Search Results

A 1200-V, 600-A silicon carbide (SiC) JFET half-bridge module has been developed for drop-in replacement of a 600-V, 600-A IGBT intelligent power module (IPM). Advances in the development of SiC field effect transistors have resulted in reliable high yield devices that can be paralleled and packaged to produce high-voltage and high-current power modules not only competitive with existing IGBT technology but the modules have expanded capabilities. A SiC vertical junction field effect transistor VJFET has been produced with the properties of lower conduction loss, zero tail current, higher thermal conductivity, and higher power density when compared to a similarly rated silicon IGBT or any practical SiC MOSFETs previously reported. Three prototype SiC JFET half-bridge modules with gate drivers have been successfully integrated into a three-phase 30-kW (continuous), 100-kW (intermittent) AC synchronous motor drive designed to control a traction motor in an electric vehicle.

A full-system, end-to-end blast modeling and simulation of vehicle underbody buried blast events typically includes detailed modeling of soil, high explosive (HE) charge and air. The complex computations involved in these simulations take days to just capture the initial 50-millisecond blast-off phase, and in some cases, even weeks. The single most intricate step in the buried blast event simulation is in the modeling of the explosive loading on the underbody structure from the blast products; it is also one of the most computationally expensive steps of the simulation. Therefore, there is significant interest in the modeling and simulation community to develop various methodologies for fast running tools to run full simulation events in quicker turnarounds of time.

This paper outlines the process by which a current production commercial diesel engine was modified for high performance military use. Salient among the needs for military use are a compact package and high power output. The compact engine package was addressed by the selection of a base engine of relatively small displacement and slim inline configuration. The air system, fuel pump, and other ancillary components were re-packaged close to the engine. A high engine power output was achieved by turbocharging at the pressure ratios achievable by current production turbochargers, increased engine speed, and upgrades in the design of engine components. Close attention was paid to thermal and mechanical loading of all components of the engine. Most components in the engine were changed to accommodate these loadings and packaging needs.

Improved propulsion system cooling remains an important challenge in the transportation industry as heat generating components, embedded in ground vehicles, trend toward higher heat fluxes and power requirements. The further minimization of the thermal management system power consumption necessitates the integration of parallel heat rejection strategies to maintain prescribed temperature limits. When properly designed, the cooling solution will offer lower noise, weight, and total volume while improving system durability, reliability, and power efficiency. This study investigates the integration of high thermal conductivity (HTC) materials, carbon fibers, and heat pipes with conventional liquid cooling to create a hybrid “thermal bus” to move the thermal energy from the heat source(s) to the ambient surroundings. The innovative design can transfer heat between the separated heat source(s) and heat sink(s) without sensitivity to gravity.

We propose a new metamodeling method to characterize the output (response) random process of a dynamic system with random parameters, excited by input random processes. The metamodel can be then used to efficiently estimate the time-dependent reliability of a dynamic system using analytical or simulation-based methods. The metamodel is constructed by decomposing the input random processes using principal components or wavelets and then using a few simulations to estimate the distributions of the decomposition coefficients. A similar decomposition is also performed on the output random process. A kriging model is then established between the input and output decomposition coefficients and subsequently used to quantify the output random process corresponding to a realization of the input random parameters and random processes. What distinguishes our approach from others in metamodeling is that the system input is not deterministic but random.

Assessing the dynamic performance of multilayer plates subjected to impulsive loading is of interest for identifying configurations that either absorb energy or transmit the energy in the transverse directions, thereby mitigating the through-thickness energy propagation. A reduced-order modeling approach is presented in this paper for rapidly evaluating the structural dynamic performance of various multilayer plate designs. The new approach is based on the reverberation matrix method (RMM) with the theory of generalized rays for fast analysis of the structural dynamic characteristics of multilayer plates. In the RMM model, the waves radiated from the dynamic load are reflected and refracted at each interface between layers, and the waves within each layer are transmitted with a phase lag. These two phenomena are represented by the global scattering matrix and the global phase matrix, respectively.

Understanding reliability is critical in design, maintenance and durability analysis of engineering systems. A reliability simulation methodology is presented in this paper for vehicle fleets using limited data. The method can be used to estimate the reliability of non-repairable as well as repairable systems. It can optimally allocate, based on a target system reliability, individual component reliabilities using a multi-objective optimization algorithm. The algorithm establishes a Pareto front that can be used for optimal tradeoff between reliability and the associated cost. The method uses Monte Carlo simulation to estimate the system failure rate and reliability as a function of time. The probability density functions (PDF) of the time between failures for all components of the system are estimated using either limited data or a user-supplied MTBF (mean time between failures) and its coefficient of variation.

