Search Results

In this work, an experimental and analysis methodology was developed to evaluate the preignition propensity of fuels and engine operating conditions in an SI engine. A heated glow plug was introduced into the combustion chamber to induce early propagating flames. As the temperature of the glowplug varied, both the fraction of cycles experiencing these early flames and the phasing of this combustion in the engine cycle varied. A statistical methodology for assigning a single-value to this complex behavior was developed and found to have very good repeatability. The effects of engine operating conditions and fuels were evaluated using this methodology. While this study is not directly studying the so-called stochastic preignition or low-speed preignition problem, it studies one aspect of that problem in a very controlled manner.

Gasoline compression ignition (GCI) offers improved efficiency by harnessing gasoline’s low reactivity to induce an extended ignition delay that promotes partial premixing of air and fuel before combustion occurs. However, enabling GCI across the full engine operating load map poses several challenges. At high load, due to the elevated pressures and temperatures of the charge mixture, the ignition delay time shrinks, leading to diminished GCI efficiency benefits. At low load, insufficient temperatures and pressures can lead to combustion instability. Variable valve actuation offers a practical solution to these challenges by enabling effective compression ratio (ECR) control. In this paper, the effects of variable intake valve closings were investigated for high load operations in a prototype heavy-duty GCI engine, using a research octane number 93 gasoline fuel. The study focused on the 50% (B50) and the 75% (B75) load conditions at 1375 RPM.

While the use of injection strategies utilizing multiple injection events for each engine cycle has become common, there are relatively few studies of the spray structure of split injection events. Optical spray measurements are particularly difficult for split injection events with a short dwell time between injections, since droplets from the first injection will obscure the end of the first and the start of the second injection. The current study uses x-ray radiography to examine the near-nozzle spray structure of split injection events with a short dwell time between the injection events. In addition, x-ray phase-enhanced imaging is used to measure the injector needle lift vs. time for split injections with various dwell timings. Near the minimum dwell time needed to create two separate injection events, the spray behavior is quite sensitive to the dwell time.

As greater emphasis is placed on the development of small fuel-efficient cars, there is a growing need to reduce the size of the inverter used in hybrid vehicles (HVs). However, semiconductor devices and other components are generating larger amounts of heat and the parts used to cool these components are becoming thinner. One issue resulting from these trends is perforations that propagate from coolant paths. This development secured corrosion resistance by controlling sacrificial corrosion protection performance, optimizing the use of Mn and Si materials to reduce susceptibility to grain-boundary corrosion, and taking a microstructural approach to the flow of the brazing filler metal. The developed material was applied to the inverter cooler of a small HV released at the end of 2011.

Clean snowmobile technology has been developed and applied to an existing commercially available snowmobile. The goals of this effort included reducing exhaust emissions to levels which are below the U.S Environmental Protection Agency (EPA) 2012 standard. Additionally, noise levels were to be reduced to below the noise mandates of 78 dB(A). Further, this snowmobile can operate using any blend of gasoline and ethanol from E20 to E30. All of these goals were achieved while keeping the cost affordable. Snowmobiling is, after all, a recreational sport; thus the snowmobile must remain fun to drive and cost effective to produce. The details of this design effort including performance data are discussed in this paper. Specifically, the effort to modify a commercially available snowmobile using a three cylinder, four-stroke engine is described. This snowmobile was modified to run on a range of ethanol blended fuels using a closed-loop engine control system.

Investigating combustion characteristics of oxygenated gasoline and gasoline blended ethanol is a subject of recent interest. The non-linearity in the interaction of fuel components in the oxygenated gasoline can be studied by developing chemical kinetics of relevant surrogate of fewer components. This work proposes a new reduced four-component (isooctane, heptane, toluene, and ethanol) oxygenated gasoline surrogate mechanism consisting of 67 species and 325 reactions, applicable for dynamic CFD applications in engine combustion and sprays. The model introduces the addition of eight C1-C3 species into the previous model (Li et al; 2019) followed by extensive tuning of reaction rate constants of C7 - C8 chemistry. The current mechanism delivers excellent prediction capabilities in comprehensive combustion applications with an improved performance in lean conditions.

Onboard reforming has been proposed as a strategy for improving spark-ignited (SI) engine efficiency through knock reduction, dilution limit extension, improved thermodynamic gas properties, and thermochemical exhaust enthalpy recuperation. One approach to onboard fuel reforming is to combust fuel in the engine cylinder under rich conditions, producing a hydrogen-rich reformate gas--which can subsequently be recirculated into the engine. Hydrogen is the preferred product in this process due to its high flame speed and knock resistance, compared with other reformate constituents. In this work, the effects of engine operation, fuel composition and water injection were evaluated for their effect on reformate gas composition produced under rich combustion conditions. Engine parameters, including intake pressure, intake temperature, combustion phasing, and valve timing all had no significant impact on hydrogen yield at a given equivalence ratio.

