Search Results

Advanced compression ignition combustion system which reduces simultaneously both nitride oxides (NOx) and particulate matter (PM) is a promising approach to meet future emission regulations. In order to achieve advanced compression ignition, flexible fuel injection is required for ultra-early and post-TDC injections, which conventional injector fails to accomplish due to wall-wetting effect. In this work, special injectors with the spray angle of 60 degree are applied on a 4 cylinder mass-production diesel engine without modification of the engine configuration. For application-oriented study, sweep experiments of injection timings and durations, fuel injection pressure and the boost pressure are carried out to investigate the relationships between the control parameters and the engine performance. Model based calibration and real application tests validate the maximum applicable operation range of maximum speed of 2200 RPM and IMEP of 8.0 bar.

Due to the potential on decreasing fuel consumption and design flexibility, parallel configurations are widely used for hybrid electric vehicles (HEVs). However, the fuel economy and economic profitability of parallel HEVs for heavy-duty truck applications under Chinese driving conditions still need to be investigated. It is uneasy to improve the fuel economy of parallel HEVs with a single electric motor from control perspective only. In this article, the battery size of the architecture is optimized by using the dynamic programming (DP) approach, based on a dynamic degradation model of the LiFePO4 battery. Moreover, based on the DP results, a near-optimal control strategy of the hybrid powertrain system for online application is proposed. Finally, with two economic assumptions, the initial costs, operation costs, and payback periods are obtained in a total cost of ownership framework perspective.

In low-temperature environment, heat supply requires considerable energy, which significantly increases energy consumption and shortens the mileage of electric vehicle. In the fuel cell vehicles, waste heat generated by the fuel cell system can supply heat for vehicle. In this paper, a thermal management system is designed for a the fuel cell interurban bus. Thermal management strategy aiming at temperature regulation for the fuel cell stack and the passenger compartment and minimal energy consumption is proposed. System model is developed and simulated based on AMESim and Matlab/Simulink co-simulation. Simulation results show that the fuel cell system can provide about 78 % energy of maximum heat requirement in -20 °C ambient temperature environment.

Power-split configuration is highlighted as the most popular concept for full hybrid electric vehicles (HEV). However, the energy management and design of power-split heavy duty truck under Chinese driving conditions still need to be investigated. In this paper, the parametric design, a rule-based control strategy and an equivalent consumption minimization strategy (ECMS) for the power-split heavy duty truck are presented. Besides, the influence of a penalty factor also discussed under ECMS algorithm. Meanwhile, two different methods to search the engine operation point have been proposed and the reason of different economy performance is presented by using energy flow chart. And the simulation results show both fuel consumption can satisfy the second phase fuel consumption standard and the third phase fuel consumption standard which will be implemented in 2020, under C-WTVC (Chinese-World Transient Vehicle Cycle).

This paper conducts an investigation on the operating cycle of Bus No. 306, which is equipped with wireless charging system, in Changsha, Hunan Province, China. The wireless charging system and electric buses are manufactured by ZTE Corporation (Zhongxing Telecommunication Equipment Corporation) and BYD Company Limited, respectively. In this paper, the operating cycle is quantified and modeled based on experimental data. The real-time bus route and SOC (state of charge) during daytime operation are recorded with the help of GPS (global position system) and BMS (battery management system). The wireless charging process is tested with a power analyzer and its charging efficiency is compared with a plug-in system. Besides, the radiation level while charging is also taken into consideration. Currently, the buses are designed to operate in daytime and get charged at night.

Energy saving is becoming one of the most important issues for the next generation of commercial vehicles. The fuel consumption limits for commercial vehicles in China have stepped into the third stage, which is a great challenge for heavy duty commercial vehicles. Hybrid technology provides a promising method to solve this problem, of which the dual motor coaxial series parallel configuration is one of the best options. Compared with parallel configuration, the powertrain can not only operate in pure electric or parallel mode, but also can operate in series mode, which shows better flexibility. In this paper, regulations on test cycle, fuel consumption limits and calculation method of the third stage will be introduced in detail. Then, the quasi-static models of the coaxial series parallel powertrain with/without gearbox under C-WTVC (China worldwide transient vehicle cycle) are built. The control strategies are designed based on engine and motor performance.

Low temperature combustion (LTC) is an advanced combustion mode, which can achieve low emissions of NOx and PM simultaneously, and keep relatively high thermal efficiency at the same time. However, one of the major challenges for LTC is the cold condition. In cold conditions, stable compression ignition is hard to realize, while thermal efficiency and emissions deteriorate, especially for gasoline or fuel with high octane number. This study presents using pressure sensor glow plugs (PSG) to realize Glow plug assisted compression ignition (GA-CI) at cold conditions. Further, a glow plug control unit (GPCU) is developed, a closed-loop power feedback control algorithm is introduced based on GPCU. In the experiment, engine coolant temperature is swept. Experimental results show that GA-CI has earlier combustion phases, larger combustion duration and higher in-cylinder pressure. And misfire is avoided, cycle-to-cycle variations are greatly reduced.

