Search Results

In recent years, improvements in the fuel economy and exhaust emission performance of internal combustion engines have been increasingly required by regulatory agencies. One of the salient concerns regarding general purpose engines is the larger amount of CO emissions with which they are associated, compared with CO emissions from automobile engines. To reduce CO and other exhaust emissions while maintaining high fuel efficiency, the optimization of total engine system, including various design parameters, is essential. In the engine system optimization process, cycle simulation using 0-D and 1-D engine models are highly useful. To define an optimum design, the model used for the cycle simulation must be capable of predicting the effects of various parameters on the engine performance. In this study, a model for predicting the performance of a general purpose SI (Spark Ignited) engine is developed based on the commercially available engine simulation software, GT-POWER.

Crankshafts of motorcycles require high strength, high reliability and low manufacturing cost. Recently, a reduction of Pb content in the free-cutting steel, which is harmful substance, is required. In order to satisfy such requirements, we started the development of Pb-free free-cutting steel which simultaneously enabled the omission of the normalizing process. For the omission of normalizing process, we adjusted the content of Carbon, Manganese and Nitrogen of the steel. This developed steel can obtain adequate hardness and fine microstructure by air-cooling after forging. Pb-free free-cutting steel was developed based on Calcium-sulfur free-cutting steel. Pb free-cutting steel is excellent in cutting chips frangibility in lathe process. We thought that it was necessary that cutting chips frangibility of developed steel was equal to Pb free-cutting steel. It was found that cutting chips frangibility depend on a non-metallic inclusion's composition, shape and dispersion.

A dual piston Variable Compression Ratio (VCR) engine has been newly developed. This compact VCR system uses the inertia force and hydraulic pressure accompanying the reciprocating motion of the piston to raise and lower the outer piston and switches the compression ratio in two stages. For the torque characteristic enhancement and the knocking prevention when the compression ratio is being switched, it is necessary to carry out engine controls based on accurate compression ratio judgment. In order to accurately judge compression ratio switching timing, a control system employing the Hidden Markov Model (HMM) was used to analyze vibration generated during the compression ratio switching. Also, in order to realize smooth torque characteristics, an ignition timing control system that separately controls each cylinder and simultaneously performs knocking control was constructed.

A hybrid simulation model in the transient bench was developed to realize the characteristics of the transient behavior and the fuel economy equivalent to that of a real vehicle. The motors and the batteries that were main components of the hybrid vehicle system were simulated as constructive modules, the functions of which have the integrated control and the input/output (I/O) function with real components. This model enabled us to accommodate a variety of auxiliary (AUX) I/O flexibly. The accuracy of the model was verified by the transient characteristics of the engine and the fuel economy result through correlation with a mass-produced vehicle. Furthermore, the flexibility of the model to a variety of AUX I/O was examined from the simulation test of the vehicle equipped with the waste heat recovery (WHR) system.

In recent years, electrification of powertrains has been promoted to improve fuel efficiency and CO2 emissions. Along with electrification, it is possible to reduce engine usage frequency and improve the fuel efficiency in traveling. Especially in a hybrid electric vehicle (HEV), the state changes from motor assist mode to engine firing mode. As a result, stay time in eigenvalue of a powertrain is shortened, and vibration of the vehicle body at the engine start situation is able to be reduced as compared with conventional engine-driven vehicle. However, since the HEV is equipped with a high compression ratio engine for improving fuel economy, there is cause for concern that excitation force generated by the powertrain at the time of engine start increases. Also, the vehicle body vibration at engine start situations requires further consideration, because the operation frequency of engine decreases.

Traditionally, the suitability of wireless terminals for automotive use has been evaluated by conducting repeated driving tests in actual environments. However, this method of evaluation has long presented issues, and the implementation of the method itself is today becoming increasingly challenging. A method of evaluating the suitability of terminals for onboard use by generating virtual radio wave environments on a PC has therefore been developed by applying a two-stage method to multiple-input multiple-output (MIMO)-over-the-air(OTA) evaluation. The radio wave propagation characteristics necessary for the generation of these virtual radio wave environments are set using the multiple signal classification method incorporating an RF recorder. The research discussed in this paper used these methods to analyze the effect of the multipath distortion rate on sound quality in the reception of FM broadcasts.

In recent years, the slip lock-up mechanism has been adopted widely, because of its fuel efficiency and its ability to improve NVH. This necessitates that the automatic transmission fluid (ATF) used in automatic transmissions with slip lock-up clutches requires anti-shudder performance characteristics. The test methods used to evaluate the anti-shudder performance of an ATF can be classified roughly into two types. One is specified to measure whether a μ-V slope of the ATF is positive or negative, the other is the evaluation of the shudder occurrence in the practical vehicle. The former are μ-V property tests from MERCON® V, ATF+4®, and JASO M349-98, the latter is the vehicle test from DEXRON®-III. Additionally, in the evaluation of the μ-V property, there are two tests using the modified SAE No.2 friction machine and the modified low velocity friction apparatus (LVFA).

