Search Results

The new concept oxidation for diesel engine has been developed. It has been designed to use under circumstances of the "dry condition" of exhausted emission, which indicates low soluble organics and high dry soot concentration under high exhaust gas temperature. For the reliability and performance of catalysts in dry condition, several design concepts were established. First of all, extremely low sulfate formation on catalyst at high temperature conditions, and an improved soluble organic burning characteristics was required. A minimization of deposition of the particulate component, especially sulfate, was obtained from the adjustment of washcoat loading and material property. Six different types of catalysts have been prepared and tested in a laboratory. Diesel vehicle test showed the possibility that soluble organic could be removed mostly with minimal sulfate formation.

A new concept of misfire detection in spark ignition engines using a wide-range oxygen sensor is introduced. A wide-range oxygen sensor, installed at the confluence point of the exhaust manifold, was adopted to measure the variation in oxygen concentration in case of a misfire. The signals of the wide-range oxygen sensor were characterized over the various engine-operating conditions in order to decide the monitoring parameters for the detection of the misfire and the corresponding faulty cylinder. The effect of the sensor position, the transient response characteristics of the sensor and the cyclic variation in the signal fluctuation were also investigated. Limited response time of a commercially available sensor barely allowed to observe misfire. It was found that a misfiring could be distinguished more clearly from normal combustion through the differentiation of the sensor response signal. The differentiated signal has twin peaks for a single misfiring in a cylinder.

The introduction of inexpensive cylinder pressure sensors provides new opportunities for precise engine control. This paper presents a control strategy of spark advance and air-fuel ratio based upon cylinder pressure for spark ignition engines. In order to extend the cylinder pressure based engine control to a wide range of engine speeds, the appropriate choice of control parameters is important as well as essential. For this control scheme, peak pressure and its location for each cylinder during every engine cycle are the major parameters for controlling the air-fuel ratio and spark timing. However, the conventional method requires the measurement of cylinder pressure at every crank angle degree to determine the peak pressure and its location. In this study, the peak pressure and its location were estimated, using a multi-layer feedforward neural network, which needs only five cylinder pressure samples at -40°, -20°, 0°, 20°, and 40° after TDC.

An investigation has been performed to study the response of the front bumper beam of automobiles subjected to an external impact load. In the investigation, an aluminum shell structure is modeled as a beam, and the energy absorber of polyurethane is also modeled as statically equivalent springs attached to the beam. Castigliano's second theorem and principles of energy and momentum are then used to calculate the reaction forces and maximum deflection. Stress distribution is then calculated using the beam theory. The primary concern of the investigation is to present a procedure of how to design optimally the cross-sectional shape of the front bumper of automobiles.

Aluminum steering knuckles are widely employed for weight reduction and improvement of ride & handling performance. In this study, a high strength aluminum alloy for cast-forged knuckle was designed to achieve higher mechanical properties than those of the conventional foundry alloy. Using this alloy, high strength knuckles were manufactured and performed test of mechanical properties, suspension module strength and durability. The strength and the elongation of the developed knuckle were increased by 20% and 40%, respectively, as compared with the conventional alloy. Also this knuckle passed the static strength and durability test of the front suspension module.

Four ports which have slightly different shapes have been applied to 3-valve MPI SI engine to develop Axially Stratified Lean Combustion engine. The purpose of port modification test was to investigate the effects of swirl ratio and direction on engine performance and emissions. In the engine test injection characteristics, i.e. timing, flow rate, direction as well as port design significantly effected on the engine combustion. Especially, it was observed that injection timing was the most important factor for combustion stability, but its effect on performance has some differences in accordance with the port designs. To verify the relationship between port shape and injection timing, in-cylinder gas was sampled by high speed gas sampling device varing injection timing through whole intake and compression,. strokes at spark plug position and analyzed by gas chromatography.

In order to understand the relationship between the location of piston ring gap and instantaneous change of oil consumption during engine operation, the ring rotation and instantaneous oil consumption were measured simultaneously in a hydrogen fueled single cylinder spark ignition engine. A radioactive-tracer technique was used to measure the rotational movement of piston ring. Two kinds of isotopes(60Co and 192Ir) with different energy level were mounted to the top and 2nd rings to measure each ring's movement independently. The instantaneous oil consumption was obtained by analyzing CO2 concentration in exhaust gas. From the result of ring rotational movement, typical patterns of ring rotation were obtained as follows; Rotational movements are usually initiated by changing the operating conditions. Piston rings tend to rotate easily under low load condition. The rotation speed of ring usually ranged in 0.2∼0.4 rev/min for top ring and 0.5∼0.6 rev/min for 2nd ring.

A nano-sized PM and THC emission characteristics were investigated according to the fuel injection strategy such as a pressure and timing in the GDI engine. On the part-load condition, the particulate emissions exhibited a strong sensitivity to the injection timing. The fuel injection pressure also had a great association with the nano-particles and THC. A size of PM exhausted from the GDI engine located near 10nm on the part-load. In contrast, accumulation mode particles within 60 - 80nm mainly exhausted during the cold transient start phase. Increment of fuel injection pressure positively affected on the nano-particle and THC emissions during the start of the engine, as well.

