Search Results

An integrated engineering approach using computer modeling, laboratory and vehicle testing enabled the Ford GT engineering team to achieve supercar thermal management performance within the aggressive program timing. Theoretical and empirical test data was used during the design and development of the engine cooling system. The information was used to verify design assumptions and validate engineering efforts. This design approach allowed the team to define a system solution quickly and minimized the need for extensive vehicle level testing. The result of this approach was the development of an engine cooling system that adequately controls air, oil and coolant temperatures during all driving and environmental conditions.

Squeak and rattle has become a primary source of undesired noise in automobiles due to the continual diminishment of engine, power train and tire noise levels. This article presents a finite-element-based methodology for the improvement of rattle performance of vehicle components. For implementation purposes, it has been applied to study the rattle of a glove compartment latch and corner rubber bumpers. Results from the glove compartment study are summarized herein. Extensions to other rattle problems are also highlighted.

This paper reports the analytical procedure developed for a simulation of knee impact during a barrier crash using a hybrid III dummy lower torso. A finite element model of the instrument panel was generated. The dummy was seated in mid-seat position and was imparted an initial velocity so that the knee velocity at impact corresponded to the secondary impact velocity during a barrier crash. The procedure provided a reasonably accurate simulation of the dummy kinematics. This simulation can be used for understanding the knee bolster energy management system. The methodology developed has been used to simulate impact on knee for an occupant belted or unbelted in a frontal crash. The influence of the vehicle interior on both the dummy kinematics and the impact locations was incorporated into the model. No assumptions have been made for the knee impact locations, eliminating the need to assume knee velocity vectors.

A flow network method was developed to predict the underhood temperature distribution of an automobile. The method involves the solution of simplified energy and momentum equations of the air flow in control volumes defined by subdividing the air space between the surfaces of the underhood components and the front-end geometry. The control volumes are interconnected by ducts with branches and bends to form a flow network. Conservation of mass and momentum with appropriate pressure-loss coefficients leads to a system of algebraic equations to be solved for the flow rates through each volume. The computed flow rates are transferred to a thermal model to calculate the temperatures of the air and the major vehicle components that affect the underhood environment. The method was applied to a 1986 3.0L Taurus and compared with vehicle experiments conducted in a windtunnel.

Although there was a safety awareness from the earliest days of the automobile, systematic approaches to designing for safety became more widespread after 1950 when large numbers of vehicles came into use in both the United States and Europe, and governments in both continents undertook a widespread highway development. Industry response to safety objectives and also to government regulation has produced a large number of safety enhancing engineering developments, including radial tires, disc brakes, anti-lock brakes, improved vehicle lighting systems, better highway sign support poles, padded instrument panels, better windshield retention systems, collapsible hood structures, accident sensitive fuel pump shut-off valves, and other items. A significant development was the design of the energy absorbing front structures.

Although the intent of the SHED test (Sealed Housing for Evaporative Determination) is to measure evaporative fuel losses, the SHED sampling methodology in fact measures hydrocarbons from all vehicle and test equipment sources. Leakage of air conditioning (AC) refrigerant is one possible non-fuel source contributing to the SHED hydrocarbon measurement. This report describes a quick and relatively simple method to identify the contribution of AC refrigerant to the SHED analyzer reading. R134A (CH2FCF3), the hydrofluorocarbon refrigerant used in all current automotive AC systems, as well as its predecessor, the chlorofluorocarbon R12, can be detected using the gas chromatography methods currently in place at many emissions labs for the speciation of exhaust and evaporative hydrocarbon emissions.

The importance of the automotive customer's perception of vehicle quality has been realized to be of utmost importance by car manufacturers. Sounds that occur within the passenger compartment can have a distinct affect on this “quality” impression. Many of these sounds originate from small DC motor driven systems within the vehicle. This study addresses the sound quality of motor driven power adjustable steering columns found in many luxury class vehicles. The primary components of this work include the subjective paired comparison evaluation of the sounds generated from these systems and the corresponding correlation to objective acoustic measures. The result is a set of perceptual regression models which showed the following: loudness level was the primary factor affecting sound quality perceptions for the telescoping, retraction, tilt up and tilt down sounds; sharpness was a secondary factor that influenced the sound quality perception of the tilt up and tilt down sounds.

