Search Results

Till recently supercharging was the most accepted technique for boost solution in gasoline engines. Recent advents in turbochargers introduced turbocharging technology into gasoline engines. Turbocharging of gasoline engines has helped in powertrains with higher power density and less overall weight. Along with the advantages in performance, new challenges arise, both in terms of thermal management as well as overall acoustic performance of powertrains. The study focuses mainly on NVH aspects of turbocharging of gasoline engines. Compressor surge is a most common phenomenon in turbochargers. As the operating point on the compressor map moves closer to the surge line, the compressor starts to generate noise. The amplitude and frequency of the noise depends on the proximity of the operating point to the surge line. The severity of noise can be reduced by selecting a turbocharger with enough compressor surge margin.

The bolted joints in suspension systems are subjected to severe external service loads during vehicle operation. To prevent the loaded joint from loosening and allowing it to retain its potential energy stored during assembly, a holistic design approach is needed. This paper explains the methodology to design and optimize bolted joints for the suspension systems of a modern 7-seater sports utility vehicle.

The ever-increasing customer expectations put a lot of pressure on car manufacturers to constantly reduce the noise, vibration, and harshness (NVH) levels. This paper presents the holistic approach used to achieve best-in-class NVH levels in a modern high-power density 1.5 lit 4-cylinder diesel engine. In order to define the NVH targets for the engine, global benchmark engines were analysed with similar cubic capacity, power density, number of cylinders and charging system. Moreover, a benchmark diesel engine (considered as best-in-class in NVH) was measured in a semi-anechoic chamber to define the engine-level NVH targets of the new engine. The architecture selection and design of all the critical components were done giving due consideration to NVH behaviour while keeping a check on the weight and cost.

The focus on driver and occupant safety as well as comfort is increasing rapidly while designing commercial vehicles in India. Improvements in the road network have enhanced road transport for commercial vehicles. Apart from the cost of operation and fuel economy, the commercial vehicles must deliver goods within stipulated time. These factors resulted in higher speed of operation for commercial vehicles. The design should not compromise the safety of the vehicle at these higher speeds of operation. The vehicle should obey the driver’s intended direction at all speeds and the response of the vehicle to driver input must be predictable without much larger surprises which can lead to accidents. The commercial vehicles are designed with rigid axle and RCB type steering system. This suspension and steering design combination introduce steering errors when vehicle travel over bump, braked and while cornering.

A typical powertrain mount design process starts with performing the system calculations to determine optimum mount parameters, viz. position, orientation and stiffness values to meet the desired NVH targets. Therefore, a 6 degrees of freedom lumped parameter system of powertrain and mounts is modelled in Matlab®. The approach is to decouple the torque roll axis mode from the remaining five rigid body modes so that the response to the torque pulses is predominantly ‘oscillations about Torque Roll Axis’. This is achieved by optimizing the above mount parameters within specified constraints so that ‘Rotation about the torque roll axis’ is one of the natural modes of vibration. The tool developed here uses ‘Particle Swarm Optimization(PSO) algorithm’ because of its ease of implementation and better convergence to the solution. The algorithm is programmed in TK solver®.

The cylinder block for the power train has always been a classic example of concurrent engineering in which disciplines like NVH, Durability, thermal management and lubrication system layout contribute interactively for concept design. Since the concept design is based on engineering judgment and is an estimated design, the design iterations for optimization are inevitable. This paper aims at outlining a systematic approach for design of crankcase for fatigue which would eliminate design iterations for durability. This allows a larger scope for design improvement at the concept stage as the design specifications are not matured at this stage. A process of stress optimization is adopted which gives accurate dimensional input to design. The approach is illustrated with a case study where an existing crankcase was optimized for fatigue and significant weight reduction was achieved.

Automated manual transmission (AMT) is often preferred by car manufacturers as entry-level automation technology. The AMT technology can provide the comfort of an automatic gearbox at a reasonable cost impact over manual transmission (MT). This paper explains the unique approach to define the gear-shift map of a compact sports utility vehicle (SUV) considering the unique requirements of the Indian market. The real-world measurements revealed that an aggressive shift pattern with delayed upshifts and quick downshifts can deliver good low-end drivability and performance while compromising on fuel economy (FE). Moreover, the chassis dyno measurements in the modified Indian drive cycle (MIDC) indicated lower FE values. On the other hand, a shift pattern with early upshifts and delayed downshifts could help in achieving a better FE while compromising on drivability and performance. Hence, a unique approach is used to derive the most optimal gear-shift map for each operating gear.

