Search Results

In this paper, a hybrid roll control system, including passive and active roll control units, is designed to improve the roll dynamics of tanker vehicles and to reduce the lateral shifts of the liquid cargo due to lateral accelerations. The passive control system consists of radial partitions installed inside the vehicle container. These partitions rotate in phase with the liquid cargo as one unit about the longitudinal axis of the container in response to the induced momentum forces due to the lateral acceleration excitation. Torsion dampers are fixed between the partitions and the container's front and rear walls to reduce the oscillating motion of the liquid cargo. While the passive partition dampers control the dynamics of the liquid cargo inside the container, the dampers of the vehicle suspension are switchable, generating anti-roll damping moments based on the lateral acceleration level and the container filling ratio.

Vehicle Handling performance depends on many parameters. One of the most important parameters is the dynamic behavior of the steering system. However, steering system had been enhanced thoroughly over the past decade where Active Front Steering (AFS) is now present and other system as Active Independent Front Steering (AIFS) is currently in the research phase. Actually, AFS system adopt the front wheels’ angles base on the actual input steering angle from the driver according to vehicle handling dynamics performance. While, the AIFS controls the angle of each front wheel individually to avoid reaching the saturation limits of any of the front wheels’ adhesion. In this paper modeling and analysis of an AIFS is presented with Tire Work Load (TWL) based controller. Magic Formula tire model is implemented to represent the tire in lateral slip condition.

The latest developments in the engine’s design aim to maximize the power output, downsize the engine, and minimize the fuel consumption. This paper investigates the thermomechanical loads on the piston of a turbocharged diesel engine. The main emphasis is the effect of increasing the boosting pressure on the piston loading until the possible maximum engine power is achieved. Also, it proposes the modification of the piston design in order to increase the durability for more power loading and decrease the total mass. The temperature distribution on the piston body, the corresponding thermomechanical deformations, the stress distribution, and the safety factor is excessively calculated. Finite element methods (ANSYS workbench) is used to analyze the thermomechanical loads applied to a three-dimensional model. The study is applied to the piston of a 300 hp diesel engine (base case) in order to increase the engine power by 17% (upgraded one).

This study presents a practical theoretical method to judge the aerodynamic response of buses in the early design stage based on both aerodynamic and design parameters. A constant longitudinal velocity 2-DOF vehicle lateral dynamics model is used to investigate the lateral response of a bus under nine different wind gusts excitations. An appropriate 3-D CFD simulation model of the bus shape results is integrated with carefully chosen design parameters data of a real bus chassis and body to obtain vehicle lateral dynamic response to the prescribed excitations. Vehicle model validity is carried out then, the 2-DOF vehicle lateral dynamics model has been executed in MATLAB Simulink environment with the selected data. Simulation represents the vehicle in a straight ahead path then entered a gusting wind section of the track with a fixed steering wheel. Vehicle response includes lateral deviation (LD), lateral acceleration (LA), yaw angle (YA) and yaw rate (YR).

A non-linear mathematical model of a semi-active (2DOF) vehicle suspension using a magnetorheological (MR) damper with information concerning the road profile ahead of the vehicle is proposed in this paper. The semi-active vibration control system using an MR damper consists of two nested controllers: a system controller and a damper controller. The fuzzy logic technique is used to design the system controller based on both the dynamic responses of the suspension and the Padé approximation algorithm method of a preview control to evaluate the desired damping force. In addition, look-ahead preview of the excitations resulting from road irregularities is used to quickly mitigate the effect of the control system time delay on the damper response.

Dynamic modeling of the gear vibration is a useful tool to study the vibration response of a geared system under various gear parameters and operating conditions. An improved understanding of vibration signal is required for early detection of incipient gear failure to achieve high reliability. However, the aim of this work is to make use of a 6-degree-of-freedom gear dynamic model including localized tooth defect for early detection of gear failure. The model consists of a gear pair, two shafts, two inertias representing load and prime mover and bearings. The model incorporates the effects of time-varying mesh stiffness and damping, backlash, excitation due to gear errors and modifications. The results indicate that the simulated signal shows that as the defect size increases the amplitude of the acceleration signal increases. The crest factor and kurtosis values of the simulated signal increase as the fault increases.

In order to achieve the high capability of the ride comfort and regulating the tire slip ratio, a preview of a nonlinear semi-active vibration control suspension system using a magnetorheological (MR) fluid damper is integrated with traction control in this paper. A controlled semi-active suspension system, which consists of the system controller and damper controller, was used to develop ride comfort, while the traction controller is utilized to reduce a generated slip between the vehicle speed and rotational rate of the tire. Both Fractional-Order Filtered Proportional-Integral-Derivative (P¯IλDμ) and Fuzzy Logic connected either series or parallel with P¯IλDμ are designed as various methodologies of a system controller to generate optimal tracking of the desired damping force. The signum function method is modified as a damper controller to calculate an applied input voltage to the MR damper coil based on both preview signals and the desired damping force tracking.