Near-term advances in spark ignition (SI) engine technology (e.g., variable value lift [VVL], gasoline direct injection [GDI], cylinder deactivation, turbo downsizing) for passenger vehicles hold promise of delivering significant fuel savings for vehicles of the immediate future. Similarly, trends in transmissions indicate higher (8-speed, 9-speed) gear numbers, higher spans, and a focus on downspeeding to improve engine efficiency. Dual-clutch transmissions, which exhibit higher efficiency in lower gears, than the traditional automatics, and are being introduced in the light-duty vehicle segment worldwide. Another development requiring low investment and delivering immediate benefits has been the adaptation of start-stop (micro hybrids or idle engine stop technology) technology in vehicles today.

Automotive manufacturers are facing continuously changing Global environment. Traditionally, these manufacturers relied on structural and general durability tests to validate vehicles. For these tests to remain representative of customer usage in a Global environment, the overall surface conditions of the Global road systems must be studied. Understanding and classifying these road systems conditions is an important step in dealing with vehicle durability in the Global environment. In this paper, an approach to mapping the world road systems into Established Roads (ER) and Developing Roads (DR), utilizing Statistical Discriminant Analysis (SDA), is presented. The classification of Global regions as DR and ER road systems can be effectively used to recommend appropriate development and validation tests for each road system. A few examples are presented to demonstrate how the ER vs.

This research investigates the combustion characteristics and engine performance of a conventional non-ethanol gasoline with a research octane number of 91(RON 91) and a higher reactivity RON80 gasoline under mixing-controlled combustion. The work was conducted in a model year 2013 Cummins ISX15 heavy-duty diesel engine. A split fuel injection strategy was developed to address the long ignition delay and high maximum pressure rise rate for the two gasoline fuels. Using the split fuel injection strategy, steady-state NOx sweeps were conducted at 1375 rpm with a load sweep from 5 to 15 bar BMEP. At 5 and 10 bar BMEP, both gasolines consistently exhibited lower soot levels than ULSD with the reduction more pronounced at 5 bar BMEP. 3-D CFD combustion simulation suggested that the higher volatility and lower viscosity of gasoline fuels can help improve the in-cylinder air utilization and therefore reduce the presence of fuel-rich regions in the combustion chamber.

The low-NOx standard for heavy-duty trucks proposed by the California Air Resources Board will require rapid warm-up of the aftertreatment system. Several different engine technologies are being considered to meet this need. In this study, a 1-D engine model was first used to evaluate several individual control strategies capable of increasing the exhaust enthalpy and decreasing the engine-out NOX over the initial portion of the cold start FTP cycle. The additional fuel consumption resulting from these strategies was also quantified with the model. Next, several of those strategies were combined to create a hypothetical aftertreatment warm-up mode for the engine. The model was then used to evaluate potential benefits of an air gap manifold (AGM) and two different turbine by-pass architectures. The detailed geometry of the AGM model was taken into account, having been constructed from a real prototype design.

Gasoline compression ignition (GCI) has been shown to offer benefits in the NOx-soot tradeoff over conventional diesel combustion while still achieving high fuel efficiency. However, due to gasoline’s low reactivity, it is challenging for GCI to attain robust ignition and stable combustion under cold operating conditions. Building on previous work to evaluate glow plug-assisted GCI combustion at cold idle, this work evaluates the use of a spark plug to assist combustion. The closed-cycle 3-D CFD model was validated against GCI test results at a compression ratio of 17.3 during extended cold idle operation under laboratory-controlled conditions. A market representative, ethanol-free, gasoline (RON92, E0) was used in both the experiment and the numerical analysis. Spark-assisted simulations were performed by incorporating an ignition model with the spark energy required for stable combustion at cold start.

Fuels in the gasoline auto-ignition range (Research Octane Number (RON) > 60) have been demonstrated to be effective alternatives to diesel fuel in compression ignition engines. Such fuels allow more time for mixing with oxygen before combustion starts, owing to longer ignition delay. Moreover, by controlling fuel injection timing, it can be ensured that the in-cylinder mixture is “premixed enough” before combustion occurs to prevent soot formation while remaining “sufficiently inhomogeneous” in order to avoid excessive heat release rates. Gasoline compression ignition (GCI) has the potential to offer diesel-like efficiency at a lower cost and can be achieved with fuels such as low-octane straight run gasoline which require significantly less processing in the refinery compared to today’s fuels.

