Search Results

This experimental study was aimed at improving a two-stroke S.I engine by injecting gasoline with air assistance through the cylinder barrel. Experimentally obtained performance and emission parameters of the engine at 25% and 100% throttle positions were analyzed at 3000 rpm. The timing of air assisted injection was optimized at 25% throttle and 3000 rpm. The performance and emissions of the engine were compared with those obtained with an optimized manifold injection system. In all cases the best spark timing was used. At 25% throttle although the thermal efficiency was increased only slightly, there was a significant reduction in HC emissions to 6.63 g/kW-h with cylinder barrel injection from 10.69 g/kW-h with manifold injection due to reduced short circuiting of the fuel. There was a reduction in NO emissions as well with cylinder barrel injection. Comparisons were made at the point of highest thermal efficiency at 100% throttle also.

The present research explores the application of biodiesel fuel in a stationary agricultural engine operated under the Homogenous charge compression ignition (HCCI) mode. To achieve HCCI combustion, a fuel vaporizer and a high-pressure port fuel injection system are employed to facilitate rapid evaporation of the biodiesel fuel. The low volatility of biodiesel is one of the significant shortcomings, which makes it inevitable to use a fuel vaporizer at 380oC. Consequently, the charge temperature is high enough to promote advanced auto-ignition. Further, the high reactivity of biodiesel favors early auto-ignition of the charge. Besides, biodiesel exhibits a faster burn rate due to its oxygenated nature. The combined effect of advanced auto-ignition and faster burn rate resulted in a steep rise in the in-cylinder pressures, leading to abnormal combustion above 20% load. Diluting the charge reduces reactivity and intake oxygen concentration, facilitating load extension.

This paper deals mainly with computer simulation of processes of Gasoline Direct Injection (GDI) associated with Extended Expansion Engine (EEE) concept applied to a four-stroke, single-cylinder SI engine. In the case of standard SI engines, part-load brake thermal efficiencies are low due to higher pumping losses. The pumping losses can be reduced by operating the engine always at full throttle as done in extended expansion engine. In extended expansion engine, higher Geometric Expansion Ratio (GER) compared to Effective Compression Ratio (ECR) is responsible for better performance at part loads. Usually, in this engine, by delaying inlet valve closure timing along with reduced clearance volume, extended expansion is achieved. Experimentally many researchers have proved that variable valve timing and variable compression ratio techniques adopted in SI engines, improves the part- load performance greatly.

Today, GDI engines are becoming very popular because of better fuel economy and low exhaust emissions. The gain in fuel economy in these engines is realized only in the stratified mode of operation. In wall-guided GDI engines, the mixture stratification is realized by properly shaping the combustion chamber. However, the level of mixture stratification varies significantly with engine operating conditions. In this study, an attempt has been made to understand the effect of engine operating parameters viz., compression ratio, engine speed and inlet air pressure on the level of mixture stratification in a four-stroke wall-guided GDI engine using CFD analysis. Three compression ratios of 10.5, 11.5 and 12.5, three engine speeds of 2000, 3000 and 4000 rev/min., and three inlet air pressures of 1, 1.2 and 1.4 bar are considered for the analysis. The CONVERGE software is used to perform the CFD analysis. Simulation is done for one full cycle of the engine.

Gasoline direct injection (GDI) engines are well known for their ability to operate at the stratified fuel-air mixture, and thereby they are highly efficient than port fuel injection (PFI) engines. However, the stratification of the in-cylinder mixture leads to higher nitrogen oxides (NOx) and soot emissions with lower hydrocarbon (HC) emissions. The PFI works under a homogeneous mixture, which leads to lower NOx and soot emissions with compensation of HC emissions. By combining the advantages of GDI and PFI modes, it is possible to achieve higher fuel efficiency with lower emissions. Therefore, in the present study, four different injection strategies, namely, pure GDI, gasoline-direct multiple-injection (GDMI), combined GDI with PFI (GDI-PFI), and pure PFI are investigated under various load conditions using computational fluid dynamics (CFD) analysis. The effect of these strategies on mixture formation, indicated mean effective pressure (IMEP), and emissions are evaluated.

Despite the advantages of turbocharging in improved engine performance and reduced exhaust emissions, commercial single-cylinder engines used for automotive applications remain naturally aspirated (NA) and are not generally turbocharged. This is due to the shortcomings with pulsated and intermittent exhaust gas flow into the turbine and the phase lag between the intake and exhaust stroke. In the present study, experimental investigations are initially carried out with a suitable turbocharger closely coupled to a single-cylinder diesel engine. Results indicated that the engine power dropped significantly by 40% for the turbocharged engine compared to the NA version even though the air mass flow rate was increased by at least 1.5 times with turbocharging. A novel approach of decoupling the turbine and the compressor and coupling them separately to the engine is proposed to address these limitations.