Vehicle suspension is considered a vital system of modern automotive and necessary to offer an adequate level of ride comfort and roadholding. In the present paper, a fuzzy-based sliding surface (FBSS) controller is designed, as a system controller for the first time, for a semi-active vehicle suspension using a magnetorheological (MR) damper in order to minimize the transmitted unwanted vibrations to the passengers. Therefore, an ideal reference skyhook model is employed to construct the sliding surface, which is the input of fuzzy logic. MR damper is a semi-active device and is controlled indirectly using an external voltage source. So a neural-based damper controller is used to compute the applied voltage to the magnet coil of the MR damper in series with the FBSS system controller. The proposed semi-active controlled quarter-vehicle suspension using an MR damper is solved numerically by Matlab.

E-spring is a recent innovation in vehicle suspension springs. Its behavior and characteristics are investigated experimentally and verified numerically. The mechanical and frequency-response-based properties of E-springs are investigated experimentally at both of the structural and constitutional levels. Thermoplastic-based and thermoset-based fibrous composite structures of the E-springs are modified at micro-scale with various additives and consequently they are compared. The experimental results reveal that additives of micrometer-sized particles of mineral clay to an ISO-phthalic polyester resin of the composite E-spring can demonstrate distinguished characteristics. A hybrid approach of the inter-laminar shear stress and Tsai-Wu criteria is implemented in order to identify failure indices numerically at the utmost level of loading and verify the experimental results.

A hybrid search optimization is presented in order to optimize hybrid laminated fibrous composite E-springs for vehicle suspension systems. This optimization is conducted with both of the geometrical configuration and laminate structure of the E-spring. A genetic algorithm along with a hill-climbing random-walk approach are used through a developed NURBS-based technique in order to conduct this optimization. A mathematical-modeling-based mid-ware technology is introduced in order to fully automate the optimization process through linking the run engines of mathematical modeling and finite element analysis from within the mathematical modeling engine. A hybrid approach of the inter-laminar shear stress and Tsai-Wu criteria is first implemented in order to identify failure indices of the resulting optimum shape and laminate structure.

Adaptive neuro-fuzzy inference system (ANFIS) technique has been developed and applied by numerous researchers as a very useful predictor for nonlinear systems. In this paper, non-parametric models have been investigated to predict the direct and inverse nonlinear dynamic behavior of magnetorheological (MR) fluid dampers using ANFIS technique to demonstrate more accurate and efficient models. The direct ANFIS model can be used to predict the damping force of the MR fluid damper and the inverse dynamic ANFIS model can be used to offer a suitable command voltage applied to the damper coil. The architectures and the learning details of the direct and inverse ANFIS models for MR fluid dampers are introduced and simulation results are discussed. The suggested ANFIS models are used to predict the damping force of the MR fluid damper accurately and precisely. Moreover, validation results for the ANFIS models are proposed and used to evaluate their performance.

In this paper, semi-active MR main suspension system based on system controller design to minimize pitch motion linked with MR-controlled seat suspension by considering driver’s biodynamics is investigated. According to a fixed footprint tire model, the transmitted tire force is determined. The linear-quadratic Gaussian (LQG) system controller is able to enhance ride comfort by adjusting damping forces based on an evaluation of body vibration from the dynamic responses. The controlled damping forces are tracked by the signum function controllers to evaluate the supply voltages for the front and rear MR dampers. Based on the sprung mass acceleration level and its derivative as the inputs, the optimal type-2 (T-2) fuzzy seat system controller is designed to regulate the controlled seat MR damper force.

A non-contact analysis of a drum brake based on three-dimensional Finite Element analysis using Ansys is presented. The effect of drum-lining interface stiffness and line pressure on the interface contact is examined. The modal analysis of the vehicle drum brake is also studied to get the natural frequency and instability of the drum. It is shown that the unsymmetric modal analysis is efficient enough to solve this linear problem after transforming the non-linear behaviour of the contact between the drum and the lining to a linear behavior. A linear element which is used in the modal analysis is transferred to non-linear elements which are Targe170 and Conta173 that represent the drum and lining to study the contact analysis. The contact analysis problems are highly non-linear and require significant computer resources to solve it, however, the contact problem give two significant difficulties.

