Search Results

Voice communications are crucial to safe and efficient air traffic operations. Controllers are required to use standard phraseology, and pilots are encouraged to use it when talking to controllers. Incomplete or inaccurate communications were implicated in mishaps such as the Tenerife accident. This research examined the frequency of phraseology deviations in a sample of 5,000 transmissions from 3 terminal facilities. The Aviation Topics-Speech Acts Taxonomy (ATSAT) was used to develop baseline data and analyze controller/pilot communications. Clearance instructions were transmitted most frequently and they contained a higher percentage of deviations from standard phraseology than any other speech act category. Identification of the types of errors typically associated with specific miscommunications could result in implementing new training approaches that ensure a higher compliance with standard procedures and improve standard phraseology usage.

Weather is a major cause of aircraft accidents and incidents and the single largest contributor to air traffic system delays. Through improvements in the knowledge of current weather conditions and reliable forecasts, the Federal Aviation Administration (FAA) can improve aviation safety, increase system capacity, and enhance flight planning and fuel efficiency. The FAA has established an Aviation Weather Research (AWR) program to address specific requirements for weather support to aviation by providing the capability to generate more accurate and accessible weather observations, warnings, and forecasts and also by increasing the scientific understanding of atmospheric processes that spawn aviation weather hazards. The goal of AWR is to provide meteorological research that leads to the satisfaction of specific aviation weather requirements.

Hazardous atmospheric icing conditions occur at sub-zero temperatures when droplets come into contact with aircraft and freeze, degrading aircraft performance and handling, introducing bias into some of the vital measurements needed for aircraft operation (e.g., air speed). Nonetheless, government regulations allow certified aircraft to fly in limited icing environments. The capability of aircraft sensors to identify all hazardous icing environments is limited. To address the current challenges in aircraft icing detection and protection, we present herein a platform designed for in-flight testing of ice protection solutions and icing detection technologies. The recently developed Platform for Ice-accretion and Coatings Tests with Ultrasonic Readings (PICTUR) was evaluated using CFD simulations and installed on the National Research Council Canada (NRC) Convair-580 aircraft that has flown in icing conditions over North East USA, during February 2022.

“As we handle more operations and passengers in the air, we must make certain we have the capacity to handle increased traffic on the ground.” - Jane Garvey, FAA Administrator (4/20/98) The FAA Technical Center (Aviation System Analysis and Modeling Branch, ACT-520) has been responsive to the FAA Airport Capacity Program customers for the past 22 years, developing, testing, and applying airfield and airspace simulation models. More than 90 capacity studies have been completed with ACT-520 personnel contributing their technical expertise to the Airport Design Teams. The teams are comprised of FAA personnel, airport operators, air carriers, other airport users and aviation industry representatives at major airports throughout the US. Initial studies focused on modeling airport operations from final approach, taxi, gate operations and departure processing. Later in the program, local airspace studies were included in some airport study efforts.

Average continuous flow rates for each type of aircraft exit were examined in 89 full-scale evacuation demonstrations. Passengers tend to form continuous lines at available exits when evacuating an airplane. The study concludes that, with rare exception, the passenger rates of egress from the same type exit on different make and model airplanes are not significantly different. Passenger cabin configuration, seat pitch, and aisle width have no significant bearing on the egress rates provided the aircraft certification requirements for minimum aisle width and exit accessibility are met. Injuries resulting from actual emergency evacuations and evacuation demonstrations are also examined.

Area navigation offers a means of establishing an air route system without the constraints entailed in flying toward or away from the signal source. In terminal areas, an area navigation system of routes, combined with ATC computer-aided sequencing and airborne collision-avoidance technology, offers possibilities for establishing future methods of moving high volumes of traffic on and off a complex of multiple parallel runways. Such a system would reduce air-ground communications and controller workloads which are serious limiting factors in today's system. In the en route system, the use of area navigation will result in more efficient utilization of airspace, although regimentation of traffic will continue to be necessary in areas of high traffic density. An area navigation system, based on VOR/DME inputs is possible in the near future.

Monitoring head accelerations as an indicator of possible brain injury may lead to faster identification of injury and treatments. This study investigates the skull-coupling of a tri-axial accelerometer mounted to a back molar and compares it with a tri-axial accelerometer inserted in the boney ear canal. These tri-axial accelerometers were mounted to three post mortem human surrogate (PMHS) skulls, and compared with a rigid, skull-mounted laboratory sensor reference cube. Each specimen was subjected to both a high-g loading from a vertical drop tower and a low frequency cyclic loading from a shaker device. The specimens were subjected to an approximate 150g input acceleration on the drop tower, and up to 10g at a frequency of 9Hz on the shaker device. Each specimen was tested on all three of the anatomical axes on both the drop tower and the cyclic shaker.

Since the first airplane was certified in 1927, the standard configuration has been with the main lifting surface or surfaces forward of the stabilizing surface. Although some of the advantages of the canard configuration were recognized quite early - by the Wright Brothers, for example - canard surfaces have been used to date only as additional control surfaces on some military airplanes, and on some amateur built airplanes. As a result, the Airworthiness Regulations of Reference 1 address only tail aft configurations. When FAA was first approached regarding certification of a canard configured small airplane, an FAA/Industry Empennage Loads Working Group was formed to develop technical proposals for the necessary rule changes and policy. The concerns addressed by this working group are discussed in the following sections.

Microprocessor technology is allowing functions in aircraft to be implemented to a greater degree by digital process control than by conventional mechanical or electromechanical means. A review of this technology indicates a need for updated certification criteria. A high level of commitment to the technology such as fly-by-wire is completely beyond the scope of existing certification criteria. This paper emphasizes the areas of software validation levels, increased concern with basic power system qualification, and increased environmental concerns for electromagnetic interference and lightning.

