Search Results

Computer programs that simulate the wave propagation phenomena involved in manifold tuning mechanisms are used extensively in the design and development of internal combustion engines. Most comprehensive engine simulation programs are based on the governing equations of one-dimensional gas flow as these provide a reasonable compromise between modelling accuracy and computational speed. The propagation of pressure waves through pipe junctions is, however, an intrinsically multi-dimensional phenomenon. The modelling of such junctions within a one-dimensional simulation represents a major challenge, since the geometry of the junction cannot be fully represented but can have a major influence on the flow. This paper introduces a new pressure-loss junction model which can mimic the directionality imposed by the angular relationship of the pipes forming a multi-pipe junction. A simple technique for estimating the pressure-loss data required by the model is also presented.

The paper discusses the use of alcohol fuels in high performance pressure-charged engines such as are typical of the type being developed under the ‘downsizing’ banner. To illustrate this it reports modifications to a supercharged high-speed sports car engine to run on an ethanol-based fuel (ethanol containing 15% gasoline by volume, or ‘E85’). The ability for engines to be able to run on alcohol fuels may become very important in the future from both a global warming viewpoint and that of security of energy supply. Additionally, low-carbon-number alcohol fuels such as ethanol and methanol are attractive alternative fuels because, unlike gaseous fuels, they can be stored relatively easily and the amount of energy that can be contained in the vehicle fuel tank is relatively high (although still less than when using gasoline).

In order to reduce the development time involved in optimising the combustion system and valve timing of the internal combustion engine, an electro-hydraulic valve actuation system has been developed. The effects of various combustion strategies, including asymmetrical valve events, on emissions and efficiency, together with their sensitivity to EGR and AFR were investigated. In addition, the influence of the cylinder head design on in-cylinder charge motion and combustion was investigated by correlating airflow, tumble and swirl data to the heat release data obtained during dynamometer testing.

Charge-coolers have a significant effect on the performance of turbocharged internal combustion engines. For a comprehensive simulation of internal combustion engines fitted with such devices it is important to model the whole of the manifold system. A wave-action model of a charge-cooler boundary is proposed, together with a methodology for predicting the heat transfer coefficient of the device. This approach enables the instantaneous effectiveness of the charge-cooler to be predicted as a function of the mass flow rate through the device.

The paper critiques proposals for de-carbonizing transport and offers a potential solution which may be attained by the gradual evolution of the current fleet of predominantly low-cost vehicles via the development of carbon-neutral liquid fuels. The closed-carbon cycles which are possible using such fuels offer the prospect of maintaining current levels of mobility with affordable transport whilst neutralizing the threat posed by the high predicted growth of greenhouse gas emissions from this sector. Approaches to de-carbonizing transport include electrification and the adoption of molecular hydrogen as an energy carrier. These two solutions result in very expensive vehicles for personal transport which mostly lie idle for 95% of their life time and are purchased with high-cost capital.

The engine of a high performance sports car has been converted to operation on E85, a high alcohol-blend fuel containing nominally 85% ethanol and 15% gasoline by volume. In addition to improving performance, the conversion resulted in significant improvement in full-load thermal efficiency versus operation on gasoline. This engine has been fitted in a test vehicle and made flex-fuel capable, a process which resulted in significant improvements in both vehicle performance and tailpipe CO2 when operating solely on ethanol blends, offering an environmentally-friendly approach to high performance motoring. The present paper describes some of the highlights of the development of the flex-fuel calibration to enable the demonstrator vehicle to operate on any mixture of 95 RON gasoline and E85 in the fuel tank. It also discusses how through detailed development, the vehicle has been made to comply with primary pollutant emissions legislation on any ethanol-gasoline mixture up to E85.

Five different fuels, including gasoline, commercial E85, pure methanol and two mixtures of gasoline, ethanol and methanol, (GEM), configured to a target stoichiometric air fuel ratio have been investigated in a fully-optically-accessed engine. The work investigated effects of injection duration, and performed spray imaging, thermodynamic analysis of the combustion and OH imaging, for two fixed engine conditions of 2.7 and 3.7 bar NMEP at 2000 rpm. The engine was operated with constant ignition timing for all fuels and both loads. One of the most important results from this study was the suitability of a single type of injector to handle all the fuels tested. There were differences observed in the spray morphology between the fuels, due to the different physical properties of the fuels. The energy utilisation measured in this study showed differences of up to 14% for the different GEM fuels whereas an earlier in-vehicle study had showed only 2 to 3%.

