance issues with stiff ABTS and very strong seats in rear impacts with different occupant sizes, seating positions and physical conditions. In this study, eight rear sled tests were conducted in four series: 1) ABTS in a 56 km/h (35 mph) test with a 50th Hybrid III ATD at MGA, 2) dual-recliner ABTS and F-150 in a 56 km/h (35 mph) test with a 5th female Hybrid III ATD at Ford, 3) dual-recliner ABTS in a 48 km/h (30 mph) test with a 95th Hybrid III ATD leaning inboard at CAPE and 4) dual-recliner ABTS and Escape in 40 km/h (25 mph) in-position and out-of-position tests with a 50th Hybrid III ATD at Ford. The sled tests showed that single-recliner ABTS seats twist in severe rear impacts with the pivot side deformed more rearward than the stanchion side.

Interest in rear-seat occupant safety has increased in recent years. Information relevant to rear-seat occupant interior space and kinematics are needed to evaluate injury risks in real-world accidents. This study was conducted to first assess the effect of size and restraint conditions, including belt misuse, on second-row occupant kinematics and to then document key clearance measurements for an Anthropomorphic Test Device (ATD) seated in the second row in modern vehicles from model years 2015-2020. Twenty-two tests were performed with non-instrumented ATDs; three with a 5th percentile female Hybrid III, 10 tests with a 10-year-old Hybrid III, and 9 tests with a 6-year-old Hybrid III. Test conditions included two sled bucks (mid-size car and sport utility vehicle (SUV)), two test speeds (56 and 64 km/h), and various restraint configurations (properly restrained and improperly restrained configurations). Head and knee trajectories were assessed.

There are established federal requirements and industry standards for frontal crash testing of motor vehicles. Consistently applied methods support reliability, repeatability, and comparability of performance metrics between tests and platforms. However, real world collisions are rarely identical to standard test protocols. This study examined the effects of occupant anthropometry and passive restraint deployment timing on occupant kinematics and biomechanical loading in a moderate-severity (approximately 30 kph delta-V) offset frontal crash scenario. An offset, front-to-rear vehicle-to-vehicle crash test was performed, and the dynamics of the vehicle experiencing the frontal collision were replicated in a series of three sled tests. Crash test and sled test vehicle kinematics were comparable. A standard or reduced-weight 50th percentile male Hybrid III ATD (H3-50M) or a standard 5th percentile female Hybrid III ATD (H3-5F) was belted in the driver’s seating position.

Three years of data from the Large Truck Crash Causation Study (LTCCS) were analyzed to identify accidents involving heavy trucks (GVWR >10,000 lbs.). Risk of rollover and ejection was determined as well as belt usage rates. Risk of ejection was also analyzed based on rollover status and belt use. The Abbreviated Injury Scale (AIS) was used as an injury rating system for the involved vehicle occupants. These data were further analyzed to determine injury distribution based on factors such as crash type, ejection, and restraint system use. The maximum AIS score (MAIS) was analyzed and each body region (head, face, spine, thorax, abdomen, upper extremity, and lower extremity) was considered for an AIS score of three or greater (AIS 3+). The majority of heavy truck occupants in this study were belted (71%), only 2.5% of occupants were completely or partially ejected, and 28% experienced a rollover event.

Airbag and seat belt pretensioner deployment characteristics depend on multiple factors, such as the magnitude, direction, and rate of vehicle deceleration as detected by vehicle crash sensors and evaluated by vehicle-specific algorithms. Frontal airbag and pretensioner deployments are likely to be commanded during frontal crash events with high initial vehicle deceleration typically associated with high vehicle change in velocity (delta-V). However, within a range of moderate changes in vehicle speeds, referred to as the “gray zone,” a vehicle-specific algorithm may or may not command deployment depending on crash pulse parameters and occupant sensing, among other items. Publicly available testing in the moderate-speed range is lacking and would be useful to evaluate the effects of airbag and pretensioner deployment on occupant kinematics and loading.

While nearly 50 percent of occupants in side-impact collisions are in vehicles that experience a velocity change (delta-V) below 15.0 kph (9.3 mph), full scale crash testing research at these delta-Vs is limited. Understanding occupant kinematics in response to these types of side impacts can be important to the design of side-impact safety countermeasures, as well as for evaluating potential interactions with interior vehicle structures and/or with other occupants in the vehicle. In the current study, two full-scale crash tests were performed utilizing a late-model, mid-size sedan with disabled airbags. The test vehicle was impacted by a non-deformable moving barrier on the driver side at an impact speed of 10.0 kph (6.2 mph) in the first test and then on the passenger side at an impact speed of 21.6 kph (13.4 mph) in the second test, resulting in vehicle lateral delta-Vs of 6.1 kph (3.8 mph) and 14.0 kph (8.7 mph), respectively.