In recent years the U.S. Army Tank-Automotive Research, Development, and Engineering Center (TARDEC) has been investigating the survivability and injury mechanisms of underbody blast and crash, and their effects on personnel, with the use of Anthropomorphic Test Devices (ATD), or crash test dummies. Injury Assessment Reference Values (IARV) for crash have been researched for decades, and the US Army Research Laboratory (ARL), some years ago, also developed IARVs for underbody blast for the Hybrid III 50th percentile ATD. More recently, TARDEC extended these IARVs for the 5th and 95th percentile. With the advent of TARDEC’s Occupant Protection Laboratory large amounts of data were accumulated, which brought an interest in automating the analysis, and so a software tool was developed. The interactive in-house written software, called ICalc, allows the user to open test data files acquired from blast testing, drop tower testing, and crash testing.

Designing an efficient cooling system with low power consumption is of high interest in the automotive engineering community. Heat generated due to the propulsion system and the on-board electronics in ground vehicles must be dissipated to avoid exceeding component temperature limits. In addition, proper thermal management will offer improved system durability and efficiency while providing a flexible, modular, and reduced weight structure. Traditional cooling systems are effective but they typically require high energy consumption which provides motivation for a paradigm shift. This study will examine the integration of passive heat rejection pathways in ground vehicle cooling systems using a “thermal bus”. Potential solutions include heat pipes and composite fibers with high thermal properties and light weight properties to move heat from the source to ambient surroundings.

The current reliability growth planning model used by the US Army, the Planning Model for Projection Methodology (PM2), is insufficient for the needs of the Army. This paper will detail the limitations of PM2 that cause Army programs to develop reliability growth plans that incorporate unrealistic assumptions and often demand that infeasible levels of reliability be achieved. In addition to this, another reliability growth planning model being developed to address some of these limitations, the Bayesian Continuous Planning Model (BCPM), will be discussed along with its own limitations. This paper will also cover a third reliability growth planning model that is being developed which incorporates the advantageous features of PM2 and BCPM but replaces the unrealistic assumptions with more realistic and customizable ones.

Using the total probability theorem, we propose a method to calculate the failure rate of a linear vibratory system with random parameters excited by stationary Gaussian processes. The response of such a system is non-stationary because of the randomness of the input parameters. A space-filling design, such as optimal symmetric Latin hypercube sampling or maximin, is first used to sample the input parameter space. For each design point, the output process is stationary and Gaussian. We present two approaches to calculate the corresponding conditional probability of failure. A Kriging metamodel is then created between the input parameters and the output conditional probabilities allowing us to estimate the conditional probabilities for any set of input parameters. The total probability theorem is finally applied to calculate the time-dependent probability of failure and the failure rate of the dynamic system. The proposed method is demonstrated using a vibratory system.

Enhanced electric motor performance in transportation vehicles can improve system reliability and durability over rigorous operating cycles. The design of innovative heat rejection strategies in electric motors can minimize cooling power consumption and associated noise generation while offering configuration flexibility. This study investigates an innovative electric motor cooling strategy through bench top thermal testing on an emulated electric motor. The system design includes passive (e.g., heat pipes) cooling as the primary heat rejection pathway with supplemental conventional cooling using a variable speed coolant pump and radiator fan(s). The integrated thermal structure, “cradle”, transfers heat from the motor shell towards an end plate for heat dissipation to the ambient surroundings or transmission to an external thermal bus to remote heat exchanger.

An approach is being pursued for a series hybrid electric vehicle (SHEV). The twin goals of maximizing Fuel Economy (FE) and improving consumer acceptance has led to a SHEV powertrain using energy storage as a means for filtering drive cycle power demands on the engine, rather than an energy source for supplying all-electric mode. The concept is intended to minimize, if not eliminate, the battery in the SHEV without resorting to full range proportional control of the engine and generator. An initial optimization study reported for a mid-size SHEV showed a 4.5 kWh Li-ion battery pack was still required. In a new research, a sports car class SHEV was studied, which inspires this manuscript. The challenge with this vehicle is to reduce the ESS size even more because the available space allocation is only one fourth of the battery size in the mid-size. In this manuscript, a controller is developed that allows a hybridized SHEV to be realized with a light ESS.

Hybrid electric vehicles offer the advantages of reduced emissions and greater travel range in comparison to conventional and electric ground vehicles. Regardless of propulsion strategy, efficient cooling of electric motors remains an open challenge due to the operating cycles and ambient conditions. The onboard thermal management system must remove the generated heat so that the motors and other vehicle components operate within their designed temperature ranges. In this article, an integrated thermal structure, or cradle, is designed to efficiently transfer heat within the motor housing to the end plates for transmission to an external heat exchanger. A radial array of heat pipes function as an efficient thermal connector between the motor and heat connector, or thermal bus, depending on the configuration. Cooling performance has been evaluated for various driving cycles.