Powered-lift aircraft, such as the V-22 tilt-rotor, are likely to spin-off a civil version. The present FAA airworthiness certification standards are not considered to be adequate for these unique aircraft. The FAA has drafted certification criteria and held a public conference to review the draft and identify significant technical certification issues that require further effort to establish correct standards for powered-lift aircraft. Some of those issues are discussed.

Important provisions are highlighted with respect to the additional airworthiness standards being considered by the Federal Avaiation Administration for small airplanes capable of carrying more than 10 occupants which are intended for use in air taxi and commercial operations. Information is presented on the background leading to these provisions and on their impact on manufacturers and operators. These new standards would result in a significant increase in the level of safety which is more commensurate with the class of operation, the increased occupant capacity, and the expanded volume of operations anticipated for these airplanes.

NASA's Deep Space Network (DSN) uses high-power transmitters on its large antennas to communicate with spacecraft of NASA and its partner agencies. The prime reflectors of the DSN antennas are parabolic, at 34m and 70m in diameter. The DSN transmitters radiate Continuous Wave (CW) signals at 20 kW - 500 kW at X-band and S-band frequencies. The combination of antenna reflector size and high frequency results in a very narrow beam with extensive oscillating near-field pattern. Another unique feature of the DSN antennas is that they (and the radiated beam) move mostly at very slow sidereal rate, essentially identical in magnitude and at the opposite direction of Earth rotation.

This paper presents a description of several Federal Aviation Administration (FAA) incident data systems that contain information on events which result primarily from human error. These data systems include reports of near midair collisions, operational errors, pilot deviations, and events reported through the Aviation Safety Reporting System (ASRS). Over 17,000 incident reports are received and stored in these data bases annually. This paper discusses the information content of the data bases, reporting procedures, system limitations, proposed improvements, and uses of the data.

Unmanned Aircraft Systems (UAS) emerge as a viable, operational technology for potential civil and commercial applications in the National Airspace System (NAS). Although this new type of technology presents great potential, it also introduces a need for a thorough inquiry into its safety impact on the NAS. This study presents a systems-level approach to analyze the safety impact of introducing a new technology, such as UAS, into the NAS. Utilizing Safety Management Systems (SMS) principles and the existing regulatory structure, this paper outlines a methodology to determine a mandatory safety baseline for a specific area of interest regarding a new aviation technology, such as UAS Sense and Avoid. The proposed methodology is then employed to determine a baseline set of hazards and causal factors for the UAS Sense and Avoid problem domain and associated regulatory risk controls.

Materials are available for preventing or retarding aircraft cabin fires involving urethane foam seat cushions. Realistic fire tests performed in a wide-body test article demonstrate that some in-flight and ramp fires can be prevented, and that the allowable time for safe evacuation can be significantly extended during a survivable postcrash fuel fire, when the urethane foam seat cushion is covered by a “blocking layer” material.

Although Unmanned Aircraft Systems (UAS) have now for some time been used in segregated airspace where separation from other air traffic can be assured, potential users have interests to deploy UAS in non segregated airspace. Recent technological and operational improvements give reason to believe that UAS safety and performance capabilities are maturing. But the skies can only really open up to UAS when there is an agreed upon UAS safety policy with commonly accepted UAS Safety Risk Management (SRM) processes enabling to show that the risks related to UAS operations in all the different airspace classes can be adequately controlled. The overall objective is to develop a UAS SRM framework, supporting regulators and applicants through provision of detailed guidelines for each SRM step to be conducted, including 1) system description, 2) hazard identification, 3) risk analysis, 4) risk assessment, 5) risk treatment.

In 2021 the Federal Aviation Administration in collaboration with the National Research Council of Canada performed research on altitude ice crystal icing of aircraft engines using the modular compressor rig, ICE-MACR, in an altitude wind tunnel. The aim of the research campaign was to address research needs related to ice crystal icing of aircraft engines outlined in FAA publication Engine Ice Crystal Icing Technology Plan with Research Needs. This paper reports the findings on ice accretion from a configuration of ICE-MACR with two compression stages. Inherent in two-stage operation is not just additional fracturing and heating by the second stage but also higher axial velocity and potentially greater centrifuging of particles. These factors influence the accretion behavior in the test article compared to single stage accretion.

The Ice Crystal Environment Modular Axial Compressor Rig (ICE-MACR) was developed by the National Research Council of Canada (NRC) with support from the Federal Aviation Administration (FAA) in response to the need to understand ice crystal icing of aircraft engines at high altitudes. Icing wind tunnel tests on static hardware lack some of the real physics of turbofan compressor such as centrifuging and fracturing of particles, and melting of particles due to compression heating, heat transfer through a casing wall, as well as annular geometry effects. Since the commissioning of ICE-MACR in 2019 new insights have been gained on the physics behind ice crystal icing of turbofan engines. Additionally, the results of various test campaigns have been used to validate engine ice accretion numerical codes. This paper summarizes the key insights into ICI of turbofans gained from the ICE-MACR to date.

High Ice Water Content (HIWC) has been identified as a primary causal factor in numerous engine events over the past two decades. Previous attempts to develop a remote detection process utilizing modern commercial radars have failed to produce reliable results. This paper discusses the reasons for previous failures and describes a new technique that has shown very encouraging accuracy and range performance without the need for any modifications to industry’s current radar design(s). The performance of this new process was evaluated during the joint NASA/FAA HIWC RADAR II Flight Campaign in August of 2018. Results from that evaluation are discussed, along with the potential for commercial application, and development of minimum operational performance standards for future radar products.