Search Results

A new method is demonstrated for rating the “severity” of a hypoid gear set duty cycle (revolutions at torque) using the intercept of T-N curve to support gearset selection and sizing decision across vehicle programs. Historically, it has been customary to compute a cumulative damage (using Miner's Rule) for a rotating component duty cycle given a T-N curve slope and intercept for the component and failure mode of interest. The slope and intercept of a T-N curve is often proprietary to the axle manufacturer and are not published. Therefore, for upfront sizing and selection purposes representative T-N properties are used to assess relative component duty cycle severity via cumulative damage (non-dimensional quantity). A similar duty cycle severity rating can also be achieved by computing the intercept of the T-N curve instead of cumulative damage, which is the focus of this study.

Understanding planetary gear efficiency is more involved than understanding efficiency of external gears because of the recirculating power that is inherent in planetary gear operation. There have been several publications going back several decades on this topic. However, many of these publications are mathematical in their approach and tend to be overlooked by practicing engineers. This paper brings a new, more visual and more intuitive approach to the problem. It uses lever diagrams, which have been a standard tool in the transmission engineer’s arsenal for almost four decades, to visualize the power flow and develop analytical expressions for the efficiency of simple and compound planetary gears. It then extends the approach to more complex gear trains.

For a light duty truck, the frame is a structural system and it must go through a series of proving ground events to meet fatigue performance requirement. Nowadays, in order to meet stringent CAFE standards, auto manufacturers are seeking to keep the vehicle weight as light as possible. The weight reduction on the frame is a challenging task as it still needs to maintain the strength, safety, and durability fatigue performance. CAE fatigue simulation is widely used in frame design before the physical proving ground tests are performed. A typical frame durability fatigue analysis includes both the base metal fatigue analysis and seam weld fatigue analysis. Usually the gauges of the frame components are dictated by the seam weld fatigue performance so opportunities for weight reduction may exist in areas away from the welds. One method to reduce frame weight is to cut lightening holes in the areas that have little impact on the frame fatigue performance.

The front-end air flow conditions have a substantial impact on the cool down performance of a vehicle Heating, Ventilation and Air-Conditioning (HVAC) system. The performance of a mobile HVAC system is analyzed by conducting tests on the vehicle in a drive cell, subjecting it to different drive cycles. This now can be done virtually using system level simulation or one-dimensional (1D) tools. Target values for condenser air inlet velocity and temperature for these HVAC performance focused drive cycles needs to be established during the development phase to meet the cool down functional objectives of the vehicle. Thus, in the early stages of development, 1D tools play a major role. Condenser air flow should be sufficient and the temperature should be as low as possible at different vehicle operating conditions to have good air-conditioning (AC) performance.

This paper describes a CAE fatigue life prediction technique for a tailgate on pickup truck cargo box with inertial forces and moments applied at mass center of the tailgate as input loads. The inertial forces and moments are calculated from the accelerations measured at the corners of the tailgate as the truck is being driven over a durability schedule at the test proving grounds. All the dynamic responses of the tailgate on cargo box, including any dynamic interactions at the pivot joints between the tailgate and box sides, are captured in the acquired data and also in the inertial forces and moments computed at the mass center. Correspondingly, all the dynamic responses are included in the CAE fatigue life predictions. The dynamic interactions at the pivot joints are simulated by using two identical CAE models, one with lateral translational constraint applied at the left pivot only and the other at the right pivot only.

Design for Six Sigma (DFSS) is an essential tool and methodology for innovation projects to improve the product design/process and performance. This paper aims to present an application of the DFSS Taguchi Method for an automotive/vehicle component. High-Pressure Vacuum Assist Die Casting (HPVADC) technology is used to make Cast Aluminum Front Shock Tower. During the vehicle life, Shock Tower transfers the road high impact loads from the shock absorber to the body structure. Proving Ground (PG) and washout loads are often used to assess part strength, durability life and robustness. The initial design was not meeting the strength requirement for abusive washout loads. The project identified eight parameters (control factors) to study and to optimize the initial design. Simulation results confirmed that all eight selected control factors affect the part design and could be used to improve the Shock Tower's strength and performance.