It is of considerable interest to developers of military vehicles, in early phases of the concept design process as well as in Analysis of Alternatives (AoA) phase, to quickly predict occupant injury risk due to under-body blast loading. The most common occupant injuries in these extremely short duration events arise out of the very high vertical acceleration of vehicle due to its close proximity to hot high pressure gases from the blast. In a prior study [16], an extensive parametric study was conducted in a systematic manner so as to create look-up tables or automated software tools that decision-makers can use to quickly estimate the different injury responses for both stroking and non-stroking seat systems in terms of a suitable blast load parameter. The primary objective of this paper is to quantitatively evaluate the accuracy of using such a tool in lieu of building a detailed model for simulation and occupant injury assessment.

The NATO Reference Mobility Model (NRMM)[1] is the primary mobility software used by the US Department of Defense, its contractors and NATO countries to evaluate various metrics of proposed vehicle systems for acquisition. The NRMM is a vehicle mobility performance model developed in the 1970's[2] that combines mobility related technologies into one comprehensive software package designed to predict the physically constrained vehicle and terrain interaction while operating in both on and off road environments. The empirically based relationships within NRMM are measurements taken from actual vehicles run over a variety of terrains and are geared towards vehicles weighing more than 1500 pounds. As the Army focuses on a lighter, faster and more mobile fighting force, standard military vehicles are decreasing in size with many newultra lightweight autonomous systems being designed.

Military vehicles are typically armored, hence the open surface area for heat rejection is limited. Hence, the cooling parasitic load for a given heat rejection can be considerably higher and important to consider upfront in the system design. Since PEMFCs operate at low temp, the required cooling flow is larger to account for the smaller delta temperature to the air. This research aims to address the combined problem of optimal sizing of the lithium ion battery and PEM Fuel Cell stack along with development of the scalable power split strategy for small a PackBot robot. We will apply scalable physics-based models of the fuel cell stack and balance of plant that includes a realistic and scalable parasitic load from cooling integrated with existing scalable models of the lithium ion battery. This model allows the combined optimization that captures the dominant trends relevant to component sizing and system performance.

Variability in design (e.g. tolerance), material, manufacturing, or other sources of variation causes significant variation in vehicle noise, vibration and harshness (NVH) response. This leads to a higher percentage of produced vehicles with higher levels of NVH leading to higher number of warranty claims and loss of customer satisfaction, which are proven costly to the original equipment manufacturers (OEM). Measures must be taken to insure less warranty claims and higher levels of customer satisfaction. As a result, original equipment manufacturers have implemented design for variation in the design process to secure an acceptable (or within specification) response. We will focus on some aspects of design variations in a tire/wheel assembly that should be considered in the design process. In particular, certain materials (e.g. rubber) are known to have variation in stiffness that is either unavoidable or proven costly if tighter control is desired.

This paper describes the author's experiences in the design, validation and field-testing of a low cost, online oil condition monitor for diesel driven Army ground vehicles. This online oil condition monitor utilizes a multi-frequency approach to electrochemical impedance spectroscopy to interrogate and evaluate fluid health in near real time. A dual microcontroller processing architecture embedded in the sensor itself executes an oil-health evaluation algorithm and provides estimates of lubricant remaining useful life, as well as identification of the primary mode of degradation of the fluid. These data are transmitted off the sensor via J1939 compliant CAN messages. In this paper the unique application requirements, which formed the foundation of the development process, are discussed, and the technical and design challenges associated with producing a military grade smart-sensor at a sufficiently low price point for widespread adoption in the ground vehicle market are detailed.

A dynamic modeling framework was established to predict status (position, displacement, velocity, acceleration, and shape) of a towed vehicle system with different driver inputs. This framework consists of three components: (1) a state space model to decide position and velocity for the vehicle system based on Newton’s second law; (2) an angular acceleration transferring model, which leads to a hypothesis that the each towed unit follows the same path as the towing vehicle; and (3) a polygon model to draw instantaneous polygons to envelop the entire system at any time point. Input parameters of this model include initial conditions of the system, real-time locations of a reference point (e.g. front center of the towing vehicle) that can be determined from a beacon and radar system, and instantaneous accelerations of this system, which come from driver maneuvers (accelerating, braking, steering, etc.) can be read from a data acquisition system installed on the towing vehicle.