Search Results

This paper examines the conformability of elastic piston rings to a distorted cylinder bore. Several bounds are available in the literature to help estimate the maximum allowable Fourier coefficient in a Fourier expansion of bore distortion: the analytically derived bounds in [7] and [8], and the semi-empirically derived bounds discussed in [9]. The underlying assumptions for each set of analytic bounds are examined and a multiple order algorithm is derived. The proposed algorithm takes account of multiple orders of distortion at once. It is tested with finite element (FE) data and compared to the classical bound approach. The results indicate that the bounds in [7] are compatible with linear elasticity theory (LET), whereas the bounds in [8] are not. Furthermore, numerical evidence indicates that the present multiple order algorithm can predict seal breaches more accurately than either of the other analytic bounds.

The research shows the experimental results for a free piston linear engine according to operation conditions of the linear engine and the structure of linear generator for generating electric power. The powerpack used in this paper consists of the two-stroke free piston linear engine, linear generators and air compressors. Each parameter of fuel input heat, equivalence ratio, spark timing delay, electrical resistance and air gap length were set up to identify the combustion characteristics and to examine the performance of linear engine. The linear engine was fueled with propane. In the course of all linear engine operations, intake air was inputted under the wide open throttle state. Air and fuel mass flow rate were varied by using mass flow controller and these were premixed by pre-mixing device. Subsequently, pre-mixture was directly supplied into each cylinder.

This research investigated the mechanism of the effects of hydraulic dampers, which are attached to vehicle body structures and are known by experience to suppress vehicle body vibration and enhance ride comfort and steering stability. In investigating the mechanism, we employed quantitative data from riding tests, and analytical data from simplified vibration models. In our assessment of ride comfort in riding tests using vehicles equipped with hydraulic dampers, we confirmed effects reducing body floor vibration in the low-frequency range. We also confirmed vibration reduction in unsprung suspension parts to be a notable mechanical characteristic which merits close attention in all cases. To investigate the mechanism of the vibration reduction effect in unsprung parts, we considered a simplified vibration model, in which the engine and unsprung parts, which are rigid, are linked to the vehicle body, which is an elastic body equipped with hydraulic dampers.

While there has been an empirical rule telling suspension designers that a slight rearward inclination of the wheel travel locus could improve ride harshness performance, there has not been any quantitative proof on it, to the extent of authors' knowledge. The authors planned to analyze the phenomenon by quantitatively measuring the force transmission via suspension, to find out that the amplitude of longitudinal force transmission to the sprung mass changes significantly depending on the above inclination angle. Further investigation has lead to a conclusion that the force transmission from ground to tire has a sharp directivity. And that the relationship between this direction and the direction of wheel travel is a dominant factor, which decides the magnitude of longitudinal force transmission to the sprung mass. In order to make use of the finding, the optimal wheel center locus inclination in side view has been studied, to minimize the longitudinal force transmission.

The popularity of AWD passenger vehicles presents a challenge to provide car-like drive-train NVH within a relatively small package space. This paper describes a drive-train NVH case study in which analysis and test were used, in conjunction, to solve an NVH problem. Also, it details a systematic process of using the analytical model to identify and resolve similar problems. The particular problem for this case study is a noise and vibration issue occurring at 75 MPH primarily in the middle seat of an all-wheel drive vehicle. Tests indicated that it may be due to propeller shaft imbalance. Analysis results showed good correlation with the tests for that loading condition. Several solutions were identified, which were confirmed by both test and analysis. The most cost-effective of these solutions was implemented.

Operational analysis of automotive engines using flexible multi-body dynamics is increasingly important from the viewpoint of multi-objective optimization as it can predict not only vibration, but also stress and friction at the same time. Still, the finite element (FE) models used in this analysis have large degrees-of-freedom, so iterative calculation takes a lot of time when there is form change. This research therefore describes a technique that applies a modal differential substructure method (a technique that reduces the degrees of freedom in a FE model) that can simulate form changes in FE models by changing modal mass and modal stiffness in reduced models. By using this method, non-parametric form change in FE model can be parametrically simulated, so it is possible to speed up repeated vibration calculations. In the proposed method, FE model is finely divided for each form change design area, and a reduced model of that divided structure is created.

