Search Results

In this research, a material model was developed that has orthotropic properties with respect to in-plane damage to support finite element strength analysis of components manufactured from a randomly oriented long-fiber thermoplastic composite. This is a composite material with randomly oriented bundles of carbon fibers that are approximately one inch in length. A macroscopic characteristic of the material is isotropic in in-plane terms, but there are differences in the tension and compression damage properties. In consideration of these characteristics, a material model was developed in which the damage evolution rate is correlated with thermodynamic force and stress triaxiality. In-plane damage was assumed to be isotropic with respect to the elements. In order to validate this material model, the results from simulation and three-point bending tests of closed-hat-section beams were compared and found to present a close correlation.

In recent years, the slip lock-up mechanism has been adopted widely, because of its fuel efficiency and its ability to improve NVH. This necessitates that the automatic transmission fluid (ATF) used in automatic transmissions with slip lock-up clutches requires anti-shudder performance characteristics. The test methods used to evaluate the anti-shudder performance of an ATF can be classified roughly into two types. One is specified to measure whether a μ-V slope of the ATF is positive or negative, the other is the evaluation of the shudder occurrence in the practical vehicle. The former are μ-V property tests from MERCON® V, ATF+4®, and JASO M349-98, the latter is the vehicle test from DEXRON®-III. Additionally, in the evaluation of the μ-V property, there are two tests using the modified SAE No.2 friction machine and the modified low velocity friction apparatus (LVFA).

The PVC(poly-vinyl chloride) underbody coating was specifically designed for the automotive underfloor area in order to prevent chipping damage as well as the onset of rust propagation from a scratched point. This superior anti-chipping performance can also be achieved without increasing film thickness of the PVC by balancing film strength and adhesion strength. Also, by incorporating plastic balloons in the PVC formulation, a dried film specific gravity of less than 1.0 is achieved, and consequently a 2 kg weight reduction becomes possible when compared to conventional materials used for underbody coating.

Combined Brake System for small motorcycles has been developed. In small motorcycles, some models have a hydraulic disc brake both in the front and rear wheels but many of them have a hydraulic disc front brake and a mechanical drum rear brake. Accordingly, it was necessary to develop a new system to link the hydraulic system with the mechanical system to allow an application of Combined Brake System to these models. In this paper, a CBS having a new configuration is described where a disc brake and a drum brake are linked in a simple lever structure of an input force distributor, and an inhibitor spring at the foot pedal. With this mechanism equipped, the distribution of brake forces is controlled. When a large input force is applied, a large proportion of brake force is applied to the front brake to obtain adequate deceleration. When a mild input force is applied, which is frequently operated, the brake force proportion is large in the rear compared to the front.

A hexavalent-chromium-free metal gasket for PWC engines was developed to correspond to the ELV (End of Life Vehicle) directive. In order to enhance the adhesive property, the ion capture to trap the chloride ion, an anti-rust pigment to reform the chemical coating, and an inorganic sealer to stop the passage of chloride ion were added to the adhesive and rubber raw material. A good adhesive property and rubber physical property was obtained through the addition of an anticorrosive pigment. The rubber vulcanization condition in the manufacturing process was reviewed. As a result, without modifying the current compound coating line for mass-production, a gasket with a blistering resistance more than hexavalent chromium conversion coating equivalence and coating adhesion was developed when using salt water for engine cooling.

Regulation of automotive CO2 emissions is becoming increasingly stringent throughout the world in response to global warming. For automakers, this means a focus not only on increasing the fuel economy of powertrains, but also on reducing automotive driving resistance. High expectations are held for thermoplastic fiber-reinforced plastics (FRP) for the realization of automotive weight savings while also offering high levels of productivity and recyclability. Thermoplastic FRP crush boxes display a higher level of energy absorption performance than metal (steel, aluminum, etc.) crush boxes. This will contribute to automotive weight savings and improved package design. In the case of automotive front bumper beam systems, it is necessary to realize stable load characteristics irrespective of the use environment. It is therefore necessary to consider the effects of temperature and thermoplastic resin degradation.

Currently, there is a growing demand for application of plastic coverings for motorcycles in the market. Accordingly, decorative features for plastic coverings are increasingly important to enhance the attractiveness of exterior designs of those motorcycles. Under these circumstances, the magnetically formed decorative painting had been adopted to a mass-production model sold in Thailand in 2008. Magnetically formed decorative painting is a method in which the design patterns are formed by painting a material that contains flakes movable along with magnetic fields, while applying magnetic sheets in the ornamenting design shapes underneath the part being painted. It offers a three-dimensional appearance even though its surface has no protrusions or indentations. The degree of three-dimensionality on the paint surface appearance was defined as “plasticity” [1] (a term used in pictorial arts).

