Search Results

A Dual Piston Variable Compression Ratio (VCR) engine has been newly developed. In order to ensure the strength of the Dual Piston, the design guidelines were established. There are two advantages of this design. One is the compactness and the compatibility with a mass production engine block. Another is less power consumption required during compression ratio switching. However, the durability is a challenge for this design because of the impact load during the switching driven by the inertial force of a reciprocating piston. In order to achieve a durable configuration, it was necessary to consider the dynamics of the stress after impact, from analysis of the impacting process during the switching. The analysis of stress and deformation mode was improved in accuracy by using Computer Aided Engineering (CAE) in the designing process.

An aerodynamic styling evaluation system employed at an early automotive development stage was constructed. The system based on CFD consists of exterior model morphing, computational mesh generation, flow calculation and result analysis, and the process is automatically and successively executed by process automation software. Response surfaces and a parallel coordinates chart output by the system allow users to find a well-balanced exterior form, in terms of aerodynamics and exterior styling, in a wide design space which are often arduous to be obtained by a conventional CAE manner and scale model wind tunnel testing. The system was designed so that 5-parameter study is completed within approximately two days, and consequently, has been widely applied to actual exterior styling development. An application for a hatchback vehicle is also introduced as an actual example.

The practical application of heat recovery using thermoelectrics requires the realization of reasonable cost effectiveness. Therefore, a thermoelectric generator (TEG) structure that can compatibly increase efficiency and reduce cost was investigated with the aim of enhancing cost effectiveness. To increase efficiency, a method of using a vacuum space structure to reduce the TEG size was investigated to enable installation just after the close-coupled catalyzer, which is subject to many space restrictions. It was found that by making it possible to use high temperature exhaust heat, power generation efficiency can be increased to approximately twice that of the typical under floor installation. In addition, coupled simulation of heat transfer and power generation using FEM, 1D cost effectiveness simulations, and bench tests were performed with the aim of reducing cost.

This study aims to build a conceptual simulation used at the early stage of PHEV development. This simulation enables to design vehicle concept and fundamental architecture with regard to fuel economy, vehicle acceleration and electric range. The model based on forward-looking method comprises of plant-model and controller-model which are made by one-dimensional simulation tool “GT-SUITE” and Matlab/SIMULINK respectively. In order to automatically couple between them and to implement iterative calculations of SOC (State-of-Charge) convergence, optimization and automation tool “modeFRONTIER” was used. As a case study of this simulation, we adopted series-parallel type plug-in hybrid electric vehicle (PHEV) and demonstrated the results on fuel economy of a legislative driving cycle and 0-60mph vehicle acceleration. Moreover, procedures to identify component specifications meeting vehicle targets and requirements at the early stage of vehicle development were concretely described.

Turbine housings in car engine turbochargers, which use costly stainless steel castings, account for nearly 50% of the parts cost of a turbocharger. They are also the component which controls the competitiveness of the turbocharger, in terms of both function and cost. In this research, focusing on thermal fatigue resistance which is one of the main functions demanded of a turbine housing, achieving reduction in wall thickness while securing sufficient thermal fatigue resistance, it is possible to reduce the amount of material used in the turbine housing and aimed for cost reduction. Therefore, we built a method to quantitatively predict, using 3D FEM, the lifespan from the initiation of thermal fatigue cracking to the formation of a penetrating crack which leads to gas leakage.

The cooling performance and the heat resistance performance of commercial vehicle are balanced with aerodynamic performance, output power of powertrain, styling, cost and many other parameters. Therefore, it is desired to predict the cooling performance and the heat resistance performance with high accuracy at the early stage of development. Among the three basic forms of heat transfer (conduction, convection and radiation), solving thermal conduction accurately is difficult, because modeling of “correct shape” and setting of coefficient of thermal conductivity for each material need many of time and efforts at the early stage of development. Correct shape means that each part should be attached correctly to generate the solid mesh with high quality. Therefore, it is more efficient and realistic method to predict the air temperature distribution around the rubber/resin part instead of using the surface temperature at the preliminary design stage.

With a growing demand for high-power diesel engines, a key issue in engine development is to create efficient methods for developing highly durable cylinder heads, without having to repeat trial-and-error testing. Especially, it was difficult to accurately predict the occurrence and origin of cracks on the surfaces of cylinder heads in hot and cold cycle engine operation. This paper describes a thermal fatigue evaluation method developed by analyzing areas around the glow plug hole where cracks often occur during hot and cold cycle engine operation. To reveal the conditions of edges from which cracks were formed under engine durability tests, we used two procedures. One was estimating local temperature of edge areas based on material hardness determination, in order to compensate for the accuracy of the thermal analysis. The other was analyzing the strain amplitudes on the cylinder head surface using computer simulation.