A dual piston Variable Compression Ratio (VCR) engine has been newly developed. This compact VCR system uses the inertia force and hydraulic pressure accompanying the reciprocating motion of the piston to raise and lower the outer piston and switches the compression ratio in two stages. For the torque characteristic enhancement and the knocking prevention when the compression ratio is being switched, it is necessary to carry out engine controls based on accurate compression ratio judgment. In order to accurately judge compression ratio switching timing, a control system employing the Hidden Markov Model (HMM) was used to analyze vibration generated during the compression ratio switching. Also, in order to realize smooth torque characteristics, an ignition timing control system that separately controls each cylinder and simultaneously performs knocking control was constructed.

A significant drawback to HCCI engines is the knocking caused by rapid increases in pressure. Such knocking limits the capacity for high-load operation. To solve this problem, thermal stratification in the combustion chamber has been suggested as possible solution. Thermal stratification has the potential to reduce the maximum value of the rate of pressure increase combustion by affecting the local combustion start time and extending the duration of combustion. The purpose of this study was to experimentally obtain fundamental knowledge about the effect of thermal stratification on the HCCI combustion process. Experiments were conducted in a rapid compression machine (RCM) equipped with a quartz window to provide optical access to the combustion chamber. The machine was fueled with DME, n-Butane, n-Heptane and iso-Octane, all of which are currently being investigated as alternative fuels and have different low temperature characteristics.

When the belt contacts a pulley in a pushing belt-type CVT, vibration is generated by frictional force due to rubbing between the individual elements that are components of the belt, which is said to increase wear and noise. The authors speculated that the source of that vibration is misalignment of the secondary pulley and primary pulley V-surfaces. To verify that phenomenon, a newly developed micro data logger was attached to an element of a mass-produced metal pushing V-belt CVT and the acceleration was measured at rotations equal to those at drive (1000 to 2500 r/m). In addition, the results of calculations using a behavior analysis model showed that changes in pulley misalignment influence element vibration, and that the magnitude of the vibration is correlated to the change in the metal pushing V-belt alignment immediately before the element contacts the pulley.

In engines having an inline four cylinder DOHC configuration, the rotational vibrations of camshaft increase at high engine speeds above 10000 rpm, causing an increase of tension in the cam chain. It is therefore difficult to realize an optimum designing of a cam chain system when the durability has to be taken into considerations. Using the simulation we analyzed in this research how the rotational vibrations and tension increase at high engine speeds in an inline four cylinder DOHC engine. As its consequent, it is understood that the increases of rotational vibrations and tension caused by the resonance of the spring mass vibration system in which the cam chain serves as springs and the camshafts as the equivalent masses. Also it is found out that the vibration system is of a unique non-linear type in which the resonance of the fourth order frequency is also excited by the crankshaft torque fluctuations of the second order frequency.

Regarding the solution for various issues on engine tribology, in order to understand the involvement of temperature in the friction and scuffing under the mixed and/or boundary lubrication regime, the two cases of piston ring & cylinder liner and cam & tappet were analytically studied. The friction between sliding interfaces is composed of four shear stresses from the viscous oil-films, the adsorbed oil molecules, the tribofilms due to oil additives, and the true metal contacts on surface asperities. Since all the shear stress have exponential temperature dependences, the relationship between the frictional shear stress and temperature is assumed to be expressed by the Arrhenius equation. Through analyzing friction data measured in laboratory tests conducted under the same temperature and sliding conditions as during the break-in of engines, various levels of temperature involvement were clarified.

This paper summarizes the development of a predictive vibro-acoustic full vehicle model of a mid-size sedan and focuses on the engineering analysis procedures used to evaluate the design performance related to engine induced noise and vibration. The vehicle model is build up from a mixture of test-based and finite element component models. FRF Based Substructuring is used for their assembly. The virtual car model is loaded by engine forces resulting from indirect force identification. This force-set includes combustion, inertia, piston slap and crank bearing forces, for engine harmonics from 0.5 to 10th order. Such forced response analysis yields vibration levels at every component, at every interface between components, and interior noise predictions. The target is to provide the vehicle NVH manager with the insight required to identify major causes for peak noise levels and to set targets and develop an action plan for every component design team.

Honda developed a 750cm3 V-4 engine adopting an elliptical piston, and began selling the “NR” motorcycle with the engine installed in 1992. The adoption of an elliptical piston and cylinder achieved a compact layout of eight valves, which consists of four intake valves and four exhaust valves per cylinder. This paper explains the features of an engine with such a layout, focusing on the following: 1) Multiple valves and short-stroke enable the 750cm3 engine to achieve 15,000rpm. 2) The engine is more compact and lightweight than an engine having the same displacement, and more powerful than one with twice as many cylinders (8 cylinders). Also, this paper describes the techniques giving improved blowby gas and oil consumption characteristics as related to the sealing property of the piston, cylinder and piston ring and achieving performance equivalent to a conventional motorcycle engine.

