Search Results

Fundamental differences exist between sheet metal forming and hydroforming processes. Sheet metal forming is basically a one step metal fabrication process. Almost all plastic deformation of an originally flat blank is introduced when the punch is moved normal to a clamped sheet metal. Hydroforming, however, consists of multiple steps of tube making, pre-bending, crushing, pressurization, etc. Each of the above mentioned steps can introduce permanent plastic deformations. The forming limit diagram obtained for sheet metal forming may or may not be used in hydroforming evaluations. A failure criterion is proposed for predicting bursting failures in tube hydroforming. The tube material's stress-strain curve, obtainable from uniaxial tensile test and subjected to some postulations under large stress/strain states, is used in judging the failure.

The overall vision of this project was to develop a new technology that will be an enabler to reduce design and development time of HVAC systems by an order of magnitude. The objective initially was to develop a parametric model of an automotive HVAC Windshield Defrost Duct coupled to a passenger compartment. It can be used early on in the design cycle for conducting coarse packaging studies by quickly exploring “what-if” design alternatives. In addition to the packaging studies, performance of these design scenarios can be quickly studied by undertaking CFD simulation and analyzing flow distribution and windshield melting patterns. The validated geometry and CFD models can also be used as knowledge building tools to create knowledge data warehouses or repositories for precious lessons learned.

USING a high-speed motion picture camera, flame photographs were taken of the combustion process associated with the starting of hot gasoline engines. Compression ignition at isolated points followed by normal combustion caused peak cylinder pressures to occur prior to top dead-center under some low-speed engine conditions. In addition, an abnormal combustion phenomenon was observed in the last part of the charge to burn. The reaction rate was appreciably faster than normal for the engine speed and much slower than is usually observed in knocking combustion at normal engine speeds.

THIS description of the hydraulic control used with the hydra-matic transmission reveals how the control operates to change ratios under power without direction from the driver. The control's pattern of automatic shifting for ordinary, high-range driving has been selected as the best compromise between top performance and low ratio of engine noise to wind noise. The control's low range shifts gears according to performance dictates alone, furnishing greater power for extreme conditions at low speeds and enabling the driver to use his engine as a brake on steep descents. Heart of the control system is a double hydraulic governor, sensitive both to car speed and throttle opening. THIS paper, as well as the two that follow, one by Messrs. Nutt and Smirl and the other by Mr. Kimberly, make up a symposium on automatic transmission components presented at the 1947 SAE Summer Meeting.

Variable valve actuation has become a very popular feature in today's engines. With many of these systems being hydraulically actuated, the engine lubrication system requires enhancement to support their function. To expand the system's operational range with respect to speed and temperature, a traditional solution has been to increase oil pressure by increasing pump displacement. To better optimize the system, a variable displacement vane pump has been adapted to the engine lube oil system. Based on existing transmission pump technology, a pivoting cam ring design is employed that is able to vary the pump's displacement as a function of pump regulating oil pressure which in-turn provides a net reduction in its drive torque. While others have addressed this issue using complex and expensive pressure regulating systems, this passive solution requires no valves or additional hardware.

A numerical simulation of the flow structure around an idealized automotive A-pillar rain-gutter and the sound radiated from it is reported. The idealized rain-gutter is an infinitesimally thin backward facing elbow mounted on a flat plate. It is kept in a virtual wind-tunnel with rectangular cross-section. The transient flow structure around the rain-gutter is described and time-averaged pressure distribution along the base plate is provided. Time-varying static pressure was recorded on every grid point on the base-plate as well as the rain-gutter surfaces and used to calculate sound pressure signal at a microphone held above the rain-gutter using the Ffowcs-Williams-Hawkings (FWH) integral method was used for calculating sound propagation. Both the transient flow simulation as well as the FWH sound calculation were performed using the commercial CFD code FLUENT6.1.22.

