Search Results

Premixed charged compression ignition (PCCI) is a promising low temperature combustion strategy for achieving a simultaneous reduction of oxides of nitrogen (NOx) and soot emissions in diesel engines. However, early direct injection results in a significant penalty in fuel economy, high unburned hydrocarbon (HC), and carbon monoxide (CO) emissions, especially in small-bore diesel engines. In the present work, computational fluid dynamic (CFD) investigations are carried out in a small-bore diesel engine using a commercial CFD software, CONVERGE. The computational models are validated with experimental results at two different load conditions, 20% and 40% of rated load. The validated models are used to carry out parametric investigations on the effects of fuel injection parameters, namely the start of fuel injection timing, injection pressure, and spray cone angle on PCCI combustion.

Among the various Low Temperature Combustion (LTC) strategies, Homogeneous Charge Compression Ignition (HCCI) is most promising to achieve near zero oxides of nitrogen (NOx) and particulate matter emissions owing to higher degree of homogeneity and elimination of diffusion phase combustion. However, one of its major limitations include a very narrow operating load range owing to misfire at low loads and knocking at high loads. Implementing HCCI in small light duty air cooled diesel engines pose challenges to eliminate misfire and knocking problems owing to lower power output and air cooled operation, respectively. In the present work, experimental investigations are done in HCCI mode in one such light duty production diesel engine most widely used in agricultural water pumping applications. An external mixture preparation based diesel HCCI is implemented in the test engine by utilizing a high-pressure port fuel injection system, a fuel vaporizer and an air preheater.

The presence of unsaturated methyl esters in biodiesel makes it susceptible to oxidation and fuel quality degradation upon long-term storage. In the present work, the effects of oxidation of Karanja biodiesel upon long-term storage on the combustion and emission characteristics of a heavy-duty truck diesel engine are studied. The Karanja biodiesel is stored for one year in a 200 litres steel barrel at room conditions to mimic commercial storage conditions. The results obtained show that compared to diesel, the start of injection of fresh and aged biodiesels are advanced by ~2-degree crank angle, and the ignition delay time is reduced. Aged biodiesel showed a slightly smaller ignition delay compares to fresh biodiesel. The fuel injection and combustion characteristics of fresh and aged biodiesels were similar at all the load conditions. Both fresh and aged biodiesels produced higher oxides of nitrogen (NOx) and lower smoke emissions compared to diesel.

For controlling oxides of nitrogen (NOx) and particular matter (PM) emissions from diesel engines, various fuel and combustion mode modification strategies are investigated in the past. Low temperature combustion (LTC) is an alternative combustion strategy that reduces NOx and PM emissions through premixed lean combustion. Dual fuel reactivity-controlled compression ignition (RCCI) is a promising LTC strategy with better control over the start and end of combustion because of reactivity and equivalence ratio stratification. However, the unburned hydrocarbon (HC) and carbon monoxide (CO) emissions are significantly higher in RCCI, especially at part-load conditions. The present work intends to address this shortcoming by utilizing oxygenated alternative fuels. Considering the limited availability and higher cost, replacing conventional fuels completely with alternative fuels is not feasible.

In-cylinder emission control methods for simultaneous reduction of oxides of nitrogen (NOx) and particulate matter (PM) are gaining attention due to stringent emission targets and the higher cost of after-treatment systems. In addition, there is a renewed interest in using carbon-neutral biodiesel due to global warming concerns with fossil diesel. The bi-directional NOx-PM trade-off is reduced to a unidirectional higher NOx emission problem with biodiesel. The effect of water injection with biodiesel with low water quantities is relatively unexplored and is attempted in this investigation to mitigate higher NOx emissions. The water concentrations are maintained at 3, 6, and 9% relative to fuel mass by varying the pulse width of a low-pressure port fuel injector. Considering the corrosive effects of water at higher concentrations, they are maintained below 10% in the present work.

Premixed Charge Compression Ignition (PCCI) is one of the most promising low temperature combustion (LTC) strategies to achieve near zero oxides of nitrogen (NOx) and particulate matter (PM) emissions along with higher thermal efficiency. One of the major problems in diesel PCCI is a narrow operating load range because of very early ignition and knocking combustion at higher loads owing to higher reactivity of diesel fuel. Further, low volatile diesel resist vaporization, resulting in fuel spray wall wetting and higher unburned emissions in PCCI. Thus, high reactivity and low volatility of diesel fuel make it not suitable for PCCI combustion. The present work attempts to address these limitations, by blending diesel with high volatile and low reactive fuels, viz. gasoline and butanol at 10% and 20% blend levels by volume.