The galvanostatic polarization method was used to determine the pitting potentials of candidate wrought aluminum alloys in inhibited ethylene glycol engine coolants. It was shown that the relative value of the pitting potential is an excellent measure of the long-term effectiveness of the coolants in preventing spontaneous pitting and crevice attack in the aluminum heat exchangers. The long-term effectiveness was determined by metallographic examination of aluminum heat exchangers subjected to a four-month, 50,000 mile simulated service circulation test.

In this study, we present an intelligent and wireless subsystem for powering and communicating with three sets of seat belt buckle sensors that are each installed on removable and interchangeable automobile seating. As automobile intelligence systems advance, a logical step is for the driver’s dashboard to display seat belt buckle indicators for rear seating in addition to the front seating. The problem encountered is that removable and interchangeable automobile seating outfitted with wired power and data links are inherently less reliable than rigidly fixed seating, as there is a risk of damage to the detachable power and data connectors throughout end-user seating removal/re-installation cycles.

The effects of engine operating conditions on the octane requirement and the resulting knock-limited output were studied on a single cylinder engine using production cylinder heads. A 4-valve cylinder head with port deactivation was used to study the effect of fuel octane, inlet air temperature, coolant temperature, air/fuel ratio, compression ratio and exhaust back pressure. The effect of the thermal environment was studied in more detail using separate cooling systems for the cylinder head and engine block on a 2-valve cylinder head. The results of this study compared closely with results found in the literature even though the engine and/or operating conditions were quite different in many cases.

The small-displacement direct-injection (DI) diesel engine is a prime candidate for future transportation needs because of its high thermal efficiency combined with near term production feasibility. Ford Motor Company and FEV Engine Technology, Inc. are working together with the US Department of Energy to develop a small displacement DI diesel engine that meets the key challenges of emissions, NVH, and power density. The targets for the engine are to meet ULEV emission standards while maintaining a best fuel consumption of 200g/kW-hr. The NVH performance goal is transparency with state-of-the-art, four-cylinder gasoline vehicles. Advanced features are required to meet the ambitious targets for this engine. Small-bore combustion systems enable the downsizing of the engine required for high fuel economy with the NVH advantages a four- cylinder has over a three-cylinder engine.

A structural ceramic diesel engine has the potential to provide low heat rejection and significant improvements in fuel economy. Analytical and experimental evaluations were conducted on the critical elements of this engine. The structural ceramic components, which included the cylinder, piston and pin, operated successfully in a single cylinder engine for over 100 hours. The potential for up to 8-11% improvement in indicated specific fuel consumption was projected when corrections for blow-by were applied. The ringless piston with gas squeeze film lubrication avoided the difficulty with liquid lubricants in the high temperature piston/cylinder area. The resulting reduction in friction was projected to provide an additional 15% improvement in brake specific fuel consumption for a multi-cylinder engine at light loads.

A method was adapted to measure the adhesion strength of polyurethane, semi-flexible foams to thermoplastic substrates. This method (lap-joint shear) was used to determine the effect of six (6) variables upon adhesion. These variables were: 1.) the type of substrate material, 2.) the type of polyurethane foam, 3.) the weight percentage of water in the polyurethane formulation (the degree to which the foam is blown and the chemical constituents), 4.) the chemical index of the polyurethane (the ratio of isocyanate to polyol resin), 5.) the surface roughness of the substrate, and 6.) the temperature of the polyurethane materials. Five (5) typical automotive interior thermoplastic substrates were studied: 1.) Polypropylene with preblended glass, 2.) Polycarbonate/ABS, 3.) PPO/HIPS with preblended glass, 4.) SMA with in-house dry blended glass, and 5.) SMA with preblended glass.

The intent of this paper is to summarize the work of the V8 power plant intake manifold radiated noise study. In a particular V8 engine application, customer satisfaction feedback provided observations of existing unpleasant noise at the driver's ear. A comprehensive analysis of customer data indicated that a range from 500 to 800 Hz suggests a potential improvement in noise reduction at the driver's ear. In this study the noise source was determined using various accelerometers located throughout the valley of the engine and intake manifold. The overall surface velocity of the engine valley was ranked with respect to the overall surface velocity of the intake manifold. An intensity mapping technique was also used to determine the major component noise contribution. In order to validate the experimental findings, a series of analysis was also conducted. The analysis model included not only the plastic intake manifold, but also the whole powertrain.