The technology for a new, high-strength piston material has been developed by using high pressure die casting (HPDC) method, which had a rapid rate of solidification. This method allowed the amount of Ni added to be increased to 5.5 mass%, raising the fatigue strength of the new material at temperatures of 523 K or higher by a factor of 1.5 over that of a conventional material made by gravity die casting (GDC). In addition, application of vacuum to the die cavity and using additional pressure enabled quality exceeding that of conventional GDC pistons. Pistons made from the newly developed material decreased engine friction by 4.4% and increased fuel efficiency by 2.2% in engine bench testing.

A single cylinder gasoline engine of displacement 125 cm3 for prototype was developed, and the fuel economy of this engine was improved by reducing friction and improving combustion. For reducing friction, various methods were innovated; enhancement of the oil film retention by modifying the striation finish on piston skirt, adding the needle bearing to the rocker arm shaft, press-fitting the bush into the small end of connecting rod, reducing contact pressure with the piston ring, and spray coating molybdenum disulfide onto the shift fork. By innovating these friction reduction methods, the friction of the engine was reduced by 6% compared to the previous model which was already employed the roller rocker arm and the offset cylinder. For improving combustion, the swirl control valve (SCV) was installed into the intake port. By the effect of SCV, both improvement of engine power and improving combustion under low load was achieved.

A 1.5 L downsizing turbocharged engine was developed to achieve both driving and environmental performance. The engine is intended to replace 1.8 - 2.4 L class NA engines. In downsizing turbocharged engines, mixture homogeneity is important for suppressing knocking and emission reduction. Particularly under high load, creating rapid combustion and a homogeneous mixture are key technologies. The authors used a long-stroke direct injection engine, which has outstanding rapid combustion and thermal efficiency, as a base engine meeting these requirements. They combined this with a high-tumble port and shallow-dish piston intended to support tumble flow. The combination enhanced flow within the cylinder. The combustion system was built to include a sodium-filled exhaust valve to reduce knocking and a multi-hole injector (six holes) for mixture homogeneity and to reduce the fuel wall wetting.

It is important to take action regarding environmental issues on a global scale, and automakers are adding downsized turbocharged engines to their line-ups as a means of reducing CO2 emissions, particularly in Europe. Honda has recently announced a next-generation powertrain series that realizes a good balance between environmental performance and driving pleasure. As part of this series, the company has developed a downsized and turbocharged 2.0L gasoline direct injection engine. This is a high-powered sports car engine positioned in the European “hot hatch” category. The development balanced engine power with good environmental performance.

We succeeded in creating of a very small wiper system for a CCD camera. The source of driving force of it is a vibration phenomenon of a piezoelectric element. In this paper, we will describe the structure and motion of our newly proposed wiper system and the fundamental motion of a piezoelectric element in it. And in order to clarify the driving principle, we carried out a theoretical analysis using the Principle of Hamilton. As a result, a driving mechanism was found, that is, when the blade displaces at a high angular velocity into one direction, the shaft rotates in the opposite direction. We were able to confirm the driving mechanism also by experiments.

A motor-assist system has been developed and employed for the "Insight' hybrid car. The system consists of an internal combustion engine as the primary power source, with an electric motor placed around the engine's crankshaft. Such construction reduces the system's volume significantly and offers more flexibility for the power plant layout. The system's functions include regeneration during braking, an idle stop mechanism, driving power assistance, and power supply for the 12V electrical system. A proper energy management method for various driving modes has been established by combining these functions, and fuel economy is significantly improved as a result. As another control feature, an active motor vibration control system compensates the idling vibration that is unique to three-cylinder engines.

The reciprocating frictional test is a common approach for screening the materials of the piston and sleeve of an automobile engine. The frictional speed of this test is, however, limited mainly by the vibration of test apparatus due to the absence of damping factors in engines. Considering that the frictional velocity between the piston and sleeve reaches around 20 m/s, common test conditions at less than 2 m/s are not sufficient to understand the real phenomena at a frictional interface. We therefore developed a high-speed reciprocating test apparatus that can operate at a much higher speed range and examined two materials used for piston rings and sleeves. For the piston ring material, nitrided SUS440C was used. Plates were made of centrifugal cast iron FC250 or cast aluminum AC2B, which were coated with Nikasil. The experimental results showed that the lubrication regimes of the two plate materials were different even at the same reciprocating speeds.