Search Results

Pollutants emissions from transportation have become a major focus of environmental concerns in the last decades. Many alternative fuels are under consideration, among which Natural Gas as fossil resource offering an advantageous potential to reduce local emissions. The European Commission has set an objective of 10% of Natural Gas consumption for the transport sector by 2020. In a sustainable development view, both vehicle emissions and energy supply chain analysis from well to wheel must be addressed. Even if the main focus today is on CO2 emissions, it is interesting to evaluate the pollutant emissions of the whole Well to Wheel chain. Besides, as the potential of reducing pollutant emissions of vehicle (due to the improvement of engines and severization of norms), looking at pollutant emissions of the Well to Tank part of the chain could show the possible further improvements. Former studies exist, comparing Natural Gas to conventional and non conventional fuels.

Compressed natural gas (CNG) is considered as one of the most promising alternative fuels for transportation due to its ability to reduce greenhouse gas emissions (CO2, in particular) and its abundance. An earlier study from IFP has shown that CNG has a considerable potential when used as a fuel for a dedicated downsized turbo-charged SI engine on a small urban vehicle. To take further advantage of CNG assets, this approach can be profitably extended by adding a small secondary (electrical) power source to the CNG engine, thus hybridizing the powertrain. This is precisely the focus of the new IFP project, VEHGAN, which aims to develop a mild-hybrid CNG prototype vehicle based on a MCC smart car equipped with a reversible starter-alternator and ultra-capacitors (Valeo Starter Alternator Reversible System, StARS).

The simultaneous reduction of engine-out nitrogen oxide (NOx) and particulate emissions via low-temperature combustion (LTC) strategies for compression-ignition engines is generally achieved via the use of high levels of exhaust gas recirculation (EGR). High EGR rates not only result in a drastic reduction of combustion temperatures to mitigate thermal NOx formation but also increases the level of pre-mixing thereby limiting particulate (soot) formation. However, highly pre-mixed combustion strategies such as LTC are usually limited at higher loads by excessively high heat release rates leading to unacceptable levels of combustion noise and particulate emissions. Further increasing the level of charge dilution (via EGR) can help to reduce combustion noise but maximum EGR rates are ultimately restricted by turbocharger and EGR path technologies.

With a high thermal efficiency and low CO2 (carbon dioxide) emissions, Diesel engines become leader of transport market. However, the exhaust-gas legislation evolution leads to a drastic reduction of NOx (nitrogen oxide) standards with very low particulate, HC (unburned hydrocarbons) and CO (carbon monoxide) emissions, while combustion noise and fuel consumption must be kept under control. The reduction of the volumetric compression ratio (CR) is a key factor to reach this challenge, but it is today limited by the capabilities to provide acceptable performances during very cold operation: start and idle below −10°C. This paper focuses on the understanding of the main parameter’s impacts on cold operation. Effects of parameters like hardware configuration and calibration optimization are investigated on a real 4 cylinder Diesel 14:1 CR engine, with a combination of specific advanced tools.

Currently, the development of higher specific output and higher efficiency S.I. engines requires better control and knowledge of knock mechanisms. As it is not easily possible to instrument an engine to determine the beginning of fuel auto-ignition, knock modeling by means of 3D CFD simulation, can be a powerful tool to understand and try to avoid this phenomenon [1, 2, 3]. The objectives of the work described in this paper are to develop and validate a simple model of auto-ignition. This model, developed at IFP, is implemented in the 3D CFD code KMB [4, 5]. It is based on an AnB model [6, 7] which creates a ‘precursor’ species transported with the flow in the combustion chamber. When its concentration reaches a limiting value, the auto-ignition phenomenon occurs.

Recent developments on highly downsized spark ignition engines have been focused on knocking behaviour improvement and the most advanced technologies combination can face up to 2.5 MPa IMEP while maintaining acceptable fuel consumption. Unfortunately, knocking is not the only limit that strongly downsized engines have to confront. The improvement of low-end torque is limited by another abnormal combustion which appears as a random pre-ignition. This violent phenomenon which emits a sharp metallic noise is unacceptable even on modern supercharged gasoline engines because of the great pressure rise that it causes in the cylinder (up to 20 MPa). The phases of this abnormal combustion have been analysed and a global mechanism has been identified consisting of a local ignition before the spark, followed by a propagating phase and ended by a massive auto-ignition. This last step finally causes a steep pressure rise and pressure oscillations.

Due to their high thermal efficiency coupled with low CO2 emissions, Diesel engines are promised to an increasing part of the transport market if their NOx and particulate emissions are reduced. Today, adequate after-treatments, NOx and PM traps are under industrialization with still concerns about fuel economy, robustness, sensitivity to fuel sulfur and cost because of their complex and sophisticated strategy. New combustion process such as Homogeneous Charge Compression Ignition (HCCI) are investigated for their potential to achieve near zero particulate and NOx emissions. Their main drawbacks are too high hydrocarbons (HC) and carbon monoxide (CO) emissions, combustion control at high load and then limited operating range and power output. As an answer for challenges the Diesel engine is facing, IFP has developed a combustion system able to reach near zero particulate and NOx emissions while maintaining performance standards of the D.I Diesel engines.