This paper describes a system modeling technique for predicting passenger compartment “boom” for a specific car design prior to the building of a prototype vehicle. Since “boom” — defined here as auditory response in the 20 Hz to 80 Hz frequency range — is dependent on body panel vibrations as well as air acoustic properties, three-dimensional finite element models of both body and air are constructed. These models are incorporated in existing vehicle models which include powertrain and chassis representations of the type previously used for performing shake and harshness analyses. To avoid non-symmetric mass and stiffness matrices, a modal method using auxilliary variables is utilized to couple the acoustic and body models. Included in the paper are discussions of modeling issues unique to structural acoustic simulation as well as several examples of studies in which sound pressure level response to realistic inputs is predicted and reduced by simulated design modifications.

Painting is the most difficult, the most costly, and the most polluting step in manufacturing vehicles. When low weathering performance paints are used, the results are dissatisfied customers, and huge warranty costs. It would obviously be wise to fully characterize the weathering performance of new coatings systems before they are used. Unfortunately this is not always practical. Coating formulations are changing rapidly in the States to comply with solvent emission regulations, the introduction of plastic substrates, and customer tastes. There is rarely enough time to wait ten years for outdoors exposure tests to reveal the "true" weathering performance of coatings before marketing vehicles. As a result, accelerated tests are often used to guide decisions. However, the results of such tests can be misleading because the harsh exposure conditions used can distort the chemistry of degradation.

Vehicle interior sound quality is regarded as a major quality attribute by automobile consumers and manufacturers. Whining noise, due to its steady state and tonal nature, is easily perceived as an annoyance to normal driving comfort. The blower motor in the climate control air-handling system can be a source of whining noise, especially when the motor is located in the passenger compartment. This paper describes a systematic case study carried out to identify the major noise generating mechanisms of a whining noise from the climate control air-handling system. The paper discusses the use of commonly available tools and techniques to resolve typical automotive NVH concerns resulting in improved sound quality. Particular measurement and analysis techniques presented include sound field mapping using acoustic intensity, resonance identification using transfer functions, three-axis spectrum analysis, and some physical modifications to the source and propagation paths.

Naturally aspirated Homogeneous Charge Compression Ignition (HCCI) operational window is very limited due to inherent issues with combustion harshness. Load range can be extended for HCCI operation using a combination of intake boosting and cooled EGR. Significant range extension, up to 8bar NMEP at 1000RPM, was shown to be possible using these approaches in a single cylinder engine running residual trapping HCCI with 91RON fuel with a 12:1 compression ratio. Experimental results over the feasible speed / load range are presented in this paper for a negative valve overlap HCCI engine. Fuel efficiency advantage of HCCI was found to be around 15% at 2.62bar / 1500RPM over a comparable SI engine operating at the same compression ratio, and the benefit was reduced to about 5% (best scenario) as the load increased to 5bar at the same speed.

When a window opens to provide the occupant with fresh air flow while driving, wind throb problems may develop along with it. This work focuses on an analytical approach to address the wind throb issue for passenger vehicles when a front window or sunroof is open. The first case of this paper pertains to the front window throb issue for the current Ford Escape. Early in a program stage, CAA (Computational Aeroacoustics) analysis predicted that the wind throb level exceeded the program wind throb target. When a prototype vehicle became available, the wind tunnel test confirmed the much earlier analytical result. In an attempt to resolve this issue, the efforts focused on a design proposal to implement a wind spoiler on the side mirror sail, with the spoiler dimension only 6 millimeters in height. This work showed that the full vehicle CAA analysis could capture the impact of this tiny geometry variation on the wind throb level inside the vehicle cabin.

This paper discusses a method to reduce the reliance on testing by using CAE to arrive at a stable instrument panel support structure which is capable of resisting the deployment of the passenger airbag. This technique has been used on various instrument panels, and has proven to be useful to the instrument panel design team. Tests have shown that deployment of the airbag results in large forces which act on an instrument panel. This paper describes a method to evaluate those forces and their impact on the surrounding instrument panel structure. The method uses loads from simple bench test data. Loads at the airbag mounting locations during an airbag deployment were measured. Those loads were used in the analysis to simulate the behavior of the airbag deployment on the instrument panel substrate. The analysis enabled the design engineering team to achieve an understanding of the event and to revise the surrounding instrument panel structure design in order to improve its performance.