The explicit methods analysis solver LS-DYNA was used to create technology for simulating airbag deployment and plastic airbag lid tear-away in the front passenger seat. The present study clarified the mechanical properties and the transitions in fracture pattern of the material at low temperature plastic this way, an appropriate modeling method was developed and the prediction accuracy of the simulation of airbag lid tear-away on deployment was increased. Tensile testing of the material was carried out where there were differences in thickness of the tear-away section and the fracture characteristics were determined. A material model was created by analyzing changes in fracture characteristics and collapse patterns, taking into consideration the effects of strain and strain rate localization on fracture strain as well as ductile-brittle fracture transition. Next, airbags were subjected to the impactor testing.

Recently, the electronic fuel injection systems have been widely applied to small motorcycles including scooters. In the high pressure fuel lines, plastic hoses have been increasingly used instead of conventional rubber hoses. As the plastic hose is less elastic than the rubber hose, the fuel pressure pulsates more in the plastic hose. To cope with this issue, we have conducted researches on how the fuel pressure pulsation in the plastic hose affects the accuracy of fuel injection. Keeping our eyes on the pulsation damping effects derived from the changes of volume due to the expansion and contraction of hose when the pressure changes, we have established the analysis method for optimization of the inner diameter and the thickness of the hose utilizing CAE analysis. The newly-developed plastic hose is applicable to motorcycles having a single cylinder 250 cm3 engine using an injector of a high static flow rate.

Most types of paint materials currently used for motorcycles contain large amounts of VOCs (Volatile Organic Compounds). VOCs are environmental load substances, and there is a demand to reduce emissions in recent years. Many of a motorcycle's exterior parts are made of ABS (Acrylonitrile-Butadiene-Styrene) plastics (henceforth ABS) or PA (Polyamid) plastics (henceforth PA). These two plastic materials have different film adhesion mechanisms and adhesion strength. Therefore it was necessary to use different conductive primers and that's was one of the factors which made time and material losses in the painting processes. We solved those two issues, the reduction of VOCs and the common use of the same conductive primer for different parts materials, by combining two kinds of resins originally designed as the conductive primers, i.e., urethane resins with carboxylic acid groups and acrylic resins with amide groups, which are different in properties.

The reciprocating frictional test is a common approach for screening the materials of the piston and sleeve of an automobile engine. The frictional speed of this test is, however, limited mainly by the vibration of test apparatus due to the absence of damping factors in engines. Considering that the frictional velocity between the piston and sleeve reaches around 20 m/s, common test conditions at less than 2 m/s are not sufficient to understand the real phenomena at a frictional interface. We therefore developed a high-speed reciprocating test apparatus that can operate at a much higher speed range and examined two materials used for piston rings and sleeves. For the piston ring material, nitrided SUS440C was used. Plates were made of centrifugal cast iron FC250 or cast aluminum AC2B, which were coated with Nikasil. The experimental results showed that the lubrication regimes of the two plate materials were different even at the same reciprocating speeds.

Recent trends to downsize engines have resulted in lighter weight and greater compactness. At the same time, however, power density has increased due to the addition of turbocharger and other such means to supplement engine power and torque, and this has increased the thermal and mechanical load. In this kind of environment, corrosion of the copper alloy bushing (piston pin bushing) that is press-fitted in the small end of the connecting rod becomes an issue. The material used in automobile bearings, of which the bushing is a typical example, is known to undergo sulfidation corrosion through reaction with an extreme-pressure additive Zinc Dialkyldithiophosphate (ZnDTP) in the lubricating oil. However, that reaction path has not been clarified. The purpose of the present research, therefore, is to clarify the reaction path of ZnDTP and copper in an actual engine environment.

Several attempts have been reported in the past decade or so which measured the sizes of particles in lubricant oil in order to monitor sliding conditions (1). Laser light extinction is typically used for the measurement. It would be an ideal if only wear debris particles in lubricant oil could be measured. However, in addition to wear debris, particles such as air bubbles, sludge and foreign contaminants in lubricant oil are also measured. The wear debris particles couldn't have been separated from other particles, and therefore this method couldn't have been applied to measurement devices for detection when maintenance service is required and how the wear state goes on. It is not possible to grasp the abnormal wear in real time by the conventional techniques such as intermittent Ferro graphic analysis. In addition, it is no way to detect which particle size to be measured by the particle counter alone.

