Search Results

Till recently supercharging was the most accepted technique for boost solution in gasoline engines. Recent advents in turbochargers introduced turbocharging technology into gasoline engines. Turbocharging of gasoline engines has helped in powertrains with higher power density and less overall weight. Along with the advantages in performance, new challenges arise, both in terms of thermal management as well as overall acoustic performance of powertrains. The study focuses mainly on NVH aspects of turbocharging of gasoline engines. Compressor surge is a most common phenomenon in turbochargers. As the operating point on the compressor map moves closer to the surge line, the compressor starts to generate noise. The amplitude and frequency of the noise depends on the proximity of the operating point to the surge line. The severity of noise can be reduced by selecting a turbocharger with enough compressor surge margin.

The ever-increasing customer expectations put a lot of pressure on car manufacturers to constantly reduce the noise, vibration, and harshness (NVH) levels. This paper presents the holistic approach used to achieve best-in-class NVH levels in a modern high-power density 1.5 lit 4-cylinder diesel engine. In order to define the NVH targets for the engine, global benchmark engines were analysed with similar cubic capacity, power density, number of cylinders and charging system. Moreover, a benchmark diesel engine (considered as best-in-class in NVH) was measured in a semi-anechoic chamber to define the engine-level NVH targets of the new engine. The architecture selection and design of all the critical components were done giving due consideration to NVH behaviour while keeping a check on the weight and cost.

The focus on driver and occupant safety as well as comfort is increasing rapidly while designing commercial vehicles in India. Improvements in the road network have enhanced road transport for commercial vehicles. Apart from the cost of operation and fuel economy, the commercial vehicles must deliver goods within stipulated time. These factors resulted in higher speed of operation for commercial vehicles. The design should not compromise the safety of the vehicle at these higher speeds of operation. The vehicle should obey the driver’s intended direction at all speeds and the response of the vehicle to driver input must be predictable without much larger surprises which can lead to accidents. The commercial vehicles are designed with rigid axle and RCB type steering system. This suspension and steering design combination introduce steering errors when vehicle travel over bump, braked and while cornering.

A typical powertrain mount design process starts with performing the system calculations to determine optimum mount parameters, viz. position, orientation and stiffness values to meet the desired NVH targets. Therefore, a 6 degrees of freedom lumped parameter system of powertrain and mounts is modelled in Matlab®. The approach is to decouple the torque roll axis mode from the remaining five rigid body modes so that the response to the torque pulses is predominantly ‘oscillations about Torque Roll Axis’. This is achieved by optimizing the above mount parameters within specified constraints so that ‘Rotation about the torque roll axis’ is one of the natural modes of vibration. The tool developed here uses ‘Particle Swarm Optimization(PSO) algorithm’ because of its ease of implementation and better convergence to the solution. The algorithm is programmed in TK solver®.

Range anxiety is one of the major factors to be dealt with for increasing penetration of EVs in current Automotive market. The major reasons for range anxiety for customers are sparse charging infrastructure availability, limited range of Electric vehicles and range uncertainty due to diverse real-world usage conditions. The uncertainty in real world range can be reduced by increasing the correlation between the testing condition during vehicle development and real-world customer usage condition. This paper illustrates a more accurate test methodology development to derive the real-world range in electric vehicles with experimental validation and system level analysis. A test matrix is developed considering several variables influencing vehicle range like different routes, drive modes, Regeneration levels, customer drive behavior, time of drive, locations, ambient conditions etc.

In any engine cooling system, de-aeration capability of the system plays a very critical role to avoid over heating of an engine. In general, with recovery bottle engine cooling system there is one vent hose from radiator pressure cap to the recovery bottle and coolant in the bottle is exposed to atmospheric pressure. From this vent hose air bubbles will move to recovery bottle from the engine and radiator when pressure in the system exceeds pressure cap setting. With this arrangement, de-aeration from the engine will happen when thermostat opens only and till that time air bubbles will be in the engine only and in this time there will be chance of overheating at some critical conditions because of air pockets in to the engine water jacket and the entrained air in the cooling circuit. Also, secondly 100 % initial filling cannot be achieved.

The cylinder block for the power train has always been a classic example of concurrent engineering in which disciplines like NVH, Durability, thermal management and lubrication system layout contribute interactively for concept design. Since the concept design is based on engineering judgment and is an estimated design, the design iterations for optimization are inevitable. This paper aims at outlining a systematic approach for design of crankcase for fatigue which would eliminate design iterations for durability. This allows a larger scope for design improvement at the concept stage as the design specifications are not matured at this stage. A process of stress optimization is adopted which gives accurate dimensional input to design. The approach is illustrated with a case study where an existing crankcase was optimized for fatigue and significant weight reduction was achieved.