This paper describes the recent efforts on developing an automotive climate control system throughout integrating an electrically-controlled variable capacity scroll compressor with a fuzzy logic control-based refrigerant flow management. Applying electrically-controlled variable capacity compressor technology to climate control systems has a significant impact on improving vehicle fuel economy, achieving higher passenger comfort level, and extending air and refrigerant temperature controllability as well. In this regard, it is very important for automotive climate control engineers to layout a system-level temperature control strategy so that the operation of variable capacity compressor can be optimized through integrating the component control schemes into the system-level temperature control. Electronically controlled expansion devices have become widely available in automotive air conditioning (A/C) systems for the future vehicle applications(1, 2, 3 and 4).

During the automotive brake system design and development process, a large number of performance characteristics must be comprehended, assessed, and balanced against each other and, at times, competing performance objectives for the vehicle under development. One area in brake development that is critical to customer acceptance due to its impact on a vehicle's perceived quality is brake pedal feel. While a number of papers have focused on the specification, quantification and modeling of brake pedal feel and the various subsystem characteristics that affect it, few papers have focused specifically on brake corner hoses and their effect on pedal feel, in particular, during race-track conditions. Specifically, the effects of brake hose fluid consumption pedal travel and brake system response is not well comprehended during the brake development process.

TURBOGLIDE is the deluxe automatic transmission of the General Motors Chevrolet. One of its most important features is that its performance ratio is available at any throttle position, enabling control of torque ratio and engine output by the throttle pedal. The system includes a five-element torque converter, pump, three turbines, and the dual stator. The entire installed unit weighs 148 lb, a result of the general arrangement and the use of aluminum in the case and bell housing. The authors discuss the basic operating principle of the transmission, the arrangement, performance, torque distribution, control system, and valve body.

A spectroscopic diagnostic system was designed to study the effects of different engine parameters on the chemiluminescence characteristic of HCCI combustion. The engine parameters studied in this work were intake temperature, fuel delivery method, fueling rate (load), air-fuel ratio, and the effect of partial fuel reforming due to intake charge preheating. At each data point, a set of time-resolved spectra were obtained along with the cylinder pressure and exhaust emissions data. It was determined that different engine parameters affect the ignition timing of HCCI combustion without altering the reaction pathways of the fuel after the combustion has started. The chemiluminescence spectra of HCCI combustion appear as several distinct peaks corresponding to emission from CHO, HCHO, CH, and OH superimposed on top of a CO-O continuum. A strong correlation was found between the chemiluminescence light intensity and the rate of heat release.

Air flow around the front brake assembly was computed using STAR-CD version 2.300, a commercial Computational Fluid Dynamics (CFD) code in order to explore the possibility of using this technique as a design tool. The primary objective in a brake corner assembly design is to maximize air cooling of the brake rotor. It is a very challenging task that requires experiments that are both expensive and time consuming in order to evaluate and optimize the various design possibilities. In this study, it is demonstrated that the design procedure can be shortened and made less expensive and be accurate using flow simulations. Accordingly, the air flow around the front brake assembly was computed for three different designs and for three different car speeds. A computational mesh was built using PROSTAR, the STAR-CD pre and post-processor. The three-dimensional mesh had almost 900,000 cells. All geometrical components were modelled.

Casting technology developmentshave led to a manufacturing process that allows the casting of thin wall (2-3mm) heat resistant ferritic stainless steel exhaust manifolds which can replace stamped and tubular weldments as well as iron castings where temperature requirements are increased. This casting process combines the thin wall and clean metal benefits of the counter gravity, vacuum-assist casting process using thin, light-weight bonded sand molds supported by vacuum-ridgidized sand. This combination is called the LSVAC (Loose Sand Vacuum Assisted Casting) process, a patented process. This process will significantly contribute to the growth of near-net shape steellstainless steel castings for automotive and allied industries. For exhaust manifolds, a modified grade of ferritic stainless steel with good oxidation resistance to 950°C in high dew point synthetic exhaust gas atmospheres was developed.