Idling stop systems are being increasingly adopted in conventional engine vehicles as well as hybrid electric vehicles to increase fuel efficiency. When the engine starts, body vibration occurs that is caused by the rigid body eigenvalues of the power plant during initial combustion. Engine restart vibration after an idling stop is caused by the input force from the transmission, and the reaction force from the drive shaft as well as the input force from the engine. This phenomenon occurs frequently when the engine is restarted from the idling stop, the vibration is increasingly annoying to passengers. Usually, the vehicle development process is carried out in accordance with the V process. The V process divides the vehicle development process into two stages. The first stage is called the vehicle design stage to determine the characteristic. The second stage is called the vehicle verification stage to verify the performance.

The practical application of heat recovery using thermoelectrics requires the realization of reasonable cost effectiveness. Therefore, a thermoelectric generator (TEG) structure that can compatibly increase efficiency and reduce cost was investigated with the aim of enhancing cost effectiveness. To increase efficiency, a method of using a vacuum space structure to reduce the TEG size was investigated to enable installation just after the close-coupled catalyzer, which is subject to many space restrictions. It was found that by making it possible to use high temperature exhaust heat, power generation efficiency can be increased to approximately twice that of the typical under floor installation. In addition, coupled simulation of heat transfer and power generation using FEM, 1D cost effectiveness simulations, and bench tests were performed with the aim of reducing cost.

In conventional electronically controlled fuel injection systems, when the battery is inadequately charged, the small amount of electric power generated from the alternator by the kick starter operation is consumed by all electrical loads including the battery. This causes a voltage drop, hence the fuel injection system does not function due to a power shortage. To eliminate the power shortage, an installed relay circuit opens all electric loads other than the fuel injection system. This allows the fuel injection system to use all the electric power generated by the kick starter operation aided through using an additionally incorporated condenser. This type of electric power control system has been incorporated into the ECU. Thus, the control system has been realized that permits starting of an engine by using the kick-starter even when the battery is completely discharged.

Lithium-rich layered oxide, expressed as xLi2MnO3-(1-x) LiMO2 (M = Ni, Co, Mn, etc.), exhibits a high discharge capacity of 200 mAh/g or more and a high discharge voltage at a charge of 4.5 V or more. Some existing reports on cathode materials state that lithium-rich layered oxide is currently the most promising candidate as an active material for high-energy-density lithium-ion cells, but there are few reports on the degradation mechanism. Therefore, this study created a prototype cell using a lithium-rich layered cathode and a graphite anode, and analyzed the degradation mechanism due to charge and discharge. In order to investigate the causes of degradation, changes in the bulk structure and surface structure of the active material were analyzed using high-resolution X-ray diffraction (HRXRD), a transmission electron microscope (TEM), X-ray absorption fine structure (XAFS), and scanning electron microscope/energy dispersive X-ray spectroscopy (SEM-EDX).

In order to reduce emissions and enhance energy security, renewable power sources are being introduced proactively. As the fraction of these sources on a power grid grows, it will become more difficult to maintain balance between renewable power supply and coincident demand, because renewable power generation changes frequently and significantly, depending on weather conditions. As a means of resolving this imbalance between supply and demand, vehicle-to-grid (V2G) technology is being discussed, because it enables vehicles to contribute to stabilizing the power grid by utilizing on-board batteries as a distributed energy resource as well as an energy storage for propulsion. The authors have built a plug-in vehicle with a capability of backfeeding to the power grid, by integrating a bi-directional on-board AC/DC and DC/AC converter (on-board charger) and a digital communication device into the vehicle. The vehicle is interconnected to a power regulation market in the United States.

The cooling performance and the heat resistance performance of commercial vehicle are balanced with aerodynamic performance, output power of powertrain, styling, cost and many other parameters. Therefore, it is desired to predict the cooling performance and the heat resistance performance with high accuracy at the early stage of development. Among the three basic forms of heat transfer (conduction, convection and radiation), solving thermal conduction accurately is difficult, because modeling of “correct shape” and setting of coefficient of thermal conductivity for each material need many of time and efforts at the early stage of development. Correct shape means that each part should be attached correctly to generate the solid mesh with high quality. Therefore, it is more efficient and realistic method to predict the air temperature distribution around the rubber/resin part instead of using the surface temperature at the preliminary design stage.

