Search Results

The New Car Assessment Program (NCAP), introduced in 1979 by the U.S. National Highway Traffic Safety Administration, is a vehicle safety rating system that conducts crash test and provides motoring consumers with an assessment of the safety performance of new cars. Similar programs were then developed around the world, initially for Europe (EuroNCAP), Australia (ANCAP), Japan (JNCAP), China (CNCAP) and Korea (KNCAP). NCAP most recently reached Latin America (LatinNCAP) and Southeast Asia (AseanNCAP). Although the roots are similar, many NCAP programs have significant differences on the test procedures and rating schemes. This paper is a comparative analysis of the recent NCAP protocols to highlight the most important technical differences.

With deflected-disc dampers, digressive force-velocity shapes are achieved via the combined effects of disc stack stiffness and hub-offset. The degree of digressiveness can be adjusted to alter vehicle performance by changing the proportion of these parameters. Optimizing this relationship can yield substantial vehicle performance improvements, but the time consuming iterative process of developing a new disc stack for each hub-offset discourages experimentation. To enable more efficient digressiveness comparisons, a regression-based computational method has been developed which converts disc stack stiffness from one hub-offset to other offsets directly, without iteration. Once an initial disc stack for one offset has been tuned by traditional methods, stacks for other offsets can be calculated that maintain overall damper control.

A simulation methodology is developed for the Constant Radius Constant Speed (CRCS) analysis to predict the ISO4138 [1] road test performance. The CRCS analysis can be used to predict the vehicle steady-state handling characteristics such as understeer, rear cornering compliance, and roll gradient, etc. The Yaw-Rate Control methodology is applied to replace the traditional driver-in-the-loop path-following approaches. Comparing to the path-following approaches, the proposed method is simpler to use, more efficient, accurate, and robust.

The preform annealing process is a two-stage stamping method for shaping non age-hardenable (i.e. 5000 series) aluminum sheet panels in which the panel is heat treated in between the two steps to improve overall formability of the material. The intermediate annealing heat treatment eliminates the cold work accumulated in the material during the first draw. The process enables the ability to form more complex parts than a conventional aluminum stamping process. A demonstration of local annealing for this process was conducted to form a one-piece aluminum liftgate inner panel for a large sport utility vehicle using the steel product geometry without design concessions. In prior work, this process was demonstrated by placing the entire panel in a convection oven for several minutes to completely anneal the cold work.

This paper outlines a process to assess the aerodynamic performance of different vehicle exterior surfaces. The initial section of the paper summarizes the details of white-light scanning process that maps entire vehicle to points in Cartesian co-ordinate system which is followed by the conversion of scanned points to theme surface. The concept of point-cloud modeling is employed to generate a smooth theme surface from scanned points. Theme surfaces thus developed are stitched to under-body/under-hood (UB/UH) parts of the base vehicle and the numerical simulations were carried out to understand the aerodynamic efficiency of the surfaces generated. Specifics of surface/volume mesh generated, boundary conditions imposed and numerical scheme employed are discussed in detail. Flow field over vehicle exterior is thoroughly analyzed. A comparison study highlighting the effect of front grilles in unblocked condition along with air-dam on flow field has been provided.

ASIL decomposition is a method described in the ISO 26262 standard for the assignment of ASILs to redundant requirements. Although ASIL decomposition appears to have similar intent to the hardware fault tolerance concept of IEC 61508-2, ASIL decomposition is not intended to reduce ASIL assignments to hardware elements for random hardware failures, but instead focuses on functions and requirements in the context of systematic failures. Based on our participation in the development of the standard, the method has been applied in different ways in practice, not all of which are fully consistent with the intent of the standard. Two potential reasons that may result in the use of “modified” ASIL algebra include the need of OEMs to partition a system and specify subsystem requirements to suppliers and the need for designers to construct systems bottom up.

Determining Li-ion battery life through life modeling is an excellent tool in determining and estimating end-of-life performance. Achieving End-of-Life (EOL) can be challenging since it is difficult to achieve both cycle and calendar life during the same test without years of testing. The plan to correlate testing with the model included three (3) distinct temperature ranges, beginning with the four-Season temperature profile, an aggressive profile with temperatures in the 50 to 55°C range, and using a mid-temperature range (40-45°C) as a final comparison test. A high duty-cycle drive profile was used to cycle all of the batteries as quickly as possible to reach the one potential definition of EOL; significant increases in resistance or capacity fade.