The introduction of alternative fuels is crucial to limit greenhouse gases. CNG is regarded as one of the most promising clean fuels given its worldwide availability, its low price and its intrinsic properties (high knocking resistance, low carbon content...). One way to optimize dedicated natural gas engines is to improve the CNG slow burning velocity compared to gasoline fuel and allow lean burn combustion mode. Besides optimization of the combustion chamber design, hydrogen addition to CNG is a promising solution to boost the combustion thanks to its fast burning rate, its wide flammability limits and its low quenching gap. This paper presents an investigation of different methane/hydrogen blends between 0% and 40 vol. % hydrogen ratio for three different combustion modes: stoichiometric, lean-burn and stoichiometric with EGR.

Facing the CO2 emission reduction challenge, the combination of downsizing and turbocharging appears as one of the most promising solution for the development of high efficiency gasoline engines. In this context, as knock resistance is a major issue, limiting the performances of turbocharged downsized gasoline engines, fuel properties are more than ever key parameters to achieve high performances and low fuel consumption's levels. This paper presents a combustion study carried out into the GSM consortium of fuel quality effects on the performances of a downsized turbocharged Direct Injection SI engine. The formulation of two adapted fuel matrix has allowed to separate and evaluate the impacts of three major fuel properties: Research Octane Number (RON), Motor Octane Number (MON) and Latent Heat of Vaporization (LHV). Engine tests were performed on a single cylinder engine at steady state operating condition.

Latest emissions standards impose very low NOx and particle emissions that have led to new Diesel combustion operating conditions, such as low temperature combustion (LTC). The principle of LTC is based on enhancing air fuel mixing and reducing combustion temperature, reducing raw nitrogen oxides (NOx) and particle emissions. However, new difficulties have arisen. LTC is typically achieved through high dilution rates and low CR, resulting in increased auto-ignition delay that produces significant noise and deteriorates the combustion phasing. At the same time, lower combustion temperature and reduced oxygen concentration increases hydrocarbon (HC) and carbon oxide (CO) emissions, which can be problematic at low load. Therefore, if LTC is a promising solution to meet future emission regulations, it imposes a new emissions, fuel consumption and noise trade-off. For this, the injection strategy is the most direct mean of controlling the heat release profile and fuel air mixture.

Modelling small and large scale fluctuations of fuel distribution is of high interest for stratified direct injection spark ignition (DISI) engines. Homogeneous combustion models need to be extended or replaced in order to account for these fluctuations. They are presently neglected in most engine simulations. Effects of mean fuel/air equivalence ratio gradient have been recently included in previous homogeneous mixture approaches. To account for local fluctuations of mixture composition, the new model ECFM-Z has been developed on the basis of recent Direct Numerical Simulation results and Coherent Flame Surface modelling. The model has been implemented in a CFD code (KMB) The influence of mixture fraction is integrated in the Extended Coherent Flame Surface combustion model. The model is based on a conditional approach. Unburnt hydrocarbons produced by lean flame local extinctions are taken into account.

Among the existing concepts to help improve the efficiency of spark ignition engines on low load operating points, Controlled Auto-Ignition™ (CAI™) is an effective way to lower both fuel consumption and pollutant emissions at part load without major modifications of the engine design. The CAI™ concept is founded on the auto-ignition of a highly diluted gasoline-based mixture in order to reach high indicated efficiency and low pollutant emissions through a low temperature combustion. Previous research works have demonstrated that the valve strategy is an efficient way to control the CAI™ combustion mode. Not only the valve strategy has an impact on the amount of trapped burnt gases and their temperature, but also different valve strategies can lead to equivalent mean in-cylinder conditions but clearly differentiated combustion timing or location. This is thought to be the consequence of local mixture variations acting in turn on the chemical kinetics.

Among the existing concepts that help to improve the efficiency of spark ignition engines at part load, Controlled Auto-Ignition™ (CAI™) is an effective way to lower both fuel consumption and pollutant emissions without major modifications of the engine design. The CAI™ concept is based on the auto-ignition of a fuel mixture highly diluted with burnt gases in order to achieve high indicated efficiency and low pollutant emissions through low temperature combustion. In a 4-stroke engine, large amounts of burnt gases can be trapped in the cylinder by re-breathing them through the exhaust ports during the intake stroke using a 2-step exhaust valve-lift profile. The interaction between the intake and exhaust flows during the intake stroke was identified as a key parameter to control the subsequent combustion in a CAI™ PFI engine. Consequently, the intake valve-lift profile as well as the exhaust re-opening profile can potentially be used as control parameters for this combustion mode.