In this research, an optical system for the detection of the flame propagation under the non-knocking and knocking conditions is developed and applied to a mass produced four cylinder SI engine. The normal flames are measured and analyzed under the steady state operating conditions at various engine speeds. For knocking cycles, the flame front propagations before and after knock occurrence are simultaneously taken with cylinder pressure data. In non-knocking and knocking cycles, flame propagation shows cycle-by-cycle variations, which are quite severe especially in the knocking cycles. The normal flame propagations are analyzed at various engine speeds, and show that the flame front on the exhaust valve side becomes faster as the engine speed increases. According to the statistical analysis, knock occurence location and flame propagation process after knock can be categorized into five different types.

Reducing unsprung mass of the car is a representative method to enhance the ride & handling performance and fuel efficiency. In this study, brake disc weight is reduced 15∼20% using a hybrid type material. The basis for this study is the separation of the friction surface and HAT(mounting part). Aluminum material is applied in the HAT for a light weight effect. Gray iron is applied in the friction surface section to maintain braking performance. Two types of joining between aluminum and cast iron are developed. One is the aluminum casting method utilizing a gray iron insert and the other is a bolted assembly method. Detailed structure, process and material are optimized using try-out & dynamometer experiments. The Reliability of this development is proved through durability (dynamometer and vehicle) testing.

To meet Euro6 regulation particulate matter MEMS sensor is suggested. This sensor detects induced charges by PM. To increase sensitivity of the sensor, surface area of the sensor is increased by MEMS process. Sensor is made by low resistive silicon. Total size is 4.3 mm x 59.4 mm x 1 mm and size of sensor part is 4.3 mm x 13 mm. On the backside of the sensor, Pt heater is fabricated to remove piled PM on sensor part. After sensor part, charge amplifier is used to measure the induced charge of the sensor. From FFT of sensor signal, it can sense 5.46 mg/m₃ of PM. In this paper, MEMS devices for exhaust system monitoring of automobiles are investigated. PM emitted from diesel engine is charged particle. Charge-induced-type PM sensor we designed can measure by real time and it doesn't need particle collection apparatus

The main contribution of this paper is to employ a sound and vibration theory in order to develop a light and cost effective plastic intercooler pipe. The intercooler pipe was composed of two rubber hoses and one aluminum pipe mounted between an ACV (Air Control Valve) and an intercooler outlet. The engineering design concept is to incorporate low-vibration type bellows and an impedance-mismatched center pipe, which replaces the rubber hoses and aluminum pipe respectively. The bellows were designed to adapt powertrain movement for high vibration transmission loss to the intercooler outlet. Also, the impedance-mismatched center pipe was implemented to increase reflected wave by using relatively higher modulus than bellows part and applying a SeCo (Sequential Coextrusion) processing method.

In order to investigate the characteristics of top ring groove deposit formation in gasoline and diesel engine, engine test and simulation test were performed. From component analysis of used oils sampled from actual running engines, oxidation and nitration for gasoline engine and soot content for diesel engine were selected as main parameters for evaluating oil degradation. In gasoline engine, deposit formation increases linearly with oxidation and nitration, and especially, oil oxidation is a dominant factor on the deposit formation rather than nitration. And, deposit formation increases gradually in low temperature ranges below 260°C even if oils are highly oxidized, but it increases rapidly if piston top ring groove temperature is above 260°C. In diesel engine, deposit formation is highly related to soot content in lubricating oils.

This session covers topics regarding new CI and SI engines and components. This includes analytical, experimental, and computational studies covering hardware development as well as design and analysis techniques. Presenter Sung Hoon Lee, Hyundai Motor Co.

The purpose of this paper is to closely examine the influence of the behavior of fuel mixture in the intake manifold on combustion characteristics, performances of engine output and exhaust emission by using a 4-stroke spark ignition engine. In case of removing the liquid film fuel flowing on the wall of the intake manifold and of not removing it, the values of combustion characteristics such as the heat release delay, the combustion delay, the rate of heat release, the burned mass fraction and the maximum combustion pressure were obtained from the analysis of pressure indicator diagram. And then, the values of engine performance and concentration of exhaust gas were obtained.

There have been strong moves in recent years to introduce the metal matrix composites concept into higher volume applications, notably the automotive field where large volume production and lower material costs are required. The wettability between reinforcing materials and base material is one of important factors for the strength of composites and its manufacture. The main objective of this paper is to establish a basic understanding of wetting phenomena in SiC/liquid aluminum and aluminum alloy systems. In the present paper, results from the sessile drop method are reported for the effects on the wetting angle, θ, of free silicon in the silicon carbide substrate and of alloying additions of silicon, copper or magnesium to the aluminum drop for the temperature range 700-900 or 1400°C in the titanium-gettered vacuum (1.3 x 10-2 / 1.3 x 10-3 Pa).