Dual mass flywheel (DMF) is an excellent solution to improve the noise, vibration and harshness (NVH) characteristic of any vehicle by isolating the driveline from the engine torsional vibrations. For the same reason, DMFs are widely used in high power-density diesel and gasoline engines. However, the real-world usage conditions pose a lot of challenges to the structural robustness of the DMF. In the present work, a new methodology is developed to evaluate the robustness of a DMF fitted in a compact sports utility vehicle (SUV) with rear-wheel drive architecture. The abuse conditions (mis-gear, sudden braking, etc) in the real-world usage could lead to a sudden engine stall leading to an abnormally high angular deceleration of the driveline components. The higher rate of deceleration coupled with the higher rotational moment of inertia of the systems might end up in introducing a significantly high impact torque on the DMF.

In automotive door engineering, fitting the side door glass surface from styling into the cylinder or torus is the basic requirement. Optimization is required to do this, which requires a solver which could be efficacious for best surface fitting. This paper propounds a methodology which could be used for fitting a side door glass surface from styling into the cylinder or torus. The method will significantly help in developing the required surface and can successfully eliminate the cumbersome manual calibrations. The mathematical model mentioned is a novel approach based on “Particle Swarm Optimization” (“PSO” will be used to represent in the paper) towards surface optimization technique. VB script is used to make it applicable in CATIA but could be easily applied in any other programming language like python, java etc. Usually the surface fitting problems deals with the initial guess of the required surface and then its further optimization.

The maximum power produced by the Engine is utilized in overcoming the Aerodynamic resistance while the remaining has been used to overcome rolling and climbing resistance. Increasing emission and performance demands paves way for advanced technologies to improve fuel efficiency. One such way of increasing the fuel efficiency is to reduce the aerodynamic drag of the vehicle. Buses emerged as the common choice of transport for people in India. By improving the aerodynamic drag of the Buses, the diesel consumption of a vehicle can be reduced by nearly about 10% without any upgradation of the existing engine. Though 60 to 70 % of pressure loads act on the frontal surface area of the buses, the most common techniques of reducing the drag in buses includes streamlining of the surfaces, minimizing underbody losses, reduced frontal area, pressure difference between the front & rear area and minimizing of flow separation & wake regions.

Aerodynamics of on-road vehicles has come to the limelight in the recent years. Better aerodynamic design of vehicle would improve vehicle fuel efficiency with increased acceleration performance. To obtain best aerodynamic body, the series of design modifications and different testing methodologies must be involved in vehicle design and validation phase. Wind tunnel aerodynamic force measurement, road load determination and computational fluid dynamics were the common methods used to evaluate the aerodynamic behavior of the vehicle body. As a novel approach, the present work discusses about the on-road (Real time) testing methodology that is aimed to evaluate the aerodynamic performance of vehicle body using surface pressure mapping. A 64-Channel digital pressure scanner has been utilized in this work for mapping the pressure at different locations of the typical vehicle body.

A hydraulic power train assembly of an agricultural tractor is meant to lift the heavy implements during field operations and transportation. As it is a crucial member of the tractor for its usage, so the power train assembly needs a properly designed lift arm, rocker arm assembly with better strength and stiffness. There are a standard like IS12224, IS4468 which regulates the test method for hydraulic power and lift capacity of tractor and the layout of hydraulic three point linkage. Computer aided engineering techniques followed by laboratory testing have been deployed in the earlier stages of the product design & development itself to deliver the first time right products to the customer. In this paper, a virtual simulation process has been established to design an agricultural tractor hydraulic lift arm to meet the above requirements. A Design Verification Plan (DVP) has been developed consisting of 3 load cases.

The input shafts are conventionally developed through Hot forging route. Considering upcoming new technologies the same part was developed through cold forging route which resulting in better Mechanical properties than existing hot forging process. It has added benefit of cost as well as environmental friendly. Generally, the part like Input shaft which having gear teeth, splines etc., will be manufactured through Hot forging process due to degree of deformation, availability of press capacity, diameter variations etc., This process consumes more energy in terms of electricity for heating the bar and also creates pollution to the atmosphere. Automotive input shaft design modified to accommodate cold forging process route to develop the shaft with press capacity of 2500T which gives considerable benefit in terms of mechanical and metallurgical Properties, close dimensional tolerances, less machining time, higher material yield when compared to hot forging and metal cutting operation.

It is imperative that all automobile manufacturers conduct vehicle level benchmarking at the initial stage of any new project. From the benchmark information, the manufacturers can set relevant targets for their own vehicles under development. In this regard, an accurate prediction of the engine operating points can improve the correlation of the measured fuel economy of the benchmark vehicle. The present work describes a novel method that can be used for the accurate prediction of the engine operating points of any benchmark vehicle. Since the idea of instrumenting the crankshaft/driveshaft with torque transducers is a costlier and time-consuming process, the proposed method can be effective in reducing the benchmarking. Hence, the objective of this work is to develop a mathematical model to calculate the real-time engine operating points (engine speed and torque) using parameters like vehicle speed, accelerator pedal map, driveline inertia, vehicle coastdown force and gradient.

