Search Results

Once the design of a door sheetmetal and accessories is confirmed, the acoustics of the door system depends on the sound package assembly. This essentially consists of a watershield which acts as a barrier and a porous material which acts as an absorber. The acoustical performance of the watershield and the reverberant sound build-up in the door cavity control the performance. This paper discusses the findings of a design study that was developed based on design of experiments (DOE) concepts to determine which parameters of the door sound package assembly are important to the door acoustics. The study was based on conducting a minimum number of tests on a five factor - two level design that covered over 16 different design configurations. In addition, other measurements were made that aided in developing a SEA model which is also compared with the findings of the results of the design study.

Recently, many authors have attempted to represent an automobile body in terms of experimentally derived frequency response functions (FRFs), and to couple the FRFs with a FEA model of chassis for performing a total system dynamic analysis. This method is called Hybrid FEA-Experimental FRF method, or briefly HYFEX. However, in cases where the chassis model does not include the bushing models, one can not directly connect the FRFs of the auto body to the chassis model for performing a total system dynamic analysis. In other cases when the chassis model includes the bushings, the bushing dynamic rates are modeled as constant stiffness rather than frequency dependent stiffness, the direct use of the HYFEX method will yield unsatisfactory results. This paper describes how the FRF's of the auto body and the frequency dependent stiffness data of the bushings can be combined with an appropriate mathematical formulation to better represent the dynamic characteristics of a full vehicle.

The Frequency Response Function (FRF) is a fundamental component to identifying the dynamic characteristics of a system. FRF's have a significant impact on modal analysis and root cause analysis of NVH issues. In most cases the FRF can be easily measured, but there are instances when the measurement is unobtainable due to spatial constraints. This paper outlines a simple experimental method for obtaining a high quality input-output FRF of a structure in areas where an impact hammer can not reach during impact testing. Traditionally, the FRF in such an area is obtained by using a load cell extender with a hammer impact excitation. A common problem with this device is a double hit, that yields unacceptable results.

Laboratory performance testing of larger tires requires system capability beyond larger diametric clearance and additional radial load capability. This paper describes a newly introduced Flat-Trac® tire test system designed for light truck tires and racing tires. Background on flat surface force and moment testing identifying the need for a system with more capability is presented. The MTS Flat-Trac LTR tire test system is introduced as a force and moment measurement system capable of testing light truck and racing tires. The first of these systems has been in operation at Bridgestone's Tokyo technical center since July 2002. Test results are presented to show that the Flat-Trac LTR (Light Truck/Racing) provides increased capability beyond the conventional Flat-Trac III CT (Cornering and Traction) system. Cornering force and longitudinal force test results are compared to show agreement between the Flat-Trac LTR and Flat-Trac CT systems.

Shudder vibration of a hydraulic power steering system during parking maneuver was studied with numerical and experimental methods. To quantify vibration performance of the system and recognize important stimuli for drivers, a shudder metric was derived by correlation between objective measurements and subjective ratings. A CAE model for steering wheel vibration analysis was developed and compared with measured data. In order to describe steering input dependency of shudder, a new dynamic friction modeling method, in which the magnitude of effective damping is determined by average velocity, was proposed. The developed model was validated using the measured steering wheel acceleration and the pressure change at inlet of the steering gear box. It was shown that the developed model successfully describes major modes by comparing the calculated FRF of the hydraulic system with measured one from the hydraulic excitation test.

The popularity of AWD passenger vehicles presents a challenge to provide car-like drive-train NVH within a relatively small package space. This paper describes a drive-train NVH case study in which analysis and test were used, in conjunction, to solve an NVH problem. Also, it details a systematic process of using the analytical model to identify and resolve similar problems. The particular problem for this case study is a noise and vibration issue occurring at 75 MPH primarily in the middle seat of an all-wheel drive vehicle. Tests indicated that it may be due to propeller shaft imbalance. Analysis results showed good correlation with the tests for that loading condition. Several solutions were identified, which were confirmed by both test and analysis. The most cost-effective of these solutions was implemented.

Powertrain mounts are one of the important design characteristics of a vehicle. Powertrain is mostly mounted to the front subframe and once installed in a vehicle, powertrain mounting has an important role in determining the vehicle vibration characteristics. A good mounting system isolates engine input vibration from the vehicle body and minimizes the effect of road inputs to the customer. This paper discusses results of several dynamic models as they relate to noise, vibration and harshness (NVH) and compares the accuracy of these models. Various powertrain models are studied and their accuracy in comparison with full a vehicle model is discussed.