Low- to moderate-speed motor vehicle collisions are a common crash type and are sometimes associated with injury complaints. Understanding occupant motion (kinematics) in response to low- and moderate-speed motor vehicle collisions is important for evaluating occupant interactions with interior vehicle structures, including the restraint systems, with the ultimate goal of assessing injury potential. Furthermore, quantitative occupant kinematic data from full-scale crash testing of late-model passenger vehicles is limited for collisions at low- to moderate-speeds. The current study reports kinematic data from full-scale frontal and rear-end crash tests of late-model, mid-size sedans with delta-Vs ranging from 6.0 to 19.0 kph (3.7 to 11.8 mph) and 5.6 to 19.5 kph (3.5 to 12.1 mph), respectively. For each test vehicle, the motion of a Hybrid III 50th-percentile male anthropomorphic test device (ATD) restrained in the driver seat was recorded using high-speed onboard video.

Field data was analyzed on second-row children in front, side and rear impacts to study fatality trends by model year (MY) and calendar year (CY) with 1980-2020 MY vehicles. The different MY and CY perspectives show changes in rates that are useful for setting priorities for second-row child safety in rear impacts. 1990 to 2019 FARS was queried to assess the number of fatally injured and non-ejected second-row children (0-15 years old) in crashes without fires. The children included outboard occupants seated behind an occupied front seat and center occupants. The data was analyzed for rear, front and side impacts to assess crash frequency. 1990-2015 POLK was queried to assess exposure of registered vehicles and estimate a fatality rate. The FARS and POLK data were sub-grouped by MY of the vehicle and CY of the crash. There were 2.8-times more fatally injured children in frontal crashes than in the rear crashes. The ratio of frontal and rear crashes varied with CY sub-groups.

Safety-critical systems in most modern applications are designed in a way such that they provide a fail-safe operation when a fault occurs, to pose minimum risk to the user. As these systems become more sophisticated with increased functionality, it is important that their design incorporates functional safety concepts which entail detection of a potential harmful condition that prompts a corrective action to prevent hazardous events. In this paper, we discuss the significance of safety-critical systems along with the implementation of fail-safe designs in these systems. We also aim to provide an overview of functional safety as addressed in some of the industry standards and through a case study demonstrate how the concepts can be used when developing a safety-critical system.

Rear-end impacts are the most common crash scenario in the United States. Although automated vehicle (AV) technologies, such as frontal crash warning (FCW) and automatic emergency braking (AEB), are mitigating and preventing rear-end impacts, the technology is only gradually being introduced and currently has only limited effectiveness. Accordingly, there is a need to evaluate the current state of passive safety technologies, including the performance of seatbacks and head restraints. The objective of this study was to examine trends in head and neck loading during rear impact testing in new vehicle models over the prior decade. Data from 601 simulated rear impact sled tests (model years 2004 to 2018) conducted as a part of the Insurance Institute for Highway Safety (IIHS) Vehicle Seat/Head Restraint Evaluation Protocol were obtained.

The operational safety of automated driving system (ADS)-equipped vehicles (AVs) needs to be quantified for an understanding of risk, requiring the measurement of parameters as they relate to AVs and human driven vehicles alike. In prior work by the Institute of Automated Mobility (IAM), operational safety metrics were introduced as part of an operational safety assessment (OSA) methodology that provide quantification of behavioral safety of AVs and human-driven vehicles as they interact with each other and other road users. To calculate OSA metrics, the data capture system must accurately and precisely determine position, velocity, acceleration, and geometrical relationships between various safety-critical traffic participants. The design of an infrastructure-based system that is intended to capture the data required for calculation of OSA metrics is addressed in this paper.

This study assesses the exposure distribution and injury rate (MAIS 4+F) to front-outboard non-ejected occupants by crash severity, belt use and head restraint type and damage in rear impacts using 1997-2015 NASS-CDS data. Rear crashes with a delta V <24 km/h (15 mph) accounted for 71% of all exposed occupants. The rate of MAIS 4+F increased with delta V and was higher for unbelted than belted occupants with a rate of 11.7% ± 5.2% and 6.0% ± 1.5% respectively in 48+ km/h (30 mph) delta V. Approximately 12% of front-outboard occupants were in seats equipped with an integral head restraint and 86% were with an adjustable head restraint, irrespective of crash severity. The overall injury rate was 0.14% ± 0.05% and 0.22% ± 0.06%, respectively. It was higher in cases where the head restraint was listed as “damaged”. Thirteen cases involving a lap-shoulder belted occupant in a front-outboard seat in which “damage” to the adjustable head restraint was identified.