NVH is becoming one of the major factor for customer selection of vehicle along with parameters like fuel economy and drivability. One of the major NVH challenges is to have a vehicle with aggressive drivability and at the same time with acceptable noise and vibration levels. This paper focuses on the compact utility vehicle where the howling noise is occurring at higher rpm of the engine. The vehicle is powered by three cylinder turbocharged diesel engine. The noise levels were higher above 2500 rpm due to the presence of structural resonance. Operational deflection shapes (ODS) and Transfer path analysis (TPA) analysis was done on entire vehicle and powertrain to find out the major reason for howling noise at higher engine rpm. It is observed that the major contribution for noise at higher rpm is due to modal coupling between powertrain, half shaft and vehicle sub frame.

This paper deals with an analytical method to calculate the press-fit tolerance and fits between gears and shaft for automotive applications. The relative interferences increase sharply in the small diameter range, therefore one must be especially careful when designing small diameter joints. The strength of press-fit depends on the amount of relative interference; extreme interference leads to excessive contact stresses between the gear and shaft eventually leading to failure. Too little interference leads to slippage of gear on the shaft. In the press fit connection a shaft's spline rolling operation and gear internal broaching is eliminated. It is more economical than a conventional spline connection. Press fit connections are used in various transmission between a shaft and a gear. They are used in 6 speed transmission to 9-speed transmission for (German based Vehicle Manufacturer) heavy and light commercial vehicle company.

This paper presents the analysis and experimental validation of c-spring and its stiffness properties in the gear shift synchronizer system. A synchronizer assembly for a transmission comprises of a synchronizer hub carried by a torque delivery shaft and a cone clutch member carried by a gear and a synchronizer blocking ring. The gear shift sleeve is meshing over the teeth of the clutch hub. The c-spring is positioned in the inner circumference of the rim position of the clutch hub and strut keys will be positioned at the slots on the clutch hub, which are usually 120 degree apart. As the sleeve moves while gear shifting, it pushes down the strut keys which compress the C-spring radially inward; this gives the strut load. The strut keys, which are pushed down by the sleeve, will apply force on the c-spring from radial directions. Since the c-spring is in the shape of an arc it is assumed as a curved beam for the analysis.

The introduction of CAFE (Corporate Average Fuel Economy) norms has put a lot of importance on improving the fuel economy of passenger car vehicles. One of the areas to improve the fuel economy is by reducing engine friction. Camshaft drive torque reduction is one such area that helps in engine friction reduction. This paper explains the camshaft drive torque optimization work done on a passenger car Diesel engine with DOHC (double overhead camshaft). The exhaust camshaft of the engine drives the high-pressure Fuel Injection Pump (FIP) in addition to valve actuation. Camshaft drive torque is reduced by reducing the chain load. This is done through optimum phasing of the FIP lobe that drives the fuel injection pump and the cam lobe actuating the exhaust valves. Additional boundary condition for the phasing is ensuring that the FIP lobe is in the fall region of its profile while the piston is at TDC. This helps in avoiding rail pressure fluctuation.

Plastics are prone to photo oxidative and thermal oxidative degradation under usage conditions due to their chemical nature. From sustainability and cost standpoint, there is an increasing focus on Mold-In-Color (MIC) plastic materials. Simultaneously customer’s expectations on the perceived quality of these MIC parts has been increasing with attractive color and glossy appearance. A study was conducted to analyze the product quality and durability aspects over a prolonged exposure to accelerated weathering condition. Material selected for this study were injection molded specimens of ABS and PC-ABS used in automotive passenger vehicles. Comparative analysis was conducted before and after weathering exposure at defined intervals by using Fourier Transform infra-red spectrometer (FTIR), differential scanning colorimetry (DSC), universal testing machine (UTM), Izod impact tester and microscope to understand the impact on their chemical and mechanical properties.

The present work is concerned with the computation of in-cylinder flow field of a naturally aspirated single cylinder diesel engine using 3D CFD methods. Flow in the intake port and across the valve and subsequent in-cylinder flow is simulated for different valve lift conditions. The in-cylinder flow field is thoroughly analyzed for the flow asymmetry, number of vortices and swirling motion. Predicted velocity field at 20 mm and 92 mm sections from the cylinder head is compared with those obtained from the experiments. Doppler global velocimetry has been used to measure the velocity vectors at the two earlier identified sections for vale lifts of 2, 4, 6, 8 and 9 mm. The development of flow in the longitudinal and transverse directions is studied from the measured velocity vectors. The evolution of the global in-cylinder flow structure with respect to the lift is presented.