This paper presents the results of a study of using a neural network black box model of a shock absorber of an ATV (All Terrain Vehicle, four wheel drive, off road, single person vehicle) for accurate load modeling. This study is part of a larger investigation into the dynamic behavior and associated fatigue of an ATV vehicle, which is conducted under the auspices of the Fatigue Design and Evaluation Committee of SAE of North America (www.fatigue.org). The general objectives are to develop new correlated methodologies that will allow engineers to predict the durability of components of proposed vehicles by means of a “digital prototype” simulation. Current state of the art multi body dynamics predictions use linear frequency response functions or non-linear polynomial approximations to describe the behavior of non-linear suspension components such as shock absorbers or bushings.

This paper describes a diesel vehicle NVH development process which has been applied to achieve a number of best in class products in the European diesel marketplace. It focuses upon: Key diesel vehicle NVH issues Critical success factors in the NVH development process NVH methodologies, tools and techniques which support this process Case studies using results taken largely from a luxury sedan vehicle development program are used to highlight the issues and to demonstrate the success of this process in achieving a vehicle with high diesel appeal. The paper concludes with an insight of how this process is being adapted and refocused to reflect the anticipated requirements of the potential US diesel vehicle marketplace.

The quest to simulate noise problems has led to the building of larger and more detailed finite element models in order to perform vibration solutions to higher frequencies. This leads to the building of solid finite element models of complex geometries, such as castings, which might previously have contained less detail or even been built with shell elements. Unfortunately, detailed geometric representations used to build models do not always agree with as built parts and lead to discrepancies between analysis results and test data. This paper presents an approach that reduces the time and cost necessary to identify these differences.

The scope of this paper is to describe how system level NVH targets are cascaded down to sub system level targets using the technique of Transfer Path Analysis (TPA). In the early stages of a vehicle design program target vehicles for the new vehicle are selected based on their subjective Noise, Vibration, and Harshness (NVH) performance. A reference vehicle for the new product will be selected which will be used as a baseline vehicle for the whole vehicle program. Noise and vibration measurements will be taken on both the reference and target vehicles under multiple load conditions. The simulation target for the new product will be derived from the measurements of reference vehicle, measurements of target vehicle, and the simulation of reference vehicle model. Reverse Transfer Path Analysis tools will be used to quantify the subsystem targets for the new vehicle based on the simulation targets and design intent simulation models of new product.

Cavity reinforcement materials are used in the automotive industry to stiffen hollow cavities in vehicle body constructions. Typical areas of use include the engine rails, rocker panels, roof support or any other cavity in need of structural reinforcement. Use of these materials can allow for significant reductions in vehicle weight and increase structural stiffness with minimal impact to production tooling. Additional benefits can be gained by using the material as a physical barrier to the propagation of noise, water and dust. The objective of this paper is to describe a case study which implemented a new type of cavity reinforcing material to improve low frequency vehicle noise and vibration characteristics.

Internal combustion engine noise and vibration are major issues for car makers, and these are even more important for High-Level Pick-ups and SUV's which applies modern diesel engines. One important player in this scenario is the second-order unbalanced forces vibration produced by the conventional in-line 4-cylinder engine configurations, which leads to high-frequency excitation of vehicle's structure and consequent internal noise. This paper studies a balancer shaft solution for the mentioned engine configuration, as well as major design alternatives and development process and issues. This paper also presents an example of a balancer shaft design and development for a high speed diesel engine, as well as proposes a design/decision matrix methodology. Such methodology, which can be applied to any design or engineering case, helps design engineers make the right decision amongst different options by using a very simple and objective matrix.

Brake groan noise and vibration occurs in a stopped vehicle by the simultaneous application of torque to the wheel and the gradual release of brake pressure. Eventually the torque load breaks the friction between pad and rotor causing slippage and energy release. If the torque load is not large enough to maintain slippage, a sustained stick-slip vibration, called groan, can occur which transmits a low frequency noise to the vehicle interior. In some cases the noise levels caused by groan can be objectionable, thus procedures for developing remedial designs are needed. To this end, a project was performed to analytically simulate groan vibration in a vehicle with a McPherson strut type suspension. The goal was to demonstrate that analytical models could be used to simulate groan behavior and to identify suspension components that affect the groan behavior. The ADAMS software was used to model a brake/suspension system.