Technology has been developed to increase the fatigue strength of powder-forged connecting rods. The fatigue strength of powder-forged materials was increased without adding special alloy components or lowering workability by adjusting the ratios of the conventional main mixed powders (iron, carbon, copper). In addition to solid solution strengthening of the ferrite using copper, reducing porosity, which is a material surface defect, is also an effective method of increasing fatigue strength. Reducing carbon content greatly reduced the occurrence of defects in the forging stage. The results of this research showed that the fatigue strength of high strength powder-forged connecting rods can be increased by 30% or more over that of conventional materials, allowing powder-forged connecting rods to be applied to even higher output and higher load engines than before.

HONDA completed research and development of the Metal V-Belt for CVTs in-house for the purpose of reducing the minimum pitch radius. The newly developed belt is essential to the compactness of a CVT and increases the speed ratio range. Increase of ring stress caused by reducing the minimum pitch radius is treated by improvement of element shape, optimizing clearance between elements and between element and ring and improving materials.(1) In this paper, the optimization of clearance between elements, heat treatment of elements and optimization of ring material are described in detail. Optimum total clearance between elements for a virgin belt is defined by test results during operation using a specially engraved gap sensor and a telemeter system. Tolerance and conditions of heat treatment for elements are optimized concerning fatigue strength of the element nose.

Nd₂Fe₁₄B sintered magnets are used in the drive motors of hybrid, electric and other vehicles. A magnet in which rare earth content is reduced by means of a localized diffusion method has been developed in order to reduce the volume of dysprosium. The distribution of the demagnetization fields in a motor is not uniform, so the necessary coercivity distribution for the magnets was quantified using Computer-Aided Engineering (CAE). Then material specifications of the localized dysprosium diffusion satisfied with this coercivity distribution was determined, and optimal manufacturing conditions including the position of dysprosium diffusion were set. The coercivity distribution in every position of the magnet using localized diffusion method was inspected. As a result, the magnet was satisfied with coercivity distribution demanded by CAE.

For detailed temperature estimates in the engine of a running motorcycle, newly researches were conducted on the method for calculation of temperature distribution using a three-dimensional (3D) thermal conductivity simulation after calculating the total balance of heat generation and heat dissipation of the engine using a one-dimensional (1D) thermal simulation. This project is targeted at air-cooled engines in which the cooling conditions vary significantly depending on the external shapes of the engines and the airflow around them. The heat balance is calculated using the 1D thermal simulation taking into account all the routes and processes for dissipation to the atmosphere of the heat that is generated by the combustion in the engine. The 1D engine cycle simulation is applied to calculate the heat transmission to the engine from the combustion. For the calculation of heat transfer within the engine, the engine components are converted to a one-dimensional model.

This paper describes the development of non-contacting detection type torque sensor that realizes a small lost motion with light weight and low cost. Pedal-equipped electric vehicles are becoming popular in recent years. In those vehicles, torque sensors are usually necessary for measuring the pedaling force to determine the motor torque. We applied an integrated sensing structure and a non-contacting scheme utilizing inverse-magnetostrictive material to minimize the lost motions. As for the sensing material, nickel-iron alloy plating was used to obtain a wide dynamic range. In the tests using the actual structure, the output linearity deterioration occurred because of the strain distribution dispersion produced by the ratchet drive structure. Therefore, the effect of this strain distribution was examined. The inverse-magnetostrictive sensing material of nickel-iron alloy plating has an extremum on its output curve.

Looking back on steering systems in more than a hundred years that have passed since the introduction of the automobile, it can be seen that original method of controlling cars pulled by animals such as horses was by reins, and early automobiles had a single push-pull bar (tiller steering). That became the steering wheel, and an indirect steering mechanism by rotating up and down caught on. While the steering wheel is the main type of steering system in use today, the team have developed the Twin Lever Steering (TLS) system controlled mainly by bi-articular muscles, making use of advancements in science and technology and bioengineering to develop based on bioengineering considerations as shown in Fig. 1. The objective of that is to establish the ultimate steering operation system for drivers. In the first report, the authors reported on results found by using race-car prototypes as shown in Fig. 2.