In recent years, the reduction of CO₂ emissions is under way, and the expectancy for electrical power is getting bigger for motorcycles as well. This time, an electric motorcycle with good driving performance, adequate range and quick charging performances for business use has been developed using a small battery. The travel modes have been investigated for business applications of delivery services to classify the traveling patterns and the objectives have been settled based on them. The energy efficiency has been improved by the application of the smallest amount of battery and by the integrated power unit configuration. With this achievement, the range of 34 km (at a constant speed of 30 km/h) has been realized while maintaining the 12-degree hill-climbing departure performance when loaded with a rider and a 30 kg load, which is the requirement of performance for business use.

A new electric power steering (EPS) was developed which uses an electric motor to provide assistance. It is a system combinning the latest in power electronics and high power motor technologies. The development was aimed at enhancing the existing hydraulic power steering's energy efficiency, driver comfort as well as increasing active stability. This paper describies the overall concept of EPS and outlines the components and control strategies using electronics. The EPS was tested on a front wheel drive vehicle weighing 1000kg in front axle load. The results showed a 5.5% improvement in fuel economy. The EPS has also achieved returnability that gives the driver more moderate feelings matching the vehicle in action as well as the active stability control strategy for high speed driving.

Honda has developed the 2018 model CLARITY PLUG-IN HYBRID. Honda’s new plug-in hybrid is a midsize sedan and shares a body platform with the CLARITY FUEL CELL and the CLARITY ELECTRIC. The vehicle’s electric powertrain boosts driving performance as an electric vehicle (EV) over Honda’s previous plug-in hybrid. The CLARITY PLUG-IN HYBRID’s electric powertrain consists of a traction motor and generator built into the transmission, a Power Control Unit (PCU) positioned above the transmission, an Intelligent Power Unit (IPU) fitted under the floor, and an onboard charger fitted below the rear trunk. The PCU integrates an inverter that drives the traction motor, an inverter that drives the generator, and a DC-DC converter to boost battery voltage (referred to as a “Voltage Control Unit (VCU)” below).

A new fuel cell voltage control unit (FCVCU) has been developed for a new fuel cell vehicle (FCV). In order to simultaneously reduce the electric powertrain size and increase the driving motor power, the FCVCU is needed to boost the voltage supplied from the fuel cell (FC) stack to the driving motor. The FCVCU circuit configuration has four single-phase chopper circuits arranged in parallel to form a 4-phase interleaved circuit. The intelligent power module (IPM) is a full SiC IPM, the first known use to date in a mass production vehicle, and efficiency has been enhanced by making use of the effects of the increased frequency to reduce both the size of the unit and the loss from passive parts. In addition, a coupled inductor was used to reduce the inductor size. As a result, the inductor volume per unit power was reduced approximately 30% compared to the previous VCU inductor.

In 2002, to address environmental and energy issues, Honda began to deliver a fuel cell vehicle, the FCX. Now, Honda has developed a new model FCX, which is able to operate in cold regions with significantly enhanced driving performance, in an attempt to increase the popularity of fuel cell vehicles in the world. The new vehicle employs Hondas next-generation fuel cell stack which enables start-up and allows for power generation at - 20 ° C, and Honda has delivered new FCXs to customers where winter temperatures fall to -20 ° C--in New York state, US and Hokkaido, Japan-leading the world. As the motor power-output has been increased to 80kW increases in both the power-output of the fuel cell stack and the energy capacity of the ultra-capacitors have enabled an increased supply of power to ° the motor, resulting in significant enhancement of both initial and overtake acceleration performance.

A CVT for midsize vehicles was developed that simultaneously achieves high levels of fuel efficiency performance and driving enjoyment, and marketability enabling deployment to global markets, and support for high-torque direct injection engines. This was done by modifying the CVT for 2.4 L-class vehicles sold in Japan, expanding the ratio range, using CVTF with a high friction-coefficient that simultaneously realizes both high efficiency and a high transmission capacity. This enabled achievement of an overall length of 386.5 mm, total weight of 96.1 kg, and maximum transmission torque of 270 Nm, and also enhanced fuel efficiency by approximately 10% (EAP fuel economy label) compared to the 2008 model year Accord 5AT and approximately 5% (JC08) compared to the 2010 model year STEP WGN CVT. Thus, CVT performance was obtained that can simultaneously realize high levels of both fuel efficiency and driving enjoyment.

Honda has developed an electric powertrain for a 2017 plug-in hybrid vehicle using its second-generation SPORT HYBRID i-MMD powertrain system as a base. The application of the newly developed powertrain system realizes a long all-electric range (AER), allowing operation as an EV for almost all everyday driving scenarios, with dynamic performance making it possible for the vehicle to operate as an EV across the entire speed range, up to a maximum speed of 100 mph. The amount of assist provided by power from the batteries during acceleration has been increased, helping to downsize the engine while also balancing powerful acceleration with quietness achieved by controlling racing of the engine. In order to realize this EV performance with the second-generation SPORT HYBRID i-MMD system as the base, it was necessary to increase the power output of the DC-DC converter, taking restrictions on space into consideration.