To develop ideal oil circuits, it was necessary to establish technology that would accurately predict lubrication oil pressure and flow rates. Therefore, the oil flow rate was predicted by applying load fluctuations, calculated using multi body dynamics, to an oil film model. In addition, the pressure loss of complex oil passages was obtained using 3-dimensional computational fluid dynamics (hereafter, “3D-CFD”). Furthermore, the pressure loss of the oil pressure switching valves and other parts that are difficult to predict using 3D-CFD were measured as single parts, and these results were linked with one-dimensional internal flow analysis to develop a prediction method for lubrication oil pressure and flow rate distributions. Verification tests were ultimately performed using a completed engine, and the results confirmed that this simulation method accurately reproduces the oil pressure and oil flow rate in each part.

In order to reduce automobile body weight and improve crashworthiness, the use of high-strength steels has increased greatly in recent years. An optimal combination of both crash safety performance and lightweight structure has been a major challenge in automobile body engineering. In this study, the Cockcroft-Latham fracture criterion was applied to predict the fracture of high-strength steels. Marciniak-type biaxial stretching tests for high-strength steels were performed to measure the material constant of the Cockcroft-Latham fracture criterion. Furthermore, in order to improve the simulation accuracy, local anisotropic parameters based on the plastic strain (strain dependent model of anisotropy) were measured using the digital image grid method and were incorporated into Hill's anisotropic yield condition by the authors. In order to confirm the validity of the Cockcroft-Latham fracture criterion, uniaxial tensile tests were performed.

A new 6-speed automatic transmission (AT) has been developed with the aim of enhancing fuel economy, raising efficiency, and achieving greater compactness. The unit was built on a parallel-shaft structure similar to the previous Honda AT, which has high torque transmission efficiency. The new AT was given more gear speeds and the ability to handle higher input torque from the engine. On the one hand, bolt structure for shaft tightening was implemented, the forward-reverse shift mechanism was placed on the input shaft and common gear trains are provided. As a result of these and other measures, the total length of the new transmission is 18 mm shorter than the previous model 5-speed AT. A multi-plate lock-up clutch (LC) structure with a separate chamber in the torque converter was also adopted so that the lock-up torque capacity could be increased and the LC control range expanded.

A simple method is frequently used to calculate a reciprocating engine’s bearing load from the measured cylinder pressure. However, it has become apparent that engine downsizing and weight reduction cannot be achieved easily if an engine is designed based on the simple method. Because of this, an actual load on a bearing was measured, and the measured load values were compared with a bearing load distribution calculated from cylinder pressure. As a result, it was found that some of actual loads were about half of the calculated ones at certain crank angles. The connecting rod’s elastic deformation was focused on as a factor behind such differences, and the rod’s deformation due to the engine’s explosion load was studied. As a result, it was found that the rod part of the engine’s connecting rod was bent by 0.2 mm and became doglegged. Additional investigation regarding these findings would allow further engine downsizing.

In recent years, adhesive bonding is increasingly being applied in the construction of vehicle frames in order to improve body stiffness and crash performance. Regarding crash performance, the behavior of impacted components is affected by the fracture energy value of the adhesive. However, the relationship between the ductility and fracture energy values under mixed-mode loadings has not been sufficiently evaluated. In this paper, the fracture energy of three structural adhesives in a static mixed-mode loading using Double Cantilever Beam (DCB) specimens is presented. To derive the fracture energy values, the Compliance Based Beam Method (CBBM) was used, which allowed for precise determination of fracture energy values. Static mixed-mode loading tests were performed in six configurations of mixed-mode loading, ranging from pure peel mode state to almost pure shear mode state.

An apparatus that automatically samples lubricating oil and measures the size distribution of particles in the oil has been developed in order to monitor the state of engines and transmissions in operation. It is a widely known fact that when an engine or transmission seizes or experiences unusual wear, comparatively large pieces of wear debris are released. The goal of the use of the apparatus is to detect these particles of wear debris, stop testing before damage occurs, and clarify the causes. Seizure was, therefore, artificially induced in a transmission, and the wear debris in the oil was closely analyzed following the test. The results showed that when the simulated seizure occurred, large, elongated particles of wear debris were produced. Similar wear debris was observed in oil recovered from the market following the seizure of a component, and at present this is believed to be a type of wear debris characteristic of seizure.

At present, measurements of running resistance are conducted outdoors as a matter of course. Because of this, the ambient temperature at the time of the measurements has a considerable impact on the measurement data. The research discussed in this paper focused on the temperature characteristic of the tires and developed a new correction technique using a special rolling test apparatus. Specifically, using a tire rolling test apparatus that made it possible to vary the ambient temperature, measurements were conducted while varying the levels of factors other than temperature that affect rolling resistance (load, inflation pressure, and speed). Next, a regression analysis was applied to the data for each factor, and coefficients for a relational expression were derived, making it possible to derive a quadratic equation for the tire rolling resistance correction formula.