Many new technologies are being developed to improve the fuel consumption of gasoline engines, including the combination of direct fuel injection with turbocharging in a so-called ‘downsizing’ approach. In such spark ignition engines operating on the Otto cycle, downsizing targets a shift in the operating map such that the engine is dethrottled to a greater extent during normal operation, thus reducing pumping losses and improving fuel consumption. However, even with direct injection, the need for turbine protection fuelling at high load in turbocharged engines - which is important for customer usage on faster European highways such as German Autobahns - brings a fuel consumption penalty over a naturally-aspirated engine in this mode of operation.

Iso-stoichiometric ternary blends - in which three-component blends of gasoline, ethanol and methanol are configured to the same stoichiometric air-fuel ratio as an equivalent binary ethanol-gasoline blend - can function as invisible "drop-in" fuels suitable for the existing E85/gasoline flex-fuel vehicle fleet. This has been demonstrated for the two principal means of detecting alcohol content in such vehicles, which are considered to be a virtual, or software-based, sensor, and a physical sensor in the fuel line. Furthermore when using such fuels the tailpipe CO₂ emissions are essentially identical to those found when the vehicle is operated on E85. Because of the fact that methanol can be made from a wider range of feed stocks than ethanol and at a cheaper price, these blends then provide opportunities to improve energy security, to reduce greenhouse gas emissions and to produce a fuel blend which could potentially be cheaper on a cost-per-unit-energy basis than gasoline or diesel.

Controlled auto ignition (CAI) is a form of combustion which uses an auto-ignited homogeneous air/fuel mixture but is controlled (or moderated) by regulating the quantity of internal exhaust gas residuals. In this paper, using a fully variable valve train and a newly developed exhaust valve control strategy, we substituted EGR with hot nitrogen or hot air. We found that the internal exhaust gas residuals have both thermal and chemical effects on CAI combustion. To investigate the thermal effect, nitrogen was used as it is a chemically inert gas. Although its temperature was raised to that of the internal exhaust gas residuals during testing, CAI combustion could not be promoted without assistance from a spark in a form of hybrid CAI, thus indicating that exhaust gas residuals have a chemical effect as well.

Designers are under increasing pressure to provide powertrain systems which meet tougher market and legislative requirements for:- performance, emissions and economy reliability and durability noise and refinement To meet increasing competition, powertrain products need to be “fast to market and right first time”. This implies the evolution of existing technology, comprising multicylinder reciprocating engines and gear transmissions, drawing on a database of decades of powerplant design experience. It is with this background that CAE has proven engineering value supporting key areas of powertrain engineering to meet these technological challenges in a cost effective and timely manner. This paper follows the analytical engineering of a typical component, the exhaust system. Particular emphasis is given to the manifold and downpipe components which duct gas from the cylinder head to the catalyst.

The homogeneous charge compression ignition-HCCI (also to be known as controlled auto ignition-CAI) engine concept has the potential to be highly efficient and to produce low NOx, carbon dioxide and particulate matter emissions. It experiences, however, problems with cold start, running at idle and high loads that together with controlling the combustion over the entire speed/load range limits its practical application. A solution to overcome these problems is to operate the engine in ‘hybrid mode’, where the engine operates in HCCI mode at low, medium and cruising loads and switch to spark ignition (SI) mode (or diesel mode-CI) at a cold start, idle and higher loads. To operate such ‘hybrid mode’ engine, a transition between SI and HCCI and SI modes, as a result of changes in engine speed and load must be seamless in operation, whilst keeping all relevant engine and combustion parameters in an acceptable range.

There is a great deal of interest in new technologies to assist in reducing the CO2 output of passenger vehicles, as part of the drive to meet the limits agreed by the EU and the European Automobile Manufacturer's Association ACEA, itself a result of the Kyoto Protocol. For the internal combustion engine, the most promising of these include gasoline direct injection, downsizing and fully variable valve trains. While new types of spray-guided gasoline direct injection (GDI) combustion systems are finally set to yield the level of fuel consumption improvement which was originally promised for the so-called ‘first generation’ wall- and air-guided types of GDI, injectors for spray-guided combustion systems are not yet in production to help justify the added complication and cost of the NOx trap necessary with a stratified combustion concept.

The Swedish Biomimetics 3000's μMist® platform technology has been used to develop a radically new injection system. This prototype system, developed and characterized with support from Lotus, as part of Swedish Biomimetics 3000®'s V₂IO innovation accelerating model, delivers improved combustion efficiency through achieving exceptionally small droplets, at fuel rail pressures far less than conventional GDI systems and as low as PFI systems. The system gives the opportunity to prepare and deliver all of the fuel load for the engine while the intake valves are open and after the exhaust valves have closed, thereby offering the potential to use advanced charge scavenging techniques in PFI engines which have hitherto been restricted to direct-injection engines, and at a lower system cost than a GDI injection system.