This paper proposes a method to evaluate the sensitivity of the perceived quality of a panel interface design to variation in the measurements of fit and finish. The novelty of this approach is in the application of the concept of utility to fit and finish. The significance is in the ability to evaluate alternative designs with regard to perceived quality long before time and money are spent on their realization. In the automotive industry “fit and finish” is the term applied to the precision of the alignment of one part to another. Fit and finish gives the buyer a sense of the overall quality of the vehicle purely from an aesthetic perspective. Fit and finish is usually evaluated by the manufacturer through dimensional measurements of the gap and flushness conditions between panels.

Automotive companies are studying to add extra value in their vehicles by enhancing powertrain sound quality. The objective is to create a brand sound that is unique and preferred by their customers since quietness is not always the most desired characteristic, especially for high-performance products. This paper describes the process of developing a brand powertrain sound for a high-performance vehicle using the DFSS methodology. Initially the customer's preferred sound was identified and analyzed. This was achieved by subjective evaluations through voice-of-customer clinics using vehicles of similar specifications. Objective data were acquired during several driving conditions. In order for the design process to be effective, it is very important to understand the relationship between subjective results and physical quantities of sound. Several sound quality metrics were calculated during the data analysis process.

Many chassis and powertrain components in the transportation and automotive industry experience multi-axial cyclic service loading. A thorough load-history leading to durability damage should be considered in the early vehicle production steps. The key feature of rubber fatigue analysis discussed in this study is how to define local critical location strain time history based on nominal and complex load time histories. Material coupon characterization used here is the crack growth approach, based on fracture mechanics parameters. This methodology was utilized and presented for a truck engine mount. Temperature effects are not considered since proving ground (PG) loads are generated under isothermal high temperature and low frequency conditions without high amounts of self-heating.

Geometry Tree is a term describing the product assembly structure and the manufacturing process for the product. The concept refers to the assembly structure of the final vehicle (the Part Tree) and the assembly process and tools for the final product (the Process Tree). In the past few years, the Geometry Tree-based quality process was piloted in the FCA US LLC assembly plants and has since evolved into a standardized quality control process. In the Part Tree process, the coordinated measurements and naming convention are enforced throughout the different levels of detailed products to sub-assemblies and measurement processes. The Process Tree, on the other hand, includes both prominently identified assembly tools and the mapping of key product characteristics to key assembly tools. The benefits of directly tying critical customer characteristics to actual machine components that have a high propensity to influence them is both preventive and reactive.

Automotive AC systems are typically either single unit or dual unit systems, while the dual unit systems have an additional rear evaporator. The refrigerant evaporates inside these heat exchangers by taking heat and condensing the moisture from the recirculated or fresh air that is being pushed into the car cabin by air blowers. This incoming cold air in turn brings the cabin temperature and humidity to a level that is comfortable for the passengers. These HVAC units have their own thermal expansion valve to set the refrigerant flow, but both are connected to the main AC refrigerant loop. The airflows, however, are controlled independently for front and rear unit that can affect the temperature and amount of air coming into the cabin from each location and consequently the overall cabin cool-down performance.

Upper frame deflection of automobile doors is a key design attribute that influences structural integrity and door seal performance as related to NVH. This is a critical customer quality perception attribute and is a key enabler to ensure wind noise performance is acceptable. This paper provides an overview of two simulation methodologies to predict door upper frame deflection. A simplified simulation approach using point loads is presented along with its limitations and is compared to a new method that uses CFD tools to estimate aerodynamic loads on body panels at various vehicle speeds and wind directions. The approach consisted of performing external aerodynamic CFD simulation and using the aerodynamic loads as inputs to a CAE simulation. The details of the methodology are presented along with results and correlation to experimental data from the wind tunnel.

The LEV IV FTP PM limit in the recently approved CARB ACC II regulations for passenger cars and light duty trucks will be 1 mg/mile starting in 2025. Gravimetric PM measurement at these levels is very challenging as the net mass of PM on the filter in full flow tunnel testing ranges between 8 to 32 micrograms depending on amount of dilution. This is approaching tunnel background levels which, in combination with filter handling, static charge removal and microbalance instability, compounds the uncertainty. One major source of the uncertainty at these low levels is the tunnel contamination resulting in high variability from test to test and cell to cell. This tunnel background is mostly HC artifact which cannot be easily controlled and can be significantly higher than the 5-μg CFR allowable correction limit in some test cells.