Among the existing concepts that help to improve the efficiency of spark ignition engines at part load, Controlled Auto-Ignition™ (CAI™) is an effective way to lower both fuel consumption and pollutant emissions without major modifications of the engine design. The CAI™ concept is based on the auto-ignition of a fuel mixture highly diluted with burnt gases in order to achieve high indicated efficiency and low pollutant emissions through low temperature combustion. Large amounts of burnt gases can be trapped in the cylinder by re-breathing them through the exhaust ports during the intake stroke. For that, a 2-step exhaust valve-lift profile is used. The interaction between the intake and exhaust flows during the intake stroke was identified as a key parameter to control the subsequent combustion in a CAI™ port fuel injected (PFI) engine.

The purpose of the 4-SPACE (4-Stroke Powered gasoline Auto-ignition Controlled combustion Engine) industrial research project is to research and develop an innovative controlled auto-ignition combustion process for lean burn automotive gasoline 4-stroke engines application. The engine concepts to be developed could have the potential to replace the existing stoichiometric / 3-way catalyst automotive spark ignition 4-stroke engines by offering the potential to meet the most stringent EURO 4 emissions limits in the year 2005 without requiring DeNOx catalyst technology. A reduction of fuel consumption and therefore of corresponding CO2 emissions of 15 to 20% in average urban conditions of use, is expected for the « 4-SPACE » lean burn 4-stroke engine with additional reduction of CO emissions.

An unified model with a single set of kinetic parameters has been proposed for modeling laminar flame velocities of several alkanes using detailed kinetic mechanisms automatically generated by the EXGAS software. The validations were based on recent data of the literature. The studied compounds are methane, ethane, propane, n-butane, n-pentane, n-heptane, iso-octane, and two mixtures for natural gas and surrogate gasoline fuel. Investigated conditions are the following: unburned gases temperature was varied from 300 to 600 K, pressures from 0.5 to 25 bar, and equivalence ratios range from 0.4 to 2. For the overall studied compounds, the agreement between measured and predicted laminar burning velocities is quite good.

Due to increasingly stringent regulations, reduction of pollutant emissions and consumption are currently two major goals of the car industry. One way to reach these objectives is to enhance the management of the engine in order to optimize the whole combustion process. This requires the development of complex control strategies for the air and the fuel paths, and for the combustion process. In this context, engine 0D modelling emerges as a pertinent tool for investigating and validating such strategies. Indeed, it represents a useful complement to test bench campaigns, on the condition that these 0D models are accurate enough and manage to run quite fast, eventually in real time. This paper presents the different steps of the design of a high frequency 0D simulator of a downsized turbocharged Port Fuel Injector (PFI) engine, compatible with real time constraints.

In the whole engine development process, 0D/1D simulation has become a powerful tool, from conception to final calibration. Within the context of control strategy design, a turbocharged spark ignition (SI) engine with variable camshaft timing has been modelled on the AMESim platform. This paper presents the different models and the methodology used to design, calibrate and validate the simulator. The validated engine model is then used for engine control purposes related to downsizing concept. Indeed, the presented control strategy acts on the in-cylinder trapped mass, the in-cylinder burnt gas fraction and the air scavenging from the intake to the exhaust. Consequently, it permits to reduce not only the fuel consumption and pollutant emissions but also to improve the transient response of the turbocharger

Diversifying energy resources and reducing greenhouse gas emissions are key priorities in the forthcoming years for the automotive industry. Currently, among the different solutions, sustainable biofuels are considered as one of the most attractive answer to these issues. This paper deals with the vehicle application of an innovative diesel fuel formulation using Ethanol to tackle these future challenges. The main goal is to better understand the impact of using biofuel blends on engine behavior, reliability and pollutants emissions. This alternative oxygenated fuel reduces dramatically particulate matter (PM) emissions; this paves the way to improve the NOx/PM/CO₂ trade-off. Another major interest is to avoid adding a particulate filter in the exhaust line and to avoid modifying powertrain and vehicle hardware and therefore to minimize the overall cost to fulfill upcoming emission regulations.

Air quality improvement, especially in urban areas, is one of the major concerns for the coming years. For this reason, car manufacturers, equipment manufacturers and refiners have explored development issues to comply with increasingly severe anti-pollution requirements. In such a context, the identification of the most promising improvement options is essential. A research program, carried out by IFP (Institut Français du Pétrole), and supported by the French Ministry of Industry, IFP, PSA-Peugeot-Citroën, Renault and RVI (Renault Véhicules Industriels), has been built to study this point. It is based on a three years program with different steps focused on new engine technologies which will be available in the next 20 years in order to answer to more and more severe pollutant and CO2 emission regulations. This program is divided into three main parts: the first one for Diesel car engines, the second for Diesel truck engines and the third for spark ignition engines.