Dual mass flywheel (DMF) is an excellent solution to improve the noise, vibration and harshness (NVH) characteristic of any vehicle by isolating the driveline from the engine torsional vibrations. For the same reason, DMFs are widely used in high power-density diesel and gasoline engines. However, the real-world usage conditions pose a lot of challenges to the structural robustness of the DMF. In the present work, a new methodology is developed to evaluate the robustness of a DMF fitted in a compact sports utility vehicle (SUV) with rear-wheel drive architecture. The abuse conditions (mis-gear, sudden braking, etc) in the real-world usage could lead to a sudden engine stall leading to an abnormally high angular deceleration of the driveline components. The higher rate of deceleration coupled with the higher rotational moment of inertia of the systems might end up in introducing a significantly high impact torque on the DMF.

In automotive door engineering, fitting the side door glass surface from styling into the cylinder or torus is the basic requirement. Optimization is required to do this, which requires a solver which could be efficacious for best surface fitting. This paper propounds a methodology which could be used for fitting a side door glass surface from styling into the cylinder or torus. The method will significantly help in developing the required surface and can successfully eliminate the cumbersome manual calibrations. The mathematical model mentioned is a novel approach based on “Particle Swarm Optimization” (“PSO” will be used to represent in the paper) towards surface optimization technique. VB script is used to make it applicable in CATIA but could be easily applied in any other programming language like python, java etc. Usually the surface fitting problems deals with the initial guess of the required surface and then its further optimization.

The maximum power produced by the Engine is utilized in overcoming the Aerodynamic resistance while the remaining has been used to overcome rolling and climbing resistance. Increasing emission and performance demands paves way for advanced technologies to improve fuel efficiency. One such way of increasing the fuel efficiency is to reduce the aerodynamic drag of the vehicle. Buses emerged as the common choice of transport for people in India. By improving the aerodynamic drag of the Buses, the diesel consumption of a vehicle can be reduced by nearly about 10% without any upgradation of the existing engine. Though 60 to 70 % of pressure loads act on the frontal surface area of the buses, the most common techniques of reducing the drag in buses includes streamlining of the surfaces, minimizing underbody losses, reduced frontal area, pressure difference between the front & rear area and minimizing of flow separation & wake regions.

A hydraulic power train assembly of an agricultural tractor is meant to lift the heavy implements during field operations and transportation. As it is a crucial member of the tractor for its usage, so the power train assembly needs a properly designed lift arm, rocker arm assembly with better strength and stiffness. There are a standard like IS12224, IS4468 which regulates the test method for hydraulic power and lift capacity of tractor and the layout of hydraulic three point linkage. Computer aided engineering techniques followed by laboratory testing have been deployed in the earlier stages of the product design & development itself to deliver the first time right products to the customer. In this paper, a virtual simulation process has been established to design an agricultural tractor hydraulic lift arm to meet the above requirements. A Design Verification Plan (DVP) has been developed consisting of 3 load cases.

NVH is becoming one of the major factor for customer selection of vehicle along with parameters like fuel economy and drivability. One of the major NVH challenges is to have a vehicle with aggressive drivability and at the same time with acceptable noise and vibration levels. This paper focuses on the compact utility vehicle where the howling noise is occurring at higher rpm of the engine. The vehicle is powered by three cylinder turbocharged diesel engine. The noise levels were higher above 2500 rpm due to the presence of structural resonance. Operational deflection shapes (ODS) and Transfer path analysis (TPA) analysis was done on entire vehicle and powertrain to find out the major reason for howling noise at higher engine rpm. It is observed that the major contribution for noise at higher rpm is due to modal coupling between powertrain, half shaft and vehicle sub frame.

This paper deals with an analytical method to calculate the press-fit tolerance and fits between gears and shaft for automotive applications. The relative interferences increase sharply in the small diameter range, therefore one must be especially careful when designing small diameter joints. The strength of press-fit depends on the amount of relative interference; extreme interference leads to excessive contact stresses between the gear and shaft eventually leading to failure. Too little interference leads to slippage of gear on the shaft. In the press fit connection a shaft's spline rolling operation and gear internal broaching is eliminated. It is more economical than a conventional spline connection. Press fit connections are used in various transmission between a shaft and a gear. They are used in 6 speed transmission to 9-speed transmission for (German based Vehicle Manufacturer) heavy and light commercial vehicle company.