With the objective of establishing the ultimate steering operation system for drivers, we developed, based on bioengineering considerations, the Twin Lever Steering (TLS) system which mimicks the bi-articular muscles, as shown in Fig. 1 . The bioengineering advantages are as follows: (1) force can be exerted more easily, (2) the steering can be accomplished quickly, (3) the positioning can be done accurately, and (4) the burden on the driver can be reduced (less fatigue). The advantages of the vehicle in terms of its motion are as follows: (1) the line-traceability is improved, (2) the drift control is improved, (3) the lane-change capability is improved, and (4) the lap time and stability are improved. We would like to report on these advantages of the TLS system from a bioengineering standpoint, and also describe the results of some verification test results obtained from vehicles equipped with this new steering system.

A new nitriding technology and material technology have been developed to increase the strength of microalloyed gears. The developed nitriding technology makes it possible to freely select the phase composition of the nitride compound layer by controlling the treatment atmosphere. The treatment environment is controlled to exclude sources of supply of [C], and H2 is applied as the carrier gas. This has made it possible to control the forward reaction that decomposes NH3, helping to enable the stable precipitation of γ′-phase, which offers excellent peeling resistance. A material optimized for the new nitriding technology was also developed. The new material is a low-carbon alloy steel that makes it possible to minimize the difference in hardness between the compound layer and the substrate directly below it, and is resistant to decline in internal hardness due to aging precipitation in the temperature range used in the nitriding treatment.

In conventional CAE (Computer Aided Engineering), methods using grids, such as the finite element method and the finite volume method, are commonly used. However grids are sometimes problematic in cases of dynamic free surface flows, with large deformation or breaking. In this study, a novel three-dimensional fluid, structural analysis simulation program to reproduce the dynamic behavior of water or soil in the mechanical parts of a product equipped with a small engine was developed. This simulation program expresses water or soil as particles within boundaries having complicated configuration. These particles are then replaced with a polygon model to lower calculation load and to improve accuracy of configuration reproducibility. In the structural analysis, a breaking condition which considers the effect of soil compaction was designed to reproduce the break up of material with special characteristics such as soil.

In this research, a new wire material made using surface-reforming heat treatment was developed in order to enhance the corrosion fatigue resistance of suspension springs. The aim of surface reforming is to improve hydrogen embrittlement characteristics through grain refinement and to improve crack propagation resistance by partial softening of hardness. The grain refinement method used an α'→γ reversed transformation by rapid short-term heating in repeated induction heating and quenching (R-IHQ) to refine the crystal grain size of SAE 9254 steel spring wire to 4 μm or less. In order to simultaneously improve the fatigue crack propagation characteristics, the possibility of reducing the hardness immediately below the spring surface layer was also examined. By applying contour hardening in the second IHQ cycle, a heat affected zone (HAZ) is obtained immediately below the surface.

Improvement of engine cycle thermal efficiency is an effective way to increase engine torque and to reduce fuel consumption simultaneously. However, the extent of the improvement is limited by engine knock, which is more evident at low engine speeds when combustion flame propagation is relatively slow. To prevent engine damage due to knock, the spark ignition timing of a gasoline engine is usually controlled by a knock sensor. Therefore, an engine's ignition timing cannot be set freely to achieve best engine performance and fuel economy. Whether ignition timings for a multi-cylinder engine are the same or can be set differently for each cylinder, it is not desirable for each cylinder has big deviation from the median with respect to knock tendency. It is apparent that effective measures to improve engine knock toughness should address both uniformity of all cylinders of a multi-cylinder engine and improvement of median knock toughness.

The independent bearing cap is a cylinder block bearing structure that has high mass reduction effects. In general, this structure has low fastening stiffness compared to the rudder block structure. Furthermore, when using combination of different materials small sliding occurs at the mating surface, and fretting fatigue sometimes occurs at lower area than the material strength limit. Fretting fatigue was previously predicted using CAE, but there were issues with establishing a correlation with the actual engine under complex conditions, and the judgment criteria were not clear, so accurate prediction was a challenge. This paper reports on a new CAE-based prediction method to predict the fretting damage occurring on the bearing cap mating surface in an aluminum material cylinder block. First of all, condition a fretting fatigue test was performed with test pieces, and identification of CAE was performed for the strain and sliding amount.

Since the operation of the powertrain system and the engine speed and torque are determined in the ECU in hybrid vehicles, control parameters in these vehicles are more sensitive to a variety of performance factors than those employed in conventional vehicles. The three performance factors acceleration performance, NVH and fuel consumption in particular are in a tradeoff relationship, the calibration of control parameters in order to satisfy these performance targets entail considerable development costs. Given this, it is possible to increase the efficiency of hybrid vehicle development by determining Pareto design solutions for the three performance factors via multi-objective optimization using CAE, and selecting target performance and control parameters based on these Pareto design solutions.