Search Results

The fuel consumption and emissions of diesel engines is strongly influenced by the injection rate pattern, which influences the in-cylinder mixing and combustion process. Knowing the exact injection rate is mandatory for an optimal diesel combustion development. The short injection time of no more than some milliseconds prevents a direct flow rate measurement. However, the injection rate is deduced from the pressure change caused by injecting into a fuel reservoir or pipe. In an ideal case, the pressure increase in a fuel pipe correlates with the flow rate. Unfortunately, real measurement devices show measurement inaccuracies and errors, caused by non-ideal geometrical shapes as well as variable fuel temperature and fuel properties along the measurement pipe. To analyze the thermal effect onto the measurement results, an available rate measurement device is extended with a flexible heating system as well as multiple pressure and temperature sensors.

The Ford GT powertrain (see Figure 1) is an integrated system developed to preserve the heritage of the LeMans winning car of the past. A team of co-located engineers set out to establish a system that could achieve this result for today's supercar. Multiple variations of engines, transaxles, cooling systems, component locations and innovations were analyzed to meet the project objectives. This paper covers the results and achievements of that team.

A study was conducted using Ford's nine standard CFD calibration models as described in SAE paper 940323. The models are identical from the B-pillar forward but have different back end configurations. These models were created for the purpose of evaluating the effect of back end geometry variations on aerodynamic lift and drag. Detailed experimental data is available for each model in the form of surface pressure data, surface flow visualization, and wake flow field measurements in addition to aerodynamic lift and drag values. This data is extremely useful in analyzing the accuracy of the numerical simulations. The objective of this study was to determine the capability of a digital physics based commercial CFD code, PowerFLOW ® to accurately simulate the physics of the flow field around the car-like benchmark shapes.

Software development for automotive application requires several iterations in order to tune parameters and strategy logic to operate accordantly with optimal performance. Thus, in this paper we present an optimizer method and tool used to tune calibration parameters related to torque estimation for a hybrid automatic transmission application. This optimizer aims to minimize the time invested during the software calibration and software development phases that could take significant time in order to cover the different driving conditions under which a hybrid automatic transmission can operate. For this reason, an optimization function based on the Nelder-Mead simplex algorithm using Matlab software helps to find optimized calibration values based on a cost function (square sum error minimization).

Combustion in modern spark-ignition (SI) engines is increasingly knock-limited with the wide adoption of downsizing and turbocharging technologies. Fuel autoignition conditions are different in these engines compared to the standard Research Octane Number (RON) and Motor Octane Numbers (MON) tests. The Octane Index, OI = RON - K(RON-MON), has been proposed as a means to characterize the actual fuel anti-knock performance in modern engines. The K-factor, by definition equal to 0 and 1 for the RON and MON tests respectively, is intended to characterize the deviation of modern engine operation from these standard octane tests. Accurate knowledge of K is of central importance to the OI model; however, a single method for determining K has not been well accepted in the literature.

As part of the International Lubricant Standardization and Approval Committee's (ILSAC) goal of developing a global automatic transmission fluid (ATF) specification, members have been evaluating test methods that are currently used by various automotive manufacturers for qualifying ATF for use in their respective transmissions. This report deals with comparing test methods used for determining torque capacity in friction systems (shifting clutches). Three test methods were compared, the Plate Friction Test from the General Motors DEXRON®-III Specification, the Friction Durability Test from the Ford MERCON® Specification, and the Japanese Automotive Manufacturers Association Friction Test - JASO Method 348-95. Eight different fluids were evaluated. Friction parameters used in the comparison were breakaway friction, dynamic friction torque at midpoint and the end of engagement, and the ratio of end torque to midpoint torque.

In a recent study, quantitative measurements were presented of in-cylinder spatial distributions of mixture equivalence ratio in a single-cylinder light-duty optical diesel engine, operated with a non-reactive mixture at conditions similar to an early injection low-temperature combustion mode. In the experiments a planar laser-induced fluorescence (PLIF) methodology was used to obtain local mixture equivalence ratio values based on a diesel fuel surrogate (75% n-heptane, 25% iso-octane), with a small fraction of toluene as fluorescing tracer (0.5% by mass). Significant changes in the mixture's structure and composition at the walls were observed due to increased charge motion at high swirl and injection pressure levels. This suggested a non-negligible impact on wall heat transfer and, ultimately, on efficiency and engine-out emissions.

This paper describes the relationship between the design parameters used to define the geometry of an automotive torque converter and the resultant efficiency in relation to the internal flow characteristics. Taking the turbine bias angle and the contraction ratio of the pump flow passage as specific examples, the effects of each design parameter on the internal flow characteristics and the occurrence of loss were analyzed. A three-dimensional viscous flow analysis code was used in the numerical computation procedure and a method developed independently by the authors was used in the loss analysis. The flow near the wall was visualized experimentally using a technique resembling the so-called oil film method. The visualized results showed good qualitative agreement with the numerical analysis results.

Designing a durability test for an automatic transmission that appropriately reflects customer usage during the lifetime of the vehicle is a formidable task; while the transmission and its components must survive severe usage, overdesigning components leads to unnecessary weight, increased fuel consumption and increased emissions. Damage to transmission components is a function of many parameters including customer driving habits and vehicle and transmission characteristics such as weight, powertrain calibration, and gear ratios. Additionally, in some cases durability tests are required to verify only a subset of the total parameter space, for example, verifying only component modifications. Lastly, the ideal durability test is designed to impose the worst case loading conditions for the maximum number of internal components, be as short as practicable to reduce testing time, with minimal variability between tests in order to optimize test equipment and personnel resources.