Development of Hybrid Electric Vehicles (HEVs) and Battery Electric Vehicles (BEVs) is gaining traction across all geographies to help meet increasing fuel economy regulations and as a pathway to offset concerns due to climate change. But HEVs and EVs have so far been a nascent market for India. These technologies have primarily shifted towards Lithium-ion batteries (LIB) for energy storage due to its high energy and power densities. In order to make actual business sense of these technologies, of which, battery is a major cost driver, it is necessary for these batteries to provide similar performance and life expectancy across the operating boundary of the vehicles, as well as provide the requirements at a competitive cost. In other words, the LIBs have to sustain the normal life cycle requirements and withstand wide range of storage temperatures that the conventional gasoline/diesel vehicles have been good at and still ensure good life.

The present work is concerned with the computation of in-cylinder flow field of a naturally aspirated single cylinder diesel engine using 3D CFD methods. Flow in the intake port and across the valve and subsequent in-cylinder flow is simulated for different valve lift conditions. The in-cylinder flow field is thoroughly analyzed for the flow asymmetry, number of vortices and swirling motion. Predicted velocity field at 20 mm and 92 mm sections from the cylinder head is compared with those obtained from the experiments. Doppler global velocimetry has been used to measure the velocity vectors at the two earlier identified sections for vale lifts of 2, 4, 6, 8 and 9 mm. The development of flow in the longitudinal and transverse directions is studied from the measured velocity vectors. The evolution of the global in-cylinder flow structure with respect to the lift is presented.

This paper reviews application of D-Cycle technology to compact tractor diesel engine for improving efficiency & power. The study considers design challenges that are presented for accommodating D-Cycle technology in engine. The paper also covers resolving those challenges with established technical solutions. The study focuses on modifying conventional compact 4-stroke diesel engine with the intention of keeping design changes to a minimum level for incorporating differential stroke technology. Designing of vertically splitting lightweight piston crown which can be smoothly engaged and separated from main piston body without any impact, stem rod which connects piston crown with rocker arm, split connecting rod and rocker arm which is actuated by extra actuating camshaft in addition of present valvetrain camshaft, are covered. Lubrication of additional actuating camshaft is done by extending existing oil galleries.

Tractor hitch control system is used for attaching and operating various Agricultural Implements and for operating tipping trailer. The system has also got provision to attach additional Aux valves for rear and front mounted attachments. The rear mounted implements are coupled to the tractor using Three Point Linkage (3PL) System. The hitch hydraulics system consists of hydraulic pump, filter, piping’s, fittings and hydraulics lift unit. Hydraulics lift unit consists of a proportional control valve, cylinder, piston and power linkages. Conventional control valve is hydro mechanical part operated by mechanical linkages. The control valve and linkages plays major role in performance of hydraulics system. Hydraulics is required to operate in extreme conditions of soils such as very soft like sand to very hard like black cotton sand.

This paper explains the methodology to design a high power-density diesel engine capable of 180 bar peak firing pressure yet achieving the lowest level of mechanical friction. The base engine architecture consists of an 8 mm crank-offset which is an optimized value to have the lowest piston side forces. The honing specification is changed from a standard plateau honing to an improved torque plate slide honing with optimized surface finish values. The cumulative tangential force of the piston rings is reduced to an extreme value of 28.5 N. A rectangular special coated top ring and a low-friction architecture oil ring are used to reduce the friction without increasing the blow-by and oil consumption. A special low-friction coating is applied on the piston skirt in addition to the optimized skirt profile to have reduced contact pressure. The piston pin is coated with diamond-like carbon (DLC) coating to have the lowest friction.

Hydraulic power train assembly of an agricultural tractor is meant to controls the position and draft of the implement depending upon the type of crop, farming stage, implement type and soil conditions. These variations induce extreme range of loads on the hydraulic system, thus making it challenging to design these components. Hydraulic connecting rod is critical component of hydraulic power train assembly. Standards like IS12224, IS4468 governs the design of hydraulic power train components which regulates the test method for hydraulic power and lift capacity of the tractor. In this paper, a virtual simulation process has been established to design a hydraulic connecting rod to meet the requirements. The hydraulic connecting rod basically functions as a short load transferring link, which is subjected to the operating hydraulic pressure of the hydraulic lifting mechanism. The current circular connecting rod is higher in weight and cost.

In driving, Steering is the input motion to the vehicle. The driver uses steering input to change the direction of the vehicle. During Parking or U turn bends the Steering is locked and later released to follow the desired path. Steering return ability is defined as the ratio of difference between steering wheel position at lock condition and steering wheel angle after 3 seconds of release to the steering wheel angle at lock condition. Having proper steering return ability characteristics has an important effect on vehicle steering characteristics. In this study, a full vehicle ADAMS model is prepared, and virtual steering return ability have been simulated in ADAMS/CAR for a Pickup truck vehicle. Simulated responses in the steering wheel angle have been validated by comparison with measurements. A Design of Experiment study is setup and Iterations are carried out to find the effect of Hard points and friction parameters.