The oil flow in the oil ring groove was observed in order to improve the oil ejection efficiency in the oil ring groove. The oil flow was visualized with a clear head piston using fluorescing agent and particles under motoring condition. The influences of oil ring specification on the direction and the velocity of the oil flow were evaluated. The velocity of the oil ring with oil vent holes was faster than that of the oil ring without oil vent holes. In the case of the oil ring with vent holes, the reverse flow of the oil toward the front side was observed in the back clearance. Therefore, oil vent holes can change the oil flow and improve the oil ejection efficiency in the oil ring groove.

In recent years, engine control systems have become more and more complex because of the growing pressure to develop technical innovations due to social pressures such as global warming and the depletion of fossil fuels. On the other hand, products must be launched on the market in a timely manner and at low cost. For these reasons, calibration processes have become more sophisticated. It is possible to improve the efficiency of calibration by making good use of models, and a calibration process that incorporates models is called model based calibration (MBC). MBC is a valid means of reducing the number of measurement points to some extent by statistical engine modeling and design of experiment (DoE) methodology which places measurement points in order to maximize modeling accuracy. However, it is still necessary to spend much time carrying out boundary detection testing before DoE.

National concerns over energy consumption and emissions from the transportation sector have prompted regulatory agencies to implement aggressive fuel economy targets for light-duty vehicles through the U.S. National Highway Traffic Safety Administration/Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) program. Automotive manufacturers have responded by bringing competitive technologies to market that maximize efficiency while meeting or exceeding consumer performance and comfort expectations. In a collaborative effort among Toyota Motor Corporation, Argonne National Laboratory (ANL), and the National Renewable Energy Laboratory (NREL), the real-world savings of one such technology is evaluated. A commercially available Toyota Highlander equipped with two-phase cold storage technology was tested at ANL’s chassis dynamometer testing facility.

In this study a detailed 1-D engine system model coupled with 3-D computational fluid dynamics (CFD) analysis was used to investigate the air system design requirements for a heavy duty diesel engine operating with low reactivity gasoline-like fuel (RON70) under partially premixed combustion (PPC) conditions. The production engine used as the baseline has a geometric compression ratio (CR) of 17.3 and the air system hardware consists of a 1-stage variable geometry turbine (VGT) with a high pressure exhaust gas recirculation (HP-EGR) loop. The analysis was conducted at six engine operating points selected from the heavy-duty supplemental emissions test (SET) cycle, i.e., A75, A100, B25, B50, B75, and C100. The engine-out NOx target was set at 1 g/hp-hr (1.34 g/kWh) to address a future hypothetical tailpipe NOx limit of 0.02 g/hp-hr (0.027 g/kWh) while an engine-out particulate matter (PM) target of 0.01 g/hp-hr (0.013 g/kWh) was selected to comply with existing EPA 2010 regulations.

A detailed study of various air system configurations has been conducted for a prototype gasoline compression ignition (GCI) engine using a Cummins MY2013 ISX15 heavy-duty diesel engine as the base platform. The study evaluated the configurations with the assumption that RON80 gasoline would be used as the fuel and the combustion chamber would have a geometric compression ratio (CR) of 16.5. Using 3-D computational fluid dynamics (CFD) simulations, a high efficiency & low engine-out NOx GCI combustion recipe was developed across the five engine operating points from the heavy-duty Supplemental Emissions Test (SET) cycle: A100, B25, B50, B75, and C100. The CFD generated air-thermal boundary conditions and the combustion burn-rate & injector rate-of-injection profiles were imported into a calibrated 1-D engine model for the air-handling systems analysis.

Fuel stratification effects on the combustion and emissions behaviors for partially premixed compression ignition (PPCI) combustion of a high reactivity gasoline (research octane number of 80) was investigated using the third generation Gasoline Direct-Injection Compression Ignition (Gen3 GDCI) multi-cylinder engine. The PPCI combustion mode was achieved through a double injection strategy. The extent of in-cylinder fuel stratification was tailored by varying the start of second fuel injection timing (SOIsecond) while the first fuel injection event was held constant and occurred during the intake stroke. Based on the experimental results, three combustion characteristic zones were identified in terms of the SOIsecond - CA50 (crank angle at 50% cumulative heat release) relationship: (I) no response zone (HCCI-like combustion); (II) negative CA50 slope zone: (early PPCI mode); and (III) positive CA50 slope zone (late PPCI mode).