Search Results

Conventional power steering systems can be “tailored” to provide light steering efforts for parking and low speed, or high steering efforts for stability and “road feel” at high speed. In either case, the customer's preferred steering efforts are not provided at all times. Compromises are required. The need for a speed-sensitive steering effort system has prompted the introduction of several innovative variable-assist steering systems in the past few years, which are currently used in some European and Japanese vehicles. This paper describes a Ford-patented variable-assist system used on the 1988 Lincoln Continental, the first application of vehicle speed-sensitive steering to an American-designed and manufactured vehicle. The Ford Variable-Assist Power Steering System is a “rotary steering valve” system. It uses a modification of the current rotary valve to provide low steering efforts (low torsion bar twist) at low speed and higher efforts (more twist) as vehicle speed increases.

This paper reports on the injuries to the head, neck and thorax of fifteen child surrogates, subjected to varying levels of sudden acceleration. Measured response data in the child surrogate tests and in matched tests with a three-year-old child test dummy are compared to the observed child surrogates injury levels to develop preliminary tolerance data for the child surrogate. The data are compared with already published data in the literature.

The cyclic behavior of single overlap aluminum joints joined through a number of different methods has been investigated using Alcan 5754-O, an alloy that potentially could be used in structural applications. Overlap shear tests of spot welded, clinched and riveted joints are compared on the basis of their fatigue performance. The fatigue response of the spot welded joint was the baseline to which the other fasteners were compared. Test results showed an improvement of approximately 25% for both the mechanical clinch joints and aluminum rivets in fatigue strength at 106 cycles. The most significant improvement in fatigue strength of 100% was found for the self piercing rivets at 106 cycles. The failure behavior of the various joining methods is discussed as well as the surface appearance.

This paper reports the analytical procedure developed for a simulation of knee impact during a barrier crash using a hybrid III dummy lower torso. A finite element model of the instrument panel was generated. The dummy was seated in mid-seat position and was imparted an initial velocity so that the knee velocity at impact corresponded to the secondary impact velocity during a barrier crash. The procedure provided a reasonably accurate simulation of the dummy kinematics. This simulation can be used for understanding the knee bolster energy management system. The methodology developed has been used to simulate impact on knee for an occupant belted or unbelted in a frontal crash. The influence of the vehicle interior on both the dummy kinematics and the impact locations was incorporated into the model. No assumptions have been made for the knee impact locations, eliminating the need to assume knee velocity vectors.

Vehicle sound quality has become an important basic performance requirement. Traditionally, automobile noise studies were focused on quietness. It is now necessary for the automobile to be more than quiet. The sound must be pleasing. This paper describes a development process to improve both vehicle noise level and sound quality. Formal experimental design techniques were utilized to quantify various hardware effects. A-weighted sound pressure level, Speech Intelligibility, and Composite Rating of Preference were the three descriptors used to characterize the vehicle's sound quality. Engineering knowledge augmented with graphical and statistical techniques were utilized during data analysis. The individual component contributions to each of the sound quality descriptors were also quantified in this study.

A four-stroke, spark-ignition engine is described that seeks to achieve high expansion ratio and low throttling losses at light load, whilst retaining good knock resistance at full load operation and without the need for expensive mechanical changes to the engine. The engine does, however, incorporate a second inlet (transfer) valve and associated transfer port linked to the intake port. The timing of the transfer valve is different from that of the main inlet valve. Load modulation is achieved by control of the gas outflow from the transfer port. A computer model of the engine is first validated against measured data from a conventional engine. Comparisons are made of incylinder pressure at part load conditions, total air flowrate through the engine and intake port air velocities as a function of crank angle position.

A hybrid approach to predict road-induced loads in vehicle structures is presented. The technique involves full vehicle dynamic simulation using measured wheel forces, absolute wheel vertical displacements, and steering angle as input. The wheel vertical displacement is derived from the measured wheel acceleration. This approach avoids the use of tire-road interface modeling. It also improves the conventional loads measuring process with minimum instrumentation and data acquisition. Existing load data from a test vehicle is used to validate this approach. Computed component loads show good agreement with measurements.

There have been many articles published in the last decade or so concerning the components of an electronic stability control (ESC) system, as well as numerous statistical studies that attempt to predict the effectiveness of such systems relative to crash involvement. The literature however is free from papers that discuss how engineers might develop such systems in order to achieve desired steering, handling, and stability performance. This task is complicated by the fact that stability control systems are very complex and their designs and what they can do have changed considerably over the years. These systems also differ from manufacturer to manufacturer and from vehicle to vehicle in a given maker of automobiles. In terms of ESC hardware, differences can include all the components as well as the addition or absence of roll rate sensors or active steering gears to name a few.

European legislation covering noise, smoke emission and industrial pollution, all seeking to improve the environment are not addressed in this paper, which takes only exhaust emission and fuel complexity as its subjects. It describes how this complexity can inhibit the development capacity, thus restricting the model offering of a major european automobile manufacturer. The paper concludes that general benefit would be derived from genuine pan european emission legislation, particularly if that legislation was established at levels of control that allowed the development and use of modern engine technology.

Significant progress could not have been made in the Sound Quality area without the invention and development of engineering tools. For the sound engineer, the binaural recording head is a primary example of one of those tools. The use of the binaural recording head was crucial to the development of the sound characterization process and has become an essential tool in the Sound Quality areas in Ford Motor Company. A similar tool, The Ford Vehicle Vibration Simulator, has been developed for the vibration engineer. The vehicle vibration simulator (VVS) is unique, consisting of vibration of the vehicle seat (6 degrees of freedom), steering wheel (4 DOF), vehicle floorpan section (1 DOF), and the brake or accelerator pedal (1 DOF). Many vibration test systems have been developed to study human response to vibration, especially for military and space applications. To our knowledge, this is the first multi-axis, fully integrated vibration test system to be used for automotive applications.