ISO/SAE 21434 [1] Final International Standard was released September 2021 to great fanfare and is the most prominent standard in Automotive Cybersecurity. As members of the Joint Working Group (JWG) the authors spent 5 years developing the 84 pages of precise wording acceptable to hundreds of contributors. At the same time the auto industry had been undergoing a metamorphosis probably unmatched in its hundred-year history. A centerpiece of the metamorphosis is the adoption of the Agile development method to meet market demands for time-to-market and flexibility of design. Unfortunately, a strategic decision was made by the JWG to focus ISO/SAE 21434 on the V-Model method. Agile does not break ISO/SAE 21434. Agile is a framework that can be adapted to suit any process. In the end the goals are the same regardless of development method; security by design must be achieved.

Automobiles have a high degree of mechanical and electrical complexity. However, product complexity has the accompanying effect of requiring high levels of design and process oversight. The net result is a product creation process which is prone to creating failures. These failures typically have their origin in an overall lack of complete understanding of the system in terms of materials, geometries and energy flows. Despite all of the engineering intentions, failures are inevitable, common, and must be dealt with accordingly. In the worst case, if a failure manifests itself into an observable failure the customer may have a negative experience. Therefore, it is imperative that design engineers, suppliers along with reliability professionals be able to assess the design risk. One approach to assess risk is the use of degradation analysis. Degradation analysis often provides more information than failure time data for assessing reliability and predicting the remnant life of a system.

As CAFE requirements increase, automotive OEMs are pursuing innovative methods to lightweight their Body In Whites (BIWs). Within FCA US, this lightweighting research and development activity often occurs through Decoupled Innovation projects. A Decoupled Innovation team comprised of engineers from the BIW Structures Group, in collaboration with Tier 1 supplier Magna Exteriors, sought to re-design a loadbearing component on the BIW that would offer significant weight savings when the current steel component was replaced with a carbon fiber composite. This paper describes the design, development, physical validation and partnership that resulted in a composite Rear Package Shelf Assembly solution for a high-volume production vehicle. As the CAFE requirements loom closer and closer, these innovation-driven engineering activities are imperative to the successful lightweighting of FCA US vehicles.

Several powertrain noise phenomena have been studied over the years. Sound quality metrics, like loudness, sharpness, modulation, and tonality, among others, have been developed to characterize powertrain noises. While these readily available metrics work well on steady state and some transient noises, they do not correlate directly with subjective impressions. Moreover, it is difficult to assign a meaningful single rating for time varying noises that may also be associated with simultaneous variations in frequency content. This paper summarizes the process of creating a vehicle level objective metric and its application to blind noise samples to verify correlation with subjective impressions, particularly in association with clatter noise at moderate engine speeds (2000-3500 rpm) with light to moderate throttle tip-ins.

Cargo box is one of the indispensable structures of a pickup truck which makes it capable of transporting heavy cargo weights. This heavy cargo weight plays an important role in durability performance of the box structure when subjected to road load inputs. Finite element representation for huge cargo weight is always challenging, especially in a linear model under dynamic proving ground road load durability analysis using a superposition approach. Any gap in virtual modeling technique can lead to absurd cargo box modes and hence durability results. With the existing computer aided engineering (CAE) approach, durability results could not correlate much with physical testing results. It was crucial to have the right and robust CAE modeling technique to represent the heavy cargo weight to provide the right torsional and cargo modes of the box structure and in turn good durability results.

Dimensional problems for punched holes on a sheet metal stamping part include being undersized and oversized. Some important relationships among tools and products, such as the effect of conical punch tip angle, are not fully understood. To study this effect, sheets of AA6016 aluminum and BH210 steel were punched by punches with different conical tip angles. The test method and test results are presented. The piercing force and withdrawing force when using conical punches were also studied. The results indicate that the oversize issue for a punched hole in a stamped panel is largely due to the combination of the conical tip effect and the stretching-release effect.

Dimensional accuracy of punched hole is an essential consideration for high-quality sheet metal forming. An out-of-shape hole can give rise to manufacturing issues in the subsequent production processes thus inducing quality defects on a vehicle body. To understand the effects of punch shapes and cutting configurations on punched hole diameter deviations, a systematical experimental study was conducted for multiple types of AHSS (DP1180, DP980, DP590) and one mild steel. Flat, conical and rooftop punches were tested respectively with three cutting clearances on each material. The measurement results indicated different diameter enlargement modes based on the punch profiles, and dimensional discrepancies were found to be more significant with the stronger materials and higher cutting clearance. To uncover the mechanism of punched hole enlargement, a series of finite element simulations were established for numerical investigation.