The main objective of this work is to demonstrate the merits of the Adjoint method to provide comprehensive information for shape sensitivities and design directions to achieve low drag vehicle shapes. The adjoint method is applied to a simple 2D airfoil and a 3D vehicle shape. The discrete Adjoint equations in the flow solvers are used to investigate further potential shape improvements of the low drag vehicle shapes. The low drag vehicle used in this study was designed earlier using the conventional approach (i.e., extensive use of wind tunnel testing). The goal is to use the already low drag vehicle shape and reduce its drag even further using the adjoint methodology without using the time-consuming and the high cost of wind tunnel testing. In addition, the present study is intended to compare the results with the other computational techniques such as surface pressure gradients method.

Understanding the flow characteristics and, especially, how the aerodynamic forces are influenced by the changes in the vehicle body shape, are very important in order to improve vehicle aerodynamics. One specific goal of aerodynamic shape optimization is to predict the local shape sensitivities for aerodynamic forces. The availability of a reliable and efficient sensitivity analysis method will help to reduce the number of design iterations and the aerodynamic development costs. Among various shape optimization methods, the Adjoint Method has received much attention as an efficient sensitivity analysis method for aerodynamic shape optimization because it allows the computation of sensitivity information for a large number of shape parameters simultaneously.

General Motors (GM), OnStar and the University of Michigan International Center for Automotive Medicine (ICAM) have formed a partnership to investigate and analyze real world rollover crashes involving GM vehicles equipped with rollover sensing technology and rollover-capable roof rail airbag systems. Candidates for the study are initially identified by OnStar, who receive notification of a rollover crash through the vehicle's Automatic Crash Response system. If the customer agrees to participate in the study, medical, vehicle and crash scene information are quickly gathered. This information is then reviewed by the medical and GM engineering communities to provide field relevant learning on injury mechanisms and vehicle system performance in rollover events. This paper provides a detailed review of the field case studies collected to date.

This paper presents some of the challenges and successful outcomes in developing the aerodynamic characteristics of the Chevrolet Volt, an electric vehicle with an extended-range capability. While the Volt's propulsion system doesn't directly affect its shape efficiency, it does make aerodynamics much more important than in traditional vehicles. Aerodynamic performance is the second largest contributor to electric range, behind vehicle mass. Therefore, it was critical to reduce aerodynamic drag as much as possible while maintaining the key styling cues from the original concept car. This presented a number of challenges during the development, such as evaluating drag due to underbody features, balancing aerodynamics with wind noise and cooling flow, and interfacing with other engineering requirements. These issues were resolved by spending hundreds of hours in the wind tunnel and running numerous Computational Fluid Dynamics (CFD) analyses.

An air suspension system can consist of many different components. These components include an air compressor, air springs, pneumatic solenoid valves, height sensors, electronic control unit, air reservoir, air lines, pressure sensor, temperature sensor, etc. The system could be designed as a 2-corner rear air suspension or a 4-corner air suspension. In this paper, the pneumatic models of air suspension systems are presented. The suspension system models are implemented in AmeSim. The suspension controls are implemented using Matlab/Simulink. The compressor was modeled using the standard AmeSim element with known mass flow rate as a function of pressure ratio. Air lines were modeled using a friction submodel of pneumatic pipe and control (isolation) valves are modeled using 2 position, 2 port pneumatic servo valves. The air spring is modeled as a single pneumatic chamber, single rod jack with spring assistance to account for spring nonlinearities.

Presented in the paper is a comprehensive analysis for floating piston pin. It is more challenging because it is a special type of journal bearing where the rotation of the journal is coupled with the friction between the journal and the bearing. In this analysis, the multi-degree freedom mass-conserving mixed-EHD equations are solved to determine the coupled pin rotation and friction. Other bearing characteristics, such as minimum film thickness, pin secondary motions in both connecting-rod small-end bearing and piston pin-boss bearing, power loss etc are also determined. The mechanism for floating pin to have better scuffing resistance is discovered. The theoretical and numerical model is implemented in the GM internal software FLARE (Friction and Lubrication Analysis for Reciprocating Engines).

