Search Results

Setting the correct valve timing and lift based on the operating speed will be the key to achieving good volumetric efficiency and torque. Continuously variable valve timing systems are the best choice but are too expensive. In this work a novel two stage variable valve actuation system was conceived and developed for a small single cylinder three wheeler spark ignition engine. The constraints were space, cost and complexity. The developed system uses one cam for low speeds and another cam that has a higher lift and duration for high speeds. The shift between the cams occurs through the mechanism even as the engine runs by the operation of a stepper motor which can be connected to the engine controller. A one dimensional simulation model validated with experimental data was used to predict the suitable valve timings and lifts in low and high speed ranges. Two profiles were then selected.

This experimental study was aimed at improving a two-stroke S.I engine by injecting gasoline with air assistance through the cylinder barrel. Experimentally obtained performance and emission parameters of the engine at 25% and 100% throttle positions were analyzed at 3000 rpm. The timing of air assisted injection was optimized at 25% throttle and 3000 rpm. The performance and emissions of the engine were compared with those obtained with an optimized manifold injection system. In all cases the best spark timing was used. At 25% throttle although the thermal efficiency was increased only slightly, there was a significant reduction in HC emissions to 6.63 g/kW-h with cylinder barrel injection from 10.69 g/kW-h with manifold injection due to reduced short circuiting of the fuel. There was a reduction in NO emissions as well with cylinder barrel injection. Comparisons were made at the point of highest thermal efficiency at 100% throttle also.

Air motion inside the engine cylinder plays a predominant role on combustion and emission processes. An attempt has been made in this investigation to simulate the in-cylinder air motion in a DI diesel engine with four different piston configurations such as dome piston, bowl on dome and pentroof piston and pentroof offset bowl piston. For computational analysis, the commercial general purpose code STAR-CD Es-ice has been used, which works on the method of finite volume. To validate the simulation, qualitative and quantitative comparisons have been done with the PIV results available in the literature. From this study, the best possible piston configuration has been arrived at.

Direct injection diesel engines are used in both light duty and heavy duty vehicles because of higher thermal efficiency compared to SI engines. However, due to only short time available for fuel-air mixing, combustion process depends on proper mixing. As a result, DI Diesel engine emits more NOx and soot into the atmosphere. Therefore, to achieve better combustion with less emission and also to accelerate the fuel-air mixing to improve the combustion, appropriate design of combustion chamber is crucial. Hence, in this work a study has been carried out using CFD to evaluate the effect of combustion chamber configuration on Diesel combustion with two different piston bowls. The two different piston configurations considered in this study are centre bowl on flat piston and pentroof offset bowl piston.

This paper deals with experimental study of in-cylinder tumble flows in a single-cylinder, four-stroke, two-valve internal combustion engine using a pentroof-offset-bowl piston under non-reacting conditions with four intake manifold orientations at an engine speed of 1000 rev/min., during suction and compression strokes using particle image velocimetry. Two-dimensional in-cylinder tumble flow measurements and analysis are carried out in combustion space on a vertical plane passing through cylinder axis. Ensemble average velocity vectors are used to analyze the tumble flows. Tumble ratio (TR) and average turbulent kinetic energy (TKE) are evaluated and used to characterize the tumble flows. From analysis of results, it is found that at end of compression stroke, 90° intake manifold orientation shows an improvement in TR and TKE compared other intake manifold orientations considered.

Mixture distribution in the combustion chamber of gasoline direct injection (GDI) engines significantly affects combustion, performance and emission characteristics. The mixture distribution in the engine cylinder, in turn, depends on many parameters viz., fuel injector hole diameter and orientation, fuel injection pressure, the start of fuel injection, in-cylinder fluid dynamics etc. In these engines, the mixture distribution is broadly classified as homogeneous and stratified. However, with currently available engine parameters, it is difficult to objectively classify the type of mixture distribution. In this study, an attempt is made to objectively classify the mixture distribution in GDI engines using a parameter called the “stratification index”. The analysis is carried out on a four-stroke wall-guided GDI engine using computational fluid dynamics (CFD).

Preparation of air-fuel mixture and its stratification, plays the key role to determine the combustion and emission characteristics in a gasoline direct injection (GDI) engine working in stratified conditions. The mixture stratification is mainly influenced by the in-cylinder flow structure, which mainly relies upon engine geometry i.e. cylinder head, intake port configuration, piston profile etc. Hence in the present analysis, authors have attempted to comprehend the effect of cylinder head geometry on the mixture stratification, combustion and emission characteristics of a GDI engine. The computational fluid dynamics (CFD) analysis is carried out on a single-cylinder, naturally-aspirated four-stroke GDI engine having a pentroof shaped cylinder head. The analysis is carried out at four pentroof angles (PA) viz., 80 (base case), 140, 200 and 250 with the axis of the cylinder.

Ammonia is one of the most promising zero carbon fuels for meeting carbon neutrality targets and zero carbon emissions. Ammonia has gained a lot of research interest recently as a hydrogen energy carrier, and direct use of ammonia as a fuel in engines will aid the transformation toward sustainable energy future. In this work, the effect of ammonia shares on combustion and performance characteristics of methane-fueled SI engine is evaluated by increasing the ammonia share by small fractions (0 to 30% by volume) in the fuel mixture (CH4/NH3 blend). Experiments were performed at constant engine load of 8 Nm (BMEP of 1.52 bar), while maintaining constant engine speed (1500 rpm), stoichiometric operation (λ = 1), and optimum spark advance for MBT conditions.