It is well known that the excessive levels of vibration in heavy vehicles negatively affect driver comfortability, cargo safety and road condition. The current challenge in the field of suspension design for heavy vehicles is to optimize the suspension dynamic parameters to improve such requirements. Almost all of the previous work in this field is based on applying the mathematical optimization considering active or passive suspension systems to obtain the optimal dynamic parameters. In this work a new passive suspension systems for heavy trucks is suggested and compared with the conventional passive suspension systems. The new systems rely on transferring the vertical motion, (vibration), into horizontal motion through a bell-crank mechanism to be taken by a horizontal passive suspension system. The system dynamic parameters like body acceleration, suspension travel and dynamic tire load are calculated assuming random excitation due to road irregularities.

Integral Control strategy for vehicle chassis systems had been of great interest for vehicle designers in the last decade. This paper represents the interaction of longitudinal control and lateral control. In other words the traction control system and handling control system. Definitely, tire properties are playing a vital role in such interaction as it is responsible for the generated forces in both directions. A seven degrees of freedom half vehicle model is derived and used to investigate this interaction. The vehicle body is represented as a rigid body with three degrees of freedom, lateral and longitudinal, and yaw motions. The other four degrees are the two rotation motion of the front wheel and the rear wheel. This two motions for each wheel are spin motion and the steering motion. The traction controller is designed to modulate engine torque through adjusting the throttle angle of the engine upon utilized adhesion condition at the driving road wheels.

Many basic studies were conducted to discover the main reason for squeal occurrence in both disc and drum brake systems. As, it is well-known that the squealed brake system is more effective than the non-squealed brake system and it is also a common discomfort. So, cancellation of the squeal is not preferable, however, elimination of the brake squeal is a favorable. An approach to study the drum brake squeal is presented based mainly on the Finite Element Method (FEM) representation. The brake system model is based also on the model information extracted from finite element models for individual brake components. This finite element method (FEM) was used to predict the mode shape and natural frequency of the brake system after appropriate verification of FEM.

Vehicle suspension along with tires and steering linkages is designed for safe vehicle control and to be free of irritating vibrations. Therefore the suspension system designs are a compromise between ride softness and handing ability. However, this work is concerned with a theoretical investigation into the ride behavior of actively suspended vehicles. It is based on using fuzzy logic control (FLC) to implement a new sort of active suspension system. Comparisons between the behavior of active suspension system with FLC with those obtained from active systems with linear control theory (LQR), ideal skyhook system and the conventional passive suspension systems. Results are introduced in such a way to predict the benefits that could be achieved from fuzzy logic system over other competing systems. Furthermore, a controller is designed and made by using results of FLC system, theoretical inputs are used to examine the validity of this controller.

The number of speed humps (sleeping policemen) has seen a global increase in the last decade. This paper addresses the geometric requirements of these humps using Genetic Algorithms optimization techniques to control the speed, stability, and ride feel of the traversing vehicles. The interaction between road hump profile and the modeled vehicles (passenger and a two-axle truck) are studied with a dynamic model. The shape of the proposed profile is described by numbers of amplitudes of harmonic functions. The extreme acceleration of the drivers’ seats of the vehicles traversing the hump is set as multiobjective function for the optimization process, taking into consideration the road-holding ability represented by the tire lift-off speed. The results show that hump geometry can be improved while fulfilling the requirements of speed control and vehicle dynamic responses.

Extensive studies of off-road non-pneumatic tires (NPTs) were conducted for light and heavy equipment due to their advantages over conventional pneumatic tires in terms of low rolling resistance, thus no need for air pressure maintenance. Finite element (FE) simulations of NPT contact pressure, contact shear stress, vertical stiffness, von mises stress, and rolling resistance were performed using ABAQUS software in a series of vertical loads to simulate tire models of three different spokes geometries on unpaved soil to verify NPT performance under different conditions. The spokes geometries were hexagonal (honeycomb) spoke, hexagonal re-entrant (Lattice) spoke and spoke with curvature called spoke pairs. It was found that the rolling resistance of the honeycomb structure has the lowest value, while the contact shear stress and contact pressure were the highest.

During the last few decades, fibrous composite materials have been diversified and replaced some traditional metallic materials. These materials provide high strength to weight ratio together with high environmental corrosion resistance. One of the basic engineering applications, which have been attracted by the properties of these composites, is the automotive engineering. In this paper, the authors manipulated the composite C-compression springs as a new trend of vehicle suspension system instead of coil or leaf springs. This type of springs can be safely and efficiently implemented in the vehicles' suspension systems and most probably be used in the new suspension design proposed earlier by one of the authors. Previous work on this context had shown a quality nature and economical technology in the use of composite springs in transportation and/or industrial applications.