Single-cylinder engines in mass production are generally not turbocharged due to the pulsated and intermittent exhaust gas flow into the turbocharger and the phase lag between the intake and exhaust stroke. The present work proposes a novel approach of decoupling the turbine and the compressor and coupling them separately to the engine to address these limitations. An impulse turbine is chosen for this application to extract energy during the pulsated exhaust flow. Commercially available AVL BOOST software was used to estimate the overall engine performance improvement of the proposed novel approach compared to the base naturally aspirated (NA) engine. Two different impulse turbine layouts were analyzed, one without an exhaust plenum and the second layout having an exhaust plenum before the power turbine. The merits and limitations of both layouts are compared in the present study.

The distribution of fuel-air mixture inside the engine cylinder strongly influences the combustion process. Planar laser-induced fluorescence (PLIF) is commonly used for fuel distribution measurement, however, it is mostly reported on moderate- to large-sized engines. In the present work, PLIF is applied to measure the fuel distribution inside the cylinder of a small, four-stroke, port-fuel-injection (PFI), spark-ignition engine with displacement volume of 110 cm3. Iso-octane was used as the base fuel, and 3-pentanone (15% by volume) was added as a fluorescent tracer in the base fuel. The effect of equivalence ratio, considering ϕ = 1.2, 1.0, and 0.8, on in-cylinder fuel distribution was studied with low throttle opening of 25% at 1200 rpm. PLIF images were recorded at different crank angle degrees during both intake and compression strokes over a swirl measurement plane located at the TDC position.

Gasoline direct injection (GDI) engines are now trending in automobile field because of good fuel economy and low exhaust emissions over their port fuel injection (PFI) counter parts. They operate with a lean stratified mixture in most of conditions. However, their performance is dependent on mixture stratification which in-turn depends on fuel injection pressure, timing and strategy. But, the main challenge to GDI engines is soot and particulate matter (PM) emissions. However, they can be reduced by employing multi-stage fuel injection strategy. Therefore, in the present work, an effort has been made to study the effect of fuel injection parameters on soot emissions of a GDI engine using the CFD analysis. In addition, the study is also extended to evaluate the performance, combustion and other emission characteristics of the engine. First the engine is modelled using the PRO-E software. The geometrical details of the engine are obtained from the literature.

Small gasoline four stroke engines used in motorcycle applications run mostly at part load conditions. Here fuel economy and good drivability are the major requirements. In this work, a single cylinder, four stroke, 2 valve gasoline motorcycle engine in which part load performance needs to be improved was taken for investigation. Various factors affecting part load performance were investigated and it was found that high exhaust gas dilution was the cause of high cycle by cycle variations in this engine. Commercial software was used in order to predict exhaust gas dilution levels. Based on the simulation, a set of parameters that lead to low exhaust gas dilution were arrived at. These were implemented and tested on the engine and part load performance characteristics such as combustion stability, brake specific fuel consumption and torque output were found to be improved.

Mass-production single-cylinder engines are generally not turbocharged due to pulsated exhaust flow. Hence, about one-third of the fuel chemical energy is wasted in the engine exhaust. To extract the exhaust energy and boost the single-cylinder engines, a novel supercharging with a turbo-compounding strategy is proposed in the present work, wherein an impulse turbine extracts energy from the pulsated exhaust gas flow. Employing an impulse turbine for a vehicular application, especially on a single-cylinder engine, has never been commercially attempted. Hence, the design of the impulse turbine assumes higher importance. A nozzle, designed as a stator part of the impulse turbine and placed at the exhaust port to accelerate the flow velocity, was included as part of the layout in the present work. The layout was analyzed using the commercial software AVL BOOST. Different nozzle exit diameters were considered to analyze their effect on the exhaust back pressure and engine performance.

Adopting a low compression ratio (LCR) is a viable approach to meet the stringent emission regulations since it can simultaneously reduce the oxides of nitrogen (NOx) and particulate matter (PM) emissions. However, significant shortcomings with the LCR approach include higher unburned hydrocarbon (HC) and carbon monoxide (CO) emissions and fuel economy penalties. Further, poor combustion stability of LCR engines at cold ambient and part load conditions may worsen the transient emission characteristics, which are least explored in the literature. In the present work, the effects of implementing the low compression ratio (LCR) approach in a mass-production light-duty vehicle powered by a single-cylinder diesel engine are investigated with a major focus on transient emission characteristics.