Extensive experimental investigations done over a decade in different engine types demonstrated the capability of achieving high efficiency along with low levels of oxides of nitrogen (NOx) and soot emissions with low temperature combustion (LTC) modes. However, the commercial application of LTC strategies requires several challenges to be addressed, including precise ignition timing control, reducing higher unburned hydrocarbon (UHC) and carbon monoxide (CO) emissions. The lower exhaust gas temperatures with LTC operation pose severe challenges for after-treatment control systems. Among the available LTC strategies, Reactivity Controlled Compression Ignition (RCCI) has emerged as the most promising strategy due to better ignition timing control with higher thermal efficiency. Nevertheless, the complexity of engine system hardware due to the dual fuel injection system and associated controls, high HC and CO emissions are the major limiting factors in RCCI.

In the present work, a relative comparison of addition of water to diesel through emulsion and fumigation methods is explored for reducing oxides of nitrogen (NOx) and smoke emissions in a production small bore diesel engine. The ratio of water to diesel was kept the same in both the methods at a lower concentration of 3% by mass to avoid any adverse effects on the engine system components. The experiments were conducted at a rated engine speed of 1500 rpm under varying load conditions. For engine studies using emulsion fuels, kinetically stable water-in-diesel nanoemulsions were prepared with 3% water concentration by mass of the total sample. The emulsion fuels formulated using commercial surfactants were transparent in appearance. The droplet size of the nanoemulsions was characterized using dynamic light scattering technique.

The Homogeneous Charge Compression Ignition (HCCI) combustion eliminates the issues of higher particulate matter and nitrogen oxides emissions that prevail in the traditional compression ignition (CI) combustion mode. The complete replacement of traditional fuels with renewable fuels for internal combustion engines is challenging because significant infrastructure changes in the production and delivery systems are required to ensure renewable fuel availability and economic feasibility. Thus, the use of renewable acetone blended with traditional gasoline has been proposed in the present study to smoothen the transition from the traditional CI to the HCCI engines. HCCI experiments were performed in a light-duty diesel engine at 1500 rpm rated speed. By varying the volumetric proportion of the acetone in the gasoline from 20% to 40%, the HCCI engine load range from 20%-60% was achieved, significantly higher than the limited diesel HCCI load range of 20%-38%.

Over the years, much progress has been made in automotive vehicle technology to achieve high efficiency and clean combustion. Reactivity controlled compression ignition (RCCI) is one of the most widely studied high-efficiency, clean combustion strategies. However, complex dual-fuel injection systems and associated controls, high unburned hydrocarbon (UHC), and carbon monoxide (CO) emissions limit RCCI use in practical applications. Recently, single fuel RCCI strategies are gaining more attention as the above shortcomings are effectively addressed. Homogeneous charge with direct injection (HCDI) is a single fuel RCCI strategy that results in high thermal efficiency and lower UHC and CO emissions. In HCDI, the port-injected diesel fuel vapour and air are inducted during the intake stroke and ignited with direct-injected diesel fuel near the end of the compression stroke. However, high oxides of nitrogen (NOx) make HCDI less viable for practical applications.

In order to comply with the stringent future emission mandates of automotive diesel engines it is essential to deploy a suitable combination of after treatment devices like diesel oxidation catalyst (DOC), diesel particulate filter (DPF) and DeNox converter (Lean NOx Trap (LNT) or Selective Catalytic reduction (SCR) system). Since arriving at a suitable strategy through experiments will involve deploying a lot of resources, development of well-tuned simulation models that can reduce time and cost is important. In the first phase of this study experiments were conducted on a single cylinder light duty diesel engine fitted with a diesel oxidation catalyst (DOC) at thirteen steady state mode points identified in the NEDC (New European Driving cycle) cycle. Inlet and exit pressures and temperatures, exhaust emission concentrations and catalyst bed temperature were measured. A one dimensional simulation model was developed in the commercial software AVL BOOST.