An extruded Mg-Al-Mn (AM30) magnesium alloy was subjected to uniaxial compression along the extrusion direction (ED) and the extrusion radial direction (RaD) at 450 °C and different strain rates. The microstructure and texture of the AM30 alloy under different deformation conditions were examined. Texture evolution was characterized by electron backscatter diffraction (EBSD). The activity of different deformation modes including twinning were simulated using the visco-plastic self-consistent (VPSC) and the simplistic Sachs polycrystal plasticity models. The results show that the microstructure and the mechanical property of the Mg alloy strongly depend on the strain rate, with twinning activated at strain rates >0.5 s−1. Dynamic recrystallization and twinning interacted with each other and affected the final microstructure and mechanical property of the magnesium alloy.

The sustainable use of energy and the reduction of pollutant emissions are main concerns of the automotive industry. In this context, Hybrid Electric Vehicles (HEVs) offer significant improvements in the efficiency of the propulsion system and allow advanced strategies to reduce pollutant and noise emissions. The paper presents the results of a simulation study that addresses the minimization of fuel consumption, NOx emissions and combustion noise of a medium-size passenger car. Such a vehicle has a parallel-hybrid diesel powertrain with a high-voltage belt alternator starter. The simulation reproduces real-driver behavior through a dynamic modeling approach and actuates an automatic power split between the Internal Combustion Engine (ICE) and the Electric Machine (EM). Typical characteristics of parallel hybrid technologies, such as Stop&Start, regenerative braking and electric power assistance, are implemented via an operating strategy that is based on the reduction of total losses.

Today, nearly half of the world population lives in urban areas. As the world population continues to migrate to urban areas for increased economic opportunities, addressing personal mobility challenges such as air pollution, Greenhouse Gases (GHGs) and traffic congestion in these regions will become even a greater challenge especially in rapidly growing nations. Road transportation is a major source of air pollution in urban areas causing numerous health concerns. Improvements in automobile technology over the past several decades have resulted in reducing conventional vehicle tailpipe emissions to exceptionally low levels. This transformation has been attained mainly through advancements in engine and transmission technologies and through partial electrification of vehicles. However, the technological advancements made so far alone will not be able to mitigate the issues due to increasing GHGs and air pollution in urban areas.

Insulation coordination requirements for electrical equipment applications are defined in various standards. The standards are defined for application to stationary mains connected equipment, like IT, power supply or industrial equipment. Protection from an electric shock is considered the primary hazard in these standards. These standards have also been used in the design of various automotive components. IEC 60664-1 is an example of the standard. Automobiles are used across the world, in various environments and in varied usage by the customers. Automobiles need to consider possible additional hazards including electric shock. This paper will provide an overview of how to adapt these standards for automotive application in the design of High Voltage (HV) automotive components, including High Voltage batteries and other HV components connected to the battery. The basic definitions from the standards and the principles are applied for usage in automotive applications.

The GD₃ or GD Cubed method of problem prevention has been applied to product changes and to test results at the component, subsystem and vehicle level. GD₃ stands for Good Design - Good Discussion - Good Dissection. Good Discussion of changes (Design Review Based on Failure Mode) identifies BUDS of PROBLEMS that may arise from interfaces and areas of change. Good Dissection (Design Review Based on Test Results) is applied to physical test samples during and after tests to identify Buds of Problems that may not be obvious from inspection of the parts or test results. The paper first describes implementation of the GD₃ principles and methods supporting Good Discussion (DRBFM) and Good Dissection, and then discusses how they are applied and embedded in the Vehicle Development Process at General Motors Co.

This paper examines Smart Electric Power Management as it pertains to when the vehicle charging system is active. Over the past decade there have been several factors at play which have stressed the demands placed upon the vehicle electrical power system. Many of these factors present challenges to electrical power that are at cross-purposes with one another. For example, demands of new and existing electrical loads, customer expectations about load performance and battery life, and the push by governments' world-wide for increased fuel economy (FE) and reduced CO2 emissions all have direct impact and can be directly impacted by decisions made in electric power design. As the electrification of the vehicle has progressed we now have much more specific vehicle state data available and the means to share this information among on-board computers through serial data link connectivity.

For many years, the computer aided math model has been the foundation for lowering cost and reducing time to market for many manufacturing industries. The automotive industry applies a variety of tools and methods to evaluate the expected vehicle performance to a forever expanding set of requirements. These mathematical predictions of performance are then repeated for both a set of design cycles and a multitude of vehicles in the product portfolio. This paper presents a CAE perspective of the unique problems of the large scale virtual vehicle engineering factory and a set of solutions. Different strategies to create the various complex math models required are explored. These strategies include using COTS FEA pre-processers, producing FEA models internal to the CAD tools, as well as custom built tools, macros and process automation tools.