Search Results

In order to meet current and future emission and CO2 targets, an efficient vehicle thermal management system is one of the key factors in conventional as well as in electrified powertrains. Global vehicle simulation is already a well-established tool to support the vehicle development process. In contrast to conventional vehicles, electrified powertrains offer an additional challenge to the thermal conditioning: the durability of E-components is not only influenced by temperature peaks but also by the duration and amplitude of temperature swings as well as temperature gradients within the components during their lifetime. Keeping all components always at the preferred lowest temperature level to avoid ageing under any conditions (driving, parking, etc.) will result in very high energy consumption which is in contradiction to the efficiency targets.

With the advent of PHEV vehicles OEMs face additional NVH issues. A particularly new issue is a low frequency booming noise caused during charging of batteries using the internal combustion engine. During charging the engine is operated at low rotational speeds and high loads, leading to pronounced low frequency noise. While in the past reducing low frequency noise either required large absorbers and/or heavy dampers, today the issue can be tackled by use of an Active Noise Cancellation system. Jaguar Land Rover decided to introduce an Active Noise Cancellation system in the PHEV variants of some of their vehicles. The system builds upon software by Müller-BBM Active Sound Technology GmbH and makes use of the existing audio amplifiers. The only extra hardware component required are microphones in the vehicle headliner.

Approaching engineering limits for the thermal design of battery modules requires virtual prototyping and appropriate models with respect to physical depth and computational effort. A multi-scale and multi-domain model describes the electrochemical behavior of a single battery unit cell in 1D+1D at the level of intra-cell phenomena, and it applies a 3D thermal model at module level. Both models are connected within a common vehicle simulation platform. The models are discussed with special emphasis on battery degradation such as solid electrolyte interphase layer formation, decomposition and lithium plating. The performance of the electrochemical model is assessed by discharge cycles and repeated charge/discharge simulations. The thermal module model is compared to CFD reference data and studied with respect to its grid sensitivity.

The present work introduces an innovative mechanistically based 0D spray model which is coupled to a combustion model on the basis of an advanced mixture controlled combustion approach. The model calculates the rate of heat release based on the injection rate profile and the in-cylinder state. The air/fuel distribution in the spray is predicted based on momentum conservation by applying first principles. On the basis of the 2-zone cylinder framework, NOx emissions are calculated by the Zeldovich mechanism. The combustion and emission models are calibrated and validated with a series of dedicated test bed data specifically revealing its capability of describing the impact of variations of EGR, injection timing, and injection pressure. A model based optimization is carried out, aiming at an optimum trade-off between fuel consumption and engine-out emissions. The findings serve to estimate an economic optimum point in the NOx/BSFC trade-off.

The present work introduces a fully integrated real-time (RT) capable engine and vehicle model. The gas path and drive line are described in the time domain of seconds whereas the reciprocating characteristics of an IC engine are reflected by a crank angle resolved cylinder model. The RT engine model is derived from a high fidelity 1D cycle simulation and gas exchange model to support an efficient and consistent transfer of model data like geometries, heat transfer or combustion. The workflow of model calibration and application is outlined and base ECU functionalities for boost pressure, EGR, smoke and idle speed control are applied for transient engine operation. Steady state results of the RT engine model are compared to experimental data and 1D high fidelity simulations for 19 different engine load points. In addition an NEDC (New European Drive Cycle) is simulated and results are evaluated with data from chassis dynamometer measurements.

In a tiered cooling pack, the airflow through the individual heat exchangers is determined by the package and aperture lay out. Each heat exchanger rejects heat as a function of the internal coolant flows, the cooling airflow and the air temperature. In a typical automotive cooling pack, the cooling airflow will be non-uniform in velocity and temperature due to fans, aperture geometry, exterior flows, heat exchangers and recirculation. In a drive cycle, these boundary conditions will change with vehicle operating conditions like vehicle speed, engine speed, ambient temperature, and altitude. These non-uniform conditions on the cooling pack can lead to significant errors when uniform boundary conditions are assumed in a transient simulation. This error is commonly corrected using vehicle test data. A predictive approach, which eliminates the need for correlation vehicle testing, is presented.

Paper outlines a case study on optimal control of a brushless direct-current (BLDC) motor, operating as an Integrated Starter Generator (ISG) in a micro hybrid propulsion system for motorcycles. Main research focus is optimization of BLDC machine torque characteristics, particularly in starter operation mode, in order to improve cranking of the internal combustion engine (ICE) at various operation conditions. Stringent cranking torque demands, limited physical dimensions of the electrical machine and a wide rotational speed range of prototype ICE are most challenging reasons for the exhaustive study of applicable control algorithms in the low rpm range. Two approaches for optimization of torque characteristics are discussed, common known flux-weakening method and the modification of power-switch conduction angle, respectively. The evaluation of most relevant control approaches is based on computer simulation and prototype set-up measurements.

To reduce carbon emissions and mitigate traffic congestion in urban environments, new innovative transportation concepts are required. While public transportation covers certain segments, it cannot supply all possible routes, use cases, and preferences and hence, other solutions are needed as well. Urban drive missions are not typically calling for huge powers or even large energy capacities. In the vehicle design, this should be shown as rightsizing. It is not only the powertrain that should be rightsized but also the vehicle physical dimensions, to enable, e.g., convenient maneuvering. Furthermore, due to the variety of options (walking, biking, scooters, public transportation etc.), one might need a personal vehicle only occasionally, and therefore, a vehicle with shared and multipurpose capabilities would be an asset. Lastly, since small urban vehicles are considered unsafe, improving the safety and general confidence on small vehicles is vital for the market penetration.