A method of predicting brake specific fuel consumption characteristics from limited specifications of engine design has been investigated. For spark ignition engines operating on homogeneous mixtures, indicated specific fuel consumption based on gross indicated power is related to compression ratio and spark timing relative to optimum values. The influence of burn rate is approximately accounted for by the differences in spark timings required to correctly phase combustion. Data from engines of contemporary design shows that indicated specific fuel consumption can be defined as a generic function of relative spark timing, mixture air/fuel ratio and exhaust gas recirculation rate. The additional information required to generate brake specific performance maps is cylinder volumetric efficiency, rubbing friction, auxiliary loads, and exhaust back pressure characteristics.

A dynamic powertrain system model of the High Mobility Multi-Wheeled Vehicle (HMMWV) was created in the Powertrain Control Research Laboratory (PCRL) at the University of Wisconsin-Madison. Simulink graphical programming software was used to create the model. This dynamic model includes a Torsen differential model and a Hyrda-matic 4L80-E automatic transmission model as well as several other powertrain component models developed in the PCRL. Several component inertias and shaft stiffnesses are included in the dynamic model. The concepts of modularity, flexibility, and user-friendliness were emphasized during model development so that the system model would be a useful design tool. Simulation results from the model are shown.

NVH problems are often the result of mechanisms that originate through complex interactions between different physical domains (flow, structural/mechanical, control logic, etc.). Parallel-shaft spur gears subject to light torque loading caused by the dynamic pressure fluctuation of the oil used in engine accessory or transmission pump drives are likely to exhibit unusual gear whine associated with higher order meshing harmonics, even when the tooth profile has a high-quality grade finishing. Therefore, accurate integrated models are becoming a requirement to solve modern NVH problems.

In order to improve fuel economy, engine manufacturers are investigating various technologies that reduce pumping work in spark ignition engines. Current cylinder pressure analysis methods do not allow valid comparison of pumping work reduction strategies. Existing methods neglect valve timing effects which occur during the expansion and compression strokes, but are actually part of the gas exchange process. These additional pumping work contributions become more significant when evaluating non-standard valve timing concepts. This paper outlines a new analysis method for calculating the pumping work and indicated work of a 4-stroke internal combustion engine. Corrections to PMEP and IMEP are introduced which allow the valid comparison of pumping work and indicated efficiency between engines with different pumping work reduction strategies.

A flatter design is becoming increasingly important for reducing torque converter axial size and weight. The conventional stator design method, in which the blade profile is geometrically determined and flow analysis of the profile may give some valuable information, is no longer sufficient for achieving efficient flow turning in the short axial length of flat torque converters. Here, after a brief review of the conventional design approach, an inverse design method is introduced, which yields a blade profile solution for a prescribed favorable velocity distribution along the blade. The performance improvement with this procedure has been demonstrated experimentally.

There has been a growing need to develop more compact automatic transmissions with a greater number of speeds for better fuel economy and better driveability. This study investigated a method for determining suitable planetary gear trains for today's transmissions. A computer program has been developed for application to five-speed transmissions consisting of two planetary gearsets. By analyzing various gear train possibilities, the program can identify which gearsets are suitable for different conditions, including the number of speeds, the number of binding elements, topological suitability and other factors.

An electronically controlled five-speed automatic transmission has been developed for use in new 2-liter models. This high-performance gearbox is the world's first five-speed automatic transmission for passenger car use to be equipped with a torque converter. It is designed with an ultra-wide range and close ratio gearing and incorporates a host of outstanding technologies to provide excellent performance and driveability. This paper describes the major features and performance of this new automatic transmission and some of the studies undertaken concerning multiplication of gear steps.

Automatic transmission gear changes are transient disturbances in a non-linear system, during which the effective ratio of the transmission is continually changing. In addition, vehicle characteristics can very strongly influence customer perception of the shift event. Further, the interface elements between the vehicle and powertrain are often crucial in determining the quality of shift feel. This paper presents a validated CAE method that employs the ADAMS software to predict the intricate dynamics of the vehicle response due to transmission shift events. First principles of the transmission modeling elements are described. Model simulation results are compared to vehicle test data. A method to quantify the customer's perception of vehicle shift quality is discussed. Model simulation results for a FWD vehicle application are also analyzed.

There is keen interest in understanding the origins of engine-out unburned hydrocarbons emitted during SI engine cold start. This is especially true for the first few firing cycles, which can contribute disproportionately to the total emissions measured over standard drive cycles such as the US Federal Test Procedure (FTP). This study reports on the development of a novel methodology for capturing and quantifying unburned hydrocarbon emissions (HC), CO, and CO2 on a cycle-by-cycle basis during an engine cold start. The method was demonstrated by applying it to a 4 cylinder 2 liter GTDI (Gasoline Turbocharged Direct Injection) engine for cold start conditions at an ambient temperature of 22°C. For this technique, the entirety of the engine exhaust gas was captured for a predetermined number of firing cycles.

Transmission system models require a high level of fidelity and details in order to capture the transient behaviors in drivability and fuel economy simulations. Due to model fidelity, manufacturing tolerances, frictional losses and other noise sources, parametrization and tuning of a large number of parameters in the plant model is very challenging and time consuming. In this paper, we used particle swarm optimization as the key algorithm to fast correlate the open-loop performance of an automatic transmission system plant model to vehicle launch and coast down test data using vehicle control inputs. During normal operations, the model correlated well with test data. For error states, due to the lack of model fidelity, the model cannot reproduce the same error state quantitatively, but provided a valuable methodology for qualitatively identifying error states at the early stages.