Search Results

This paper presents an experimental study of the emission characteristics of a small Spark-Ignited, LPG engine. A single cylinder, four-stroke, water-cooled, 125cc SI engine for motorcycle is modified for using LPG fuel. The power output of LPG is above 95% power output of gasoline. The emission characteristics of LPG are compared with the gasoline. The test result shows that LPG for small SI engine will help to reduce the emission level of motorcycles. The HC and CO emission level can be reduced greatly, but NOx emissions are increased. The emission of motorcycle using LPG shows the potential to meet the more strict regulation.

The purpose of this study is to investigate the possibility of acetone-butanol-ethanol (ABE) blended with diesel without further component recovery which has high costs blocking the industrial-scale production of bio-butanol. The combustion characteristics of ABE and diesel blends were studied in a constant volume chamber. In this study, 50% and 80% vol. ABE (without water) were mixed with diesel and the vol. % of acetone, butanol and ethanol were kept at 30%, 60% and 10% respectively. The in-cylinder pressure was recorded using a pressure transducer and the time-resolved natural luminosity was captured by high speed imaging. Combustion visualization using laser diagnostics would provide crucial fundamental information of the fuel's combustion characteristics. With the different percentage of the ABE blended in the diesel, the soot oxidation, the ignition delay and the soot lift-off length were studied in this work.

Dual loop EGR systems (having both a high pressure loop EGR and a low pressure loop EGR) have been successfully applied to multiple light-duty diesel engines to meet Tier 2 Bin 5 and Euro 5/6 emissions regulations [1, 2], including the 2009 model year VW Jetta 2.0TDI. Hyundai and Toyota also published their studies with dual loop EGR systems [3, 4]. More interest exists on the low pressure loop EGR effects on medium to heavy duty applications [5]. Since the duty cycles of light duty diesel and heavy duty diesel applications are very different, how to apply the dual loop EGR systems to heavy duty applications and understanding their limitations are less documented and published. As a specific type of heavy duty application, this paper studied the dual loop EGR effects on the retrofit applications of heavy duty diesel for delivery and drayage applications. The reduction of NOx emissions and the impact on fuel economy and controls are discussed.

Three thermo-wires with amplifying circuits have been developed to measure the time-resolved concentration of the exhaust gas recirculated into the intake manifold by a rotary valve-based exhaust gas recirculation (EGR) system of a diesel engine. Good agreement was found between the EGR rates measured by the temperature based system and a conventional CO2 tracing system. The developed EGR measuring system was used to investigate the EGR transient response in a turbo-charged and after-cooled diesel engine with a real-time measure and control system. The EGR response under EGR valve step change and engine transient operating conditions are discussed. At first, the engine was running under a certain steady condition with zero recirculated exhaust gas, then the rotary valve opened to maximum within 0.1s to demonstrate the EGR step change behavior. EGR rate and air intake stabilized in 0.5s.

For diesel/natural gas dual fuel engines, the combustion of pilot diesel injection plays an important role to subsequent mixture combustion process. To better understand the effects of multiple injections, a detailed study was conducted on a 6-cylinder turbocharged intercooler diesel/natural gas dual fuel heavy-duty engine at low loads. Multiple variables were tested, including the single injection timings, the multiple injections timings and the mass ratios. The investigated results showed that the multiple pilot diesel injections have an obvious effect on not only pilot diesel combustion process but also natural gas mixture combustion process. Early injection leads to a pilot-diesel-ignition-mode and it is a two-stage auto ignition mode. This mode differs from the compression ignition mode of traditional diesel engine in regard to its random occurrence location within the spray.

In this study, an experimental investigation was conducted using a direct injection single-cylinder diesel engine equipped with a test common rail fuel injection system to clarify how dimethyl ether (DME) injection characteristics affect the heat release and exhaust emissions. For that purpose the common rail fuel injection system (injection pressure: 15 MPa) and injection nozzle (0.55 × 5-holes, 0.70 × 3-holes, same total holes area) have been used for the test. First, to characterize the effect of DME physical properties on the macroscopic spray behavior: injection quantity, injection rate, penetration, cone angle, volume were measured using high-pressure injection chamber (pressure: 4MPa). In order to clarify effects of the injection process on HC, CO, and NOx emissions, as well as the rate of heat release were investigated by single-cylinder engine test. The effects of the injection rate and swirl ratio on exhaust emissions and heat release were also investigated.

This study investigates the fundamental stiffness and damping properties of a self-damped pneumatic suspension system, based on both the experimental and analytical analyses. The pneumatic suspension system consists of a pneumatic cylinder and an accumulator that are connected by an orifice, where damping is realized by the gas flow resistance through the orifice. The nonlinear suspension system model is derived and also linearized for facilitating the properties characterization. An experimental setup is also developed for validating both the formulated nonlinear and linearized models. The comparisons between the measured data and simulation results demonstrate the validity of the models under the operating conditions considered. Two suspension property measures, namely equivalent stiffness coefficient and loss factor, are further formulated.

A novel non-destroy repeatable-use impact theory based total cylinder sampling system has been established. This system is mainly composed of a knocking body and a sampling valve. The knocking body impacts the sampling valve with certain velocity resulting in huge force to open the sampling valve and most of the in-cylinder gas has been dumped to one sampling bag for after-treatment. The feasibility and sampling response characteristics of this impact theory based total cylinder sampling system were investigated by engine bench testing. Within 0 to 35°CA ATDC (Crank Angle After Top Dead Center) sample timing 50 percent to 80 percent of in-cylinder mass would be sampled, which was a little less compared with the traditional system. The half decay period of pressure drop was 10 to 20 degrees crank angle within 0 to 60°CA ATDC sample timing, which was about 2-3 times of the traditional system.