Brake caliper and corner behavior in the off-brake condition can lead, at times, to brake system performance issues such as residual drag (and related issues such as pulsation, judder, and loss of fuel economy), and caliper pryback during aggressive driving maneuvers. The dynamics in the brake corner can be strikingly complex, with numerous friction interfaces, rubber component and grease dynamics, deflections of multiple components, and significant dependence on usage conditions. Displacements of moving parts are usually small, and the residual forces in the caliper interfaces involved are also small in comparison with other forces acting on the same components, making direct observation very difficult. The present work attempts to illuminate off-brake behavior in two different conditions - residual drag and pryback - through the use of low-range pressure distribution sensors placed in between the caliper (pistons and fingers) and the brake pad pressure plates.

Component operating temperatures affect both the reliability and performance of automotive alternators. It is desirable to keep the rectifier bridge and regulator temperatures below 175 C because of the semiconductors contained in this area. At temperatures greater than this, expected lifespans have been observed to decay exponentially [1]. The air flow field surrounding an alternator and component temperature fields were investigated with Computational Fluid Dynamics (CFD) simulations. The objectives of the simulations were to examine the velocity field for the flow passage and the temperature fields for the components. Design proposals have been made to improve the air flow and to reduce the operating temperature. An initial investigation was performed by setting an alternator in a test configuration and applying the appropriate heat generation for each component. The high temperatures in the alternator components occurred in the stator and the rectifier.

Casting, machining and structural simulations were completed on a V8 engine block made in Compacted Graphite Iron (CGI) for use in a racing application. The casting and machining simulations generated maps of predicted tensile strength and residual stress in the block. These strength and stress maps were exported to a finite element structural model of the machined part. Assembly and operating loads were applied, and stresses due to these loads were determined. High cycle fatigue analysis was completed, and three sets of safety factors were calculated using the following conditions: uniform properties and no residual stress, predicted properties and no residual stress, and predicted properties plus residual stress.

A transient, one-dimensional, two-phase (crankcase gases and liquids) flow network model was developed (and coded in FORTRAN) to calculate the crankcase pressures versus crank angle during engine operation and the consequent crankcase pumping mean effective pressure (CPMEP). The two-phase flow was represented by an empirical expression. Note, CPMEP is one of the components of engine FMEP (friction mean effective pressure) and is being introduced here as a new term. The model was calibrated with engine crankcase pressure measurements. The motivation for the present work was the fact that no commercial (or public domain) software is available to adequately address this subject in sufficient detail. The model also predicts that closing (i.e. sealing) the individual bays of an engine can result in (nearly) zero CPMEP. This was confirmed by motored single cylinder engine measurements.

A typical problem in integral body vehicles is the isolation of high frequency vibration and noise. A method of attacking this problem is presented for isolation of engine noise. A mount concept which acts as a mechanical low pass filter was analyzed, designed and tested. Results in reducing engine noise in the vehicle show it to be an effective method.

The air passages in tailpipe end geometries are investigated with Computational Fluid Dynamics (CFD) simulations. The overall objective of the simulations is to select an optimum design which has a mimimum capacity for noise generation. This is accomplished by comparing pressure drops between inlet and outlet and by examining the turbulent kinetic energy levels in the flow domain. Two designs for the tailpipe end geometries were evaluated. It was found that turbulent kinetic energy levels and pressure drops were lowest in a single pipe design which had relatively smooth internal contours. We conclude that the present CFD approach can provide useful design information in a short time frame (a few weeks) for exhaust pipe tip geometries for reduced pressure drop and noise generation.

FIGURE 1 The 200 HP high performance 4.3L Vortec V6 engine has been developed to satisfy the need for a fuel efficient performance powerplant in the General Motors small truck platforms. Marketing requirements included strong low and mid range torque, relatively high specific power, smoothness and noise comparable to the best competitive six cylinder engines, excellent driveability, and a new technology image. Maintaining the 4.3L engine record of high reliability and customer satisfaction was an absolute requirement. Fuel economy and exhaust emission performance had to meet expected customer and legislated requirements in the mid 1990's.