This study investigates the performance of a diesel engine fueled with naphtha under different load by varying injection parameters and exhaust gas recirculation (EGR) rate. The experiments were conducted on a 1.9-liter common rail diesel engine with a compression ratio of 17.5. Naphtha with a research octane number of 60.5 was tested. Three multi-injection strategies were designed. Each injection strategy, aided with EGR, conducts a characteristic combustion mode. Multi-injection strategies and single-injection strategy were tested and compared at one operating point under different main injection timing and EGR conditions. Results indicate that the well-designed multi-injection strategy has advantages over the single injection strategy in lowering noise, emissions and improving combustion efficiency. Among the three strategies, the strategy with 15-degree pilot timing and 2mg/cycle pilot injection could achieve both low NOx and PM emissions without sacrificing much fuel efficiency.

The lithium-ion battery plays an important role in saving energy and lowering emissions. Many parameters like temperature have an influence on the characteristic of the battery and this phenomenon becomes more serious in an electric vehicle. In this paper, the application of a boost DC/DC converter to the battery system of high power for online AC impedance identification is proposed. The function of the converter is to inject a current excitation signal into the battery at work and the normal output current is drawn by a load. Through analyzing the average state space equations and deriving the small signal model of the converter, the gain function is deduced of the fluctuated current signal against the fluctuated duty cycle which controls the converter. The control algorithm is designed and the system model is verified using Matlab/Simulink with respect to the disturbance current signal generation, the gain function and its variation with frequency range.

An imperceptible engine start is critical to the acceptance of hybrid vehicles. This paper focusses on an optimal control problem that tries to reduce vibration during engine start. Efforts are made to obtain the optimal speed trajectory that could cause minimum vibration during engine start. In the first section, the target diesel powertrain is introduced. A four cylinder diesel engine is coaxially paralleled with an ISG motor. The ISG motor serves as the engine starter and engine flywheel. Its dynamic model is established using crank-link dynamics. Secondly, an index is brought out to evaluate the severity of vibration. The cylinder pressure variation is the main cause of engine torque ripple, which in turn results in engine speed fluctuation. The square of the angular acceleration is chosen as the index of vibration. The index shows a positive relation of cylinder pressure in terms of amplitude.

Electric vehicle (EV) is a worldwide researching focus due to its environmental friendliness, but the inaccurate Remaining Driving Range (RDR) estimation hinders the EVs' popularity, and an accurate determination of the battery Residual Usable Energy (RUE) is the key factor to obtain a precise RDR value. A common RUE estimation method is based on State-of-Charge (SOC) estimation, in which the RUE is proportionally related to the current SOC. However, the battery voltage varies significantly under real-world conditions, and the traditional method results in certain estimation errors. An adaptive RUE prediction method (AEP) is introduced in this paper, in which the dynamic voltage is predicted based on the future discharge profile and a battery model, while the RUE is then calculated by the predicted voltage and current sequences.

In order to reduce driver's anxiety about range and energy, a direct and effective approach is to offer the remaining driving range based on the vehicle's states. Consequently, the estimation accuracy of the battery's remaining energy is very important. This paper introduces a experiment-based model for predicting the remaining energy, which considers many factors, such as current, temperature, difference between battery cells, and so on. This approach ensures the accuracy of the remaining driving range. Finally the method is validated through the environment space test. Validation results show that this method can offer exact remaining energy, which reduces the estimation error of the remaining range greatly.

Engine torque fluctuation is a great threat to vehicle comfort and durability. Former researches tried to solve this problem by introducing active damping system, which means the motor is controlled to produce torque ripple with just the opposite phase to that of the engine. By this means, the torque fluctuation produced by the motor and the engine can be reduced. In this paper, a new method is raised. An attempt is proposed by changing the traditional structure of the motor, making it produce ripple torque by itself instead of controlling the motor. In this way a special used ISG (Integrated Starter Generator) motor for HEV (Hybrid Electrical Vehicles) is made to achieve active damping. In order to study the possibility, a simulation, which focus on the motor instead of the whole system, is developed and series-parallel configuration is used in this simulation. As for the motor that used in this paper, four kinds of motors have been investigated and compared.

This paper presents an investigation of drivability issue of engine start-stop. Hybrid vehicles provide excellent benefits regarding fuel efficiency and emission. However, vibration results from constant engine start and stop events generate drivability issues, thus compromising driving comfort. This paper has designed a high speed torque sensor to capture instantaneous torque at the engine shaft. Its consequences help to find out the most suitable index of vibration severity. This paper is organized in four sections. The first section introduces the powertrain to be studied. The second section introduces development of a specially designed torque sensor. The torque sensor is installed between the engine and ISG (Integrated Starter Generator), alongside with an encoder. The torque sensor is utilized to collect the instantaneous shaft torque on occasion of engine start. In the third section, this paper has performed two experiments.