The incomplete combustion and misfire of diesel engine during starting result in unwanted white smoke. The histories of combustion and emission in different phases under different start conditions were studied in this paper. The optimization of the fuel injection control strategy under start conditions was performed. When the diesel engine is started under low temperature, the control strategy adapted to start the engine with a certain constant fuel mass injected per cycle, there may be misfire cycles in the initial period or in the transitional process, which is mainly caused by the mismatch between the fuel mass injected per cycle and the instantaneous engine speed. Therefore, an optimized control strategy was put forward, namely, the engine starts with high fuel mass injection in the first several cycles and then decreases step by step during the transitional period until it operates at idle condition. This strategy was validated to decrease significantly the misfire cycles.

This paper presents an investigation of cold starts based on a cycle-by-cycle control strategy in an LPG EFI engine. Experiments were carried out in a four-stroke, water-cooled, single cylinder, 125cc SI engine with an EFI system. Effects of the first injection pulse width and the first combustion cycle on the characteristics of the cold-start were analyzed based on the histories of transient engine speeds and cylinder pressures. The study focuses on how to realize the controllable ignition cycle and the single-cycle and multi-cycle combustions were tested based on the single starting injection pulse width. Test results show that the first combustion cycle has an important effect on HC emission and combustion stability of following cycles at cold-start. The injection pulse width is the key factor determining the characteristics of an ignition cycle during the cold-start.

In order to improve the performance of low temperature combustion of diesel engines to achieve ultra-low emissions and load condition expansions, exhaust gas recirculation (EGR) stratification in the cylinder was proposed to further intensify local EGR concentration and reduce the amount of EGR to acquire high average oxygen concentration within cylinder. In this study, the intake/exhaust port and combustion chamber models were explored by CFD software on a four-valve HD diesel engine, and fresh air and EGR respectively replaced by O2 and CO2 were introduced with division and timing intake strategies during the intake process for stratification optimization.

The purpose of this study is to evaluate the impact of two-stage pilot injection parameters on the combustion and emissions of pilot diesel compression ignition natural gas (CING) engine at low load. Experiments were performed using a diesel/natural gas dual-fuel engine, which was modified from a six-cylinder diesel engine. The effect of injection timing and injection pressure of two-stage pilot diesel were analyzed in order to reduce both the fuel consumption and total hydrocarbon (HC) and carbon monoxide (CO) emissions under low load conditions. The results indicate that, because injection timing can determine the degree of pilot diesel stratification, in-cylinder thermodynamic state, and the available mixing time prior to the combustion, the combustion process can be controlled and optimized through adjusting injection timing.

Based on the research and analysis of the current brake systems, this paper presents a novel electro-hydraulic brake system, which can better meet the functional requirements. The system mainly contains a master cylinder, two brake hydraulic cylinders and drive motors, two transmission mechanisms, thirteen solenoid valves, pedal force simulator, etc. Since the proposed brake system uses a dual motor along with two brake hydraulic cylinders, it has advantages in providing fast pressure response, flexible working modes, high precision and strong fault tolerance. In order to facilitate the study of pressure control algorithm for the proposed brake system, a mathematical model of the brake system is firstly established, then a multiplexed time-division pressure control algorithm is proposed to realize the simultaneous or partially simultaneous pressure control, which ensures the high precision and short response time.

A very competitive alcohol for use in diesel engines is butanol. Butanol is of particular interest as a renewable bio-fuel, as it is less hydrophilic and it possesses higher heating value, higher cetane number, lower vapor pressure, and higher miscibility than ethanol or methanol. These properties make butanol preferable to ethanol or methanol for blending with conventional diesel or gasoline fuel. In this paper, the spray and combustion characteristics of pure n-butanol fuel was experimentally investigated in a constant volume combustion chamber. The ambient temperatures were set to 1000 K, and three different oxygen concentrations were set to 21%, 16%, and 10.5%. The results indicate that the penetration length reduces with the increase of ambient oxygen concentration. The combustion pressure and heat release rate demonstrate the auto-ignition delay becomes longer with decreasing of oxygen concentrations.

During the vehicle braking, the Regenerative braking system (RBS) transforms the kinetic energy into electric power, storing it in the power sources. To secure the baking process, it is required to use hydraulic braking pressure to coordinately compensate the regenerative braking pressure. The traditional hydraulic pressure control algorithm which is used in regenerative braking system coordinated control has obvious laddering effect in braking. Unit control cycle pressure deviations seriously affect the comfort and the braking feeling on the vehicle.

In the internal combustion engine (ICE), about 40% of fuel energy is released into the atmosphere through waste gas. To recovery the energy, the Organic Rankine Cycle (ORC) has been widely used, and lots of previous studies have selected the rotating turbine as the expander of ORC. However, the rotating turbine has disadvantages of high manufacturing cost and narrow applicable range. For the above reasons, a free piston with constant force output which functions as expander in ORC is proposed to recover the waste energy of exhaust gas from internal combustion engine (ICE). In the system, the free piston with constant force output operates reciprocally to output work under the driving of working fluid R245ca, which absorbs heat from waste gas and provides vapor power.