Sunroof is placed in certain high-end vehicles to give user a better driving experience. All automakers are searching alternatives to reduce weight and cost in the vehicle, in which sunroofs are also impacted. Some alternatives are already applied, as a honeycomb paper used in some sunshades that presents benefits, as less weight and with a good cost reduction. Although, due the reduced weight for this part produced in this material, it shows more susceptibility to reproduce the vibration that vehicle propagates in movement, especially in bad condition roads. The sunroof assembly is dependent of the roof reinforcement and roof skin, but in this special case, the validation could be done in the components itself because the interaction of the sunshades is directly dependent of the other sunroof parts, as rails and front frame.

The growing competition of the automotive market makes more and more necessary the reduction of development time and consequently, the increase of the capacity to quickly respond to the launching of the competitors. One of the most costly phases on the vehicle development process is the field durability test, both in function of the number of prototypes employed and the time needed to its execution. More and more diffused, the fatigue life prediction methods have played an important part in the durability analysis via CAE. Nevertheless, in order they can be reliable and really being able to reduce the development time and cost, they need to be provided with load cases that can accurately represent the field durability tests. This work presents a CAE approach used for light trucks in order to get a reasonable understanding of component durability behavior due to payload increase. In general, road load data is not available for a new payload condition.

One of the major NVH concerns for automobile manufacturers is the response of a vehicle to the impact of the tire as it encounters a road discontinuity or bump. This paper describes methods for analyzing the impact response of a vehicle to such events. The test vehicle is driven on a dynamometer, on which a bump simulating cleat is mounted. The time histories of the cleat impact response of the vehicle can be classified as a transient and a repeated signal, which should be processed in a special way. This paper describes the related signal processing issues, which include converting the time data into a continous spectrum, determination of the correct scaling factor for the analyzed spectrum, and smoothing out harmonics and fluctuations in the signal. This procedure yields a smooth frequency spectrum with a correctly scaled amplitude, in which the frequency contents can be easily identified.

The 45RFE is a new generation electronically controlled rear wheel drive automatic transmission. It employs real-time feedback, closed-loop modulation of shift functions to achieve outstanding shift quality and to meet demanding durability goals. It uses no shift valves; all friction element applications are effected with high-flow electro-hydraulic solenoid valves. A unique gear train arrangement of three planetary carriers allows all sun gears and annulus gears to have the same number of teeth respectively and use a common pinion gear in all carriers, resulting in significant manufacturing simplification. The three-planetary system is designed for four forward ratios of 3.00, 1.67, 1.00 and 0.75 and one reverse gear ratio equal to the low gear ratio. A fifth ratio of 1.50 is used only in certain kick-down shift sequences for highway passing. A sixth forward ratio, an additional overdrive ratio of 0.67, is available in the hardware.

The U.S. Environmental Protection Agency, U.S. Department of Transportation's National Highway and Traffic Safety Administration, and the California Air Resources Board have recently released proposed new regulations for greenhouse gas emissions and fuel economy for light-duty vehicles and trucks in model years 2017-2025. These proposed regulations intend to significantly reduce greenhouse gas emissions and increase fleet fuel economy from current levels. At the fleet level, these rules the proposed regulations represent a 50% reduction in greenhouse gas emissions by new vehicles in 2025 compared to current fleet levels. At the same time, global growth, especially in developing economies, should continue to drive demand for crude oil and may lead to further fuel price increases. Both of these trends will therefore require light duty vehicles (LDV) to significantly improve their greenhouse gas emissions over the next 5-15 years to meet regulatory requirements and customer demand.

This paper dis cusses the development of a nonlinear shock absorber model for low-frequency CAE-NVH applications of body-on-frame vehicles. In CAE simulations, the shock absorber is represented by a linear damper model and is found to be inadequate in capturing the dynamics of shock absorbers. In particular, this model neither captures nonlinear behavior of shock absorbers nor distinguishes between compression and rebound motions of the suspension. Such an inadequacy limits the utility of CAE simulations in understanding the influence of shock absorbers on shake performance of body-on-frame vehicles in the low frequency range where shock absorbers play a significant role. Given this background, it becomes imperative to develop a shock absorber model that is not only sophisticated to describe shock absorber dynamics adequately but also simple enough to implement in full-vehicle simulations. This investigation addresses just that.