Search Results

In this article we present a design of a new miniaturized sensor with the capacity to measure exhaust particle concentrations on board vehicles and engines. The sensor is characterized by ultra-fast response time, high sensitivity, and a wide dynamic range. In addition, the physical dimensions of the sensor enable its placement along the exhaust line. The concentration response and temporal performance of a prototype sensor are discussed and characterized with aerosol laboratory test measurements. The sensor performance was also tested with actual engine exhaust in both chassis and engine dynamometer measurements. These measurements demonstrate that the sensor has the potential to meet and even exceed any requirements around the world in terms of on-board diagnostic (OBD) sensitivity and frequency of monitoring.

There is increasing international interest in collision avoidance and more recently in safety systems for ‘Vulnerable Road Users’ (VRUs). The aim of the ‘Advanced Protection for Vulnerable Road Users’ (APVRU) project was to develop a sensor system capable of detecting VRUs, distinguishing them from the road environment, tracking their position and predicting potential impacts with the vehicle. Our fusion of sensor data from multiple, short range, high accuracy, pulse radar units and a low-resolution passive infrared sensor array serves to eliminate the majority of clutter by negating false triangulation combinations, whilst ensuring that only thermally distinct moving targets are considered. The intention is that a derivative of the sensor system may eventually provide the technological link between VRU detection and a driver warning, collision avoidance and/or the activation of a safety system on the vehicle (external airbags).

The Pegasor Particle Sensor (PPS) has been earlier presented by Ntziachristos et al. (SAE Paper 2011-01-0626) as a novel small and robust instrument that can be directly installed in the exhaust line to measure exhaust particles without any dilution. The instrument is based on the electrical detection of aerosol. It is increasingly being used to measure exhaust particles from engines and vehicles with different exhaust configurations. In this study, a number of tests have been conducted using two sensors in parallel, one directly installed in the tailpipe and one installed in the CVS, side by side to the PM sampling filter. Aim of the study was to make recommendations on the proper use of the sensor and to check how the sensor signal compares to particulate mass, soot concentration, and particle number. A first finding is that external heating has to be provided to the sensor to avoid condensation.

Calibrating a vehicle’s powertrain for dynamic operation needs to focus on efforts to mitigate the risks of thermal overload which may arise in the stator or rotor components of an e-motor. Risks also may arise for expected NVH or durability targets, with torque and torque “oscillations” acting as primary sources for the vehicles’ NVH behavior. Both topics, temperature measurement of stator and rotor as well as dynamic torque measurements of the powertrain’s drive shaft are addressed with examples demonstrating the sensors applications in normal test bed and vehicle configurations.

Modelling of conflicts between cars and pedestrians is presented in the paper. The model looks at how the velocities and distances change over the time between the pedestrian when first sensed and a potential impact, taking account of how the vehicle speed may be changing due to braking, wheel slip etc. Further work is outlined looking at the probability of conflict resolution behaviour by drivers and pedestrians. The paper also reviews current sensor technology appropriate for detecting pedestrians in front of a moving vehicle. A sensor system is required that responds to the road environment in real-time, and intelligently analyses the data so as to predict potential collisions and determine the nature of such collisions. A detection system combining radar detection with passive infrared detection and classification is proposed as a possible solution, meeting the requirements determined by conflict modelling and a review of the operating environment.

Fast charging of batteries at cold conditions faces the challenge of promoting undesired cell degradation phenomena such as lithium plating. The occurrence of lithium plating is strongly related to local surface potentials and temperatures involving the scales of the electrode surface, the unit cell and the entire module or pack. A multi-scale, multi-domain model is presented, enhancing a Newman based unit cell model with consistent models for heat generation and lithium plating and integrating this 1D+1D approach into a thermal 3D model on module level. The basic equations are presented and three different plating models from literature are discussed. The thermal model is assessed in open-loop simulations and the different plating approaches are compared in charge/discharge simulations at different operating conditions. The full multi-scale, multi-domain model is applied as a virtual sensor for model-based control of fast charging at cold conditions.

This work elaborates the transferability of electrode diffusion coefficients gained from fitting procedures in frequency domain to an electrochemical battery model run in time domain. An electrochemical battery model of an NMC622 half-cell electrode is simulated with sinusoidal current excitations at different frequencies. The current and voltage signals are analyzed in frequency domain via Nyquist and Bode plots. The frequency domain analysis of time domain simulations is applied to assess the numerical convergence of the simulation and the sensitivity on particle diameter, electrode and electrolyte diffusion coefficients. The simulated frequency spectra are used to fit the electrode diffusion coefficient by means of different electrical equivalent circuit models and the electrochemical battery model itself. The fitted diffusion coefficients from the different electrical equivalent circuit models deviate by one order of magnitude from the a priori known reference data.

The proposed Euro 7 emission standard foresees that the emission behaviour of Euro 7 vehicles is monitored via an on-board monitoring (OBM) system. In Euro 7 vehicles, OBM systems will monitor the emissions of nitrogen oxides (NOX), ammonia (NH3) and particulate matter (PM) for every trip through a combination of measured and modelled data. Sensors employed to support on-board diagnostics (OBD) in current vehicles may be used to support OBM. According to the Euro 7 OBM concept presented in this paper, OBM will serve a dual purpose: the first is to warn the user of a vehicle about the need to perform repairs on the engine or the pollution control systems when these are needed. If these repairs are not performed in a timely manner, the OBM system will be able to ultimately prevent engine restart, akin to the existing low-reagent driver warning system in some compression ignition vehicles. The second purpose of OBM is to monitor the compliance of vehicle types with the emission limits.

The parameterization of the electrochemical pseudo-two-dimensional (P2D) model plays an important role as it determines the acceptance and application range of subsequent simulation studies. Electrochemical impedance spectroscopy (EIS) is commonly applied to characterize batteries and to obtain the exchange current density and the solid diffusion coefficient of a given electrode material. EIS measurements performed with frequencies ranging from 1 MHz down to 10 mHz typically do not cover clearly isolated solid state diffusion processes of lithium ions in positive or negative electrode materials. To extend the frequency range down to 10 μHz, the distribution function of relaxation times (DRT) is a promising analysis method. It can be applied to time-domain measurements where the battery is excited by a current pulse and relaxed for a certain period.

Fused filament fabrication (FFF) 3D printing technology, one of the most accessible additive manufacturing technologies, can be used to create sensors based on different sensing principles, e.g.: capacitance, inductance, piezoelectricity, piezoresistivity. Piezoresistivity (strain-dependent electrical resistivity) has been predominantly used for the creation of static/quasistatic 3d printed sensors with relatively low sensitivity. This study researches the possibilities of a single-process 3d printing of a piezoresistive accelerometer. Initially, the methods for the axial and cross-axial identification of the piezoresistive properties are discussed. It is shown that the sensitivity is highly dependent on the printing parameters, especially the printing track orientation vs the mechanical load orientation. The research on the sensitivity of a 3D printed piezoresistive structure is extended with an inertial mass-based accelerometer design.