This paper deals with in-cylinder flow field analysis in a motored two-stroke engine by CFD technique using STAR-CD. The main aim of this study is to find out the best turbulence model which predicts the fluid flow field inside the cylinder of a two-stroke engine. In this study, a single-cylinder, two-stroke engine which is very commonly used for two-wheeler application in India is considered. Entire analysis is done at an engine speed of 1500 rev/min. under motoring conditions. Here, three commonly used turbulence models viz. standard k-ε, Chen k-ε and RNG k-ε are considered. In addition, experiments were also conducted on the above engine at the motoring conditions to measure velocity vectors of in-cylinder flow fields using particle image velocimetry (PIV). The results of PIV were also used for validating the CFD predictions.

This paper deals with a numerical investigation on swirl generation by a helical intake port and its effects on in-cylinder flow characteristics with axisymmetric piston bowls in a small four-valve direct injection diesel engine. The novelty of this study is in determining the appropriate design and orientation of the helical port to generate high swirl. A commercial CFD software STAR-CD is used to perform the detailed three dimensional simulations. Preliminary studies were carried out at steady state conditions with the helical port which demonstrated a good swirl potential and the CFD predictions were found to have reasonably good agreement with the experimental data taken from literature. For transient cold flow simulations, the STAR-CD code was validated with Laser Doppler Velocimetry (LDV) experimental velocity components’ measurements available in literature.

Owing to a high power-to-weight ratio, mini internal combustion engine is used in propelling an unmanned air vehicle. In comparison to the performance characteristics, the investigations on the combustion aspects of mini engines are scanty. This investigation concerns study of the combustion process of a mini engine and its variability. For this purpose, the experimental cylinder pressure histories were obtained on a laboratory set-up of a 7.45 cm3 capacity mini engine. The analyses of experimental data at different throttle settings reveal that there existed a varied range of rich and lean misfiring limits around a reference equivalence ratio that corresponds to the respective maximum indicated mean effective pressure. At the limiting equivalence ratios, cylinder pressure measurements showed a high degree of cycle-to-cycle variations. In some cases, a slow combustion or misfiring event preceded a rapid combustion.

Despite the advantages of turbocharging in improved engine performance and reduced exhaust emissions, commercial single-cylinder engines used for automotive applications remain naturally aspirated (NA) and are not generally turbocharged. This is due to the shortcomings with pulsated and intermittent exhaust gas flow into the turbine and the phase lag between the intake and exhaust stroke. In the present study, experimental investigations are initially carried out with a suitable turbocharger closely coupled to a single-cylinder diesel engine. Results indicated that the engine power dropped significantly by 40% for the turbocharged engine compared to the NA version even though the air mass flow rate was increased by at least 1.5 times with turbocharging. A novel approach of decoupling the turbine and the compressor and coupling them separately to the engine is proposed to address these limitations.

Single-cylinder engines in mass production are generally not turbocharged due to the pulsated and intermittent exhaust gas flow into the turbocharger and the phase lag between the intake and exhaust stroke. The present work proposes a novel approach of decoupling the turbine and the compressor and coupling them separately to the engine to address these limitations. An impulse turbine is chosen for this application to extract energy during the pulsated exhaust flow. Commercially available AVL BOOST software was used to estimate the overall engine performance improvement of the proposed novel approach compared to the base naturally aspirated (NA) engine. Two different impulse turbine layouts were analyzed, one without an exhaust plenum and the second layout having an exhaust plenum before the power turbine. The merits and limitations of both layouts are compared in the present study.

The distribution of fuel-air mixture inside the engine cylinder strongly influences the combustion process. Planar laser-induced fluorescence (PLIF) is commonly used for fuel distribution measurement, however, it is mostly reported on moderate- to large-sized engines. In the present work, PLIF is applied to measure the fuel distribution inside the cylinder of a small, four-stroke, port-fuel-injection (PFI), spark-ignition engine with displacement volume of 110 cm3. Iso-octane was used as the base fuel, and 3-pentanone (15% by volume) was added as a fluorescent tracer in the base fuel. The effect of equivalence ratio, considering ϕ = 1.2, 1.0, and 0.8, on in-cylinder fuel distribution was studied with low throttle opening of 25% at 1200 rpm. PLIF images were recorded at different crank angle degrees during both intake and compression strokes over a swirl measurement plane located at the TDC position.

For more than a decade there is a progressive demand for fuel efficient and high specific power output engines. Optimization of engine cooling and thermal management is one of the important activities in engine design and development. In the present paper an effort has been made to simulate the heat transfer modes of cylinder block and head for a present 4-stroke air-cooled motorcycle engine. Two and three-dimensional decoupled and conjugate heat transfer analysis has been done with commercially available computational fluid dynamics (CFD) codes. Experimental results are also presented. A complete simulation model has been developed and CFD techniques have been applied to design and optimize air cooling surfaces of cylinder head and block, for an air cooled motorcycle engine. The two dimensional analysis is an easy and fast method to predict fin surface temperature, heat transfer co-efficient and flow velocity.

Mass-production single-cylinder engines are generally not turbocharged due to pulsated exhaust flow. Hence, about one-third of the fuel chemical energy is wasted in the engine exhaust. To extract the exhaust energy and boost the single-cylinder engines, a novel supercharging with a turbo-compounding strategy is proposed in the present work, wherein an impulse turbine extracts energy from the pulsated exhaust gas flow. Employing an impulse turbine for a vehicular application, especially on a single-cylinder engine, has never been commercially attempted. Hence, the design of the impulse turbine assumes higher importance. A nozzle, designed as a stator part of the impulse turbine and placed at the exhaust port to accelerate the flow velocity, was included as part of the layout in the present work. The layout was analyzed using the commercial software AVL BOOST. Different nozzle exit diameters were considered to analyze their effect on the exhaust back pressure and engine performance.