This paper presents a new transient passenger thermal comfort model. The model uses as inputs the vehicle environmental variables: air temperature, air velocity, relative humidity and mean radiant temperature all of which can vary as a function of time and space. The model also uses as inputs the clothing level and the initial physiological state of the body. The model then predicts as a function of time the physiological state of the body and an effective human thermal sensation response (e.g. cold, comfort, hot, etc.). The advantage of this model is that it can accurately predict the human thermal sensation response during transient vehicle warm-up and cooldown conditions. It also allows design engineers the ability to conduct parametric studies of climate control systems before hardware is available. Here we present the basis of the new thermal comfort model and its predictions for transient warm-up and cooldown conditions.

The pumping system used in a step ratio automatic transmission can consume up to 20% of the total power required to operate a typical automotive transmission through the EPA city cycle. As such, it represents an area manufacturers have focused their efforts towards in their quest to obtain improved transmission efficiency. This paper will discuss the history of automatic transmission pumps that develop up to 300 psi along with a description of the factors used to size pumps and establish pump flow requirements. The various types of pumps used in current automatic transmissions will be described with a discussion of their characteristics including a comparison based upon observations of their performance. Specific attention will be focused on comparing the volumetric efficiency, mechanical efficiency, overall efficiency, pumping torque and discharge flow.

A feedgas hydrocarbon emissions model that extends the usefulness of fully-warmed steady-state engine maps to the cold transient regime was developed for use within a vehicle simulation program that focuses on the powertrain control system (Virtual Powertrain and Control System, VPACS). The formulation considers three main sources of hydrocarbon. The primary component originates from in-cylinder crevice effects which are correlated with engine coolant temperature. The second component includes the mass of fuel that enters the cylinder but remains unavailable for combustion (liquid phase) and subsequently vaporizes during the exhaust portion of the cycle. The third component includes any fuel that remains from a slow or incomplete burn as predicted by a crank angle resolved combustion model.

The present work discusses an objective test and analysis method developed to quickly quantify steering gear rattle noise heard in a vehicle. Utilizing envelope analysis on the time history data of the rattle signal, the resulting method is simple, fast, practical and yields a single-valued metric which correlates well to subjective measures of rattle noise. In contrast to many other rattle analysis methods, the approach discussed here is completed in the time domain. As applied to rattle noise produced by automotive electric steering systems, the metric produced with this analysis method correlates well with subjective appraisals of vehicle-level rattle noise performance. Lastly, this method can also be extended to rattle measurements at the component and subcomponent level.

Ribbed floor panels have been widely applied in vehicle body structures to reduce interior noise. The conventional approach to evaluate ribbed floor panel designs is to compare natural frequencies and local stiffness. However, this approach may not result in the desired outcome of the reduction in radiated noise. Designing a “quiet” floor panel requires minimizing the total radiated noise resulting from vibration of the floor panel. In this study, the objective of ribbed floor panel design is to reduce the total radiated sound power by optimizing the rib patterns. A parametric study was conducted first to understand the effects of rib design parameters such as rib height, width, orientation, and density. Next, a finite element model of a simplified body structure with ribbed floor panel was built and analyzed. The structural vibration profile was generated using MSCINastran, and integrated with the acoustic boundary element model.

Model characteristics of a finite element deformable featureless headform with one to four layers of solid elements for the headform skin are studied using both the LS-DYNA3D and FCRASH codes. The models use a viscoelastic material law whose constitutive parameters are established through comparisons of drop test simulations at various impact velocities with the test data. Results indicate that the one-layer model has a significant distinct characteristic from the other (2-to-4-layer) models, thus requiring different parametric values. Similar observation is also noticed in simulating drop tests with one and two layers of solid elements for the headform skin using PAM-CRASH. When using the same parametric values for the viscoelastic material, both the LS-DYNA3D and FCRASH simulations yield the same results under identical impact conditions and, thereby, exhibit a “functional equivalency” between these two codes.

In this paper we describe the application of optimization techniques to the design of valvetrains in high revving internal combustion engines. The methods presented are based on parameter optimization [1] and the minimum principle by Pontrjagin [2] and will be applied to cam lobe and valve spring optimization, aiming at reducing oscillation amplitudes and improving control of the valvetrain over a broad speed range. To put the task of optimization into context the engineering requirements for valvetrains and methods to allow their computer based analysis are described. Furthermore principle considerations for valve event curve generation and parametrization, and on optimization techniques are discussed. Based on these fundamentals, optimization aims and constraints are formulated. Furthermore different examples of the application of automated optimization are presented in the area of cam profile optimization and valve spring optimization.

A number of advancements have been made in the coulometric sulfur trace instrumental technique for the real-time measurement of engine oil economy. These advancements include modification of the coulometric cell to improve reliability and reproducibility. The instrument has been interfaced with a microcomputer for instrument control as well as data acquisition, storage, and analysis. Studies were undertaken which demonstrate sufficient sensitivity and linearity for determination of engine oil economy at levels better than 10,000 miles/quart. Applications to steady-state engine oil consumption mapping and to instantaneous oil consumption during transient engine cycling are described. These instruments are being produced by an outside supplier for use in various company locations in both the engine production and engine research environments.

The long term visual appearance of exterior chrome-plated parts is highly dependent on part design and supplier performance. The use of numerous complex designs coupled with the pressures of competition has caused a statistically high percentage of parts to be manufactured which do not fully meet customer expectations. A coordinated approach to improve supplier performance and simplification of part designs was required. A task force was established to address these issues in 1980 and desirable results were achieved.

The thermal comfort of passengers within a vehicle is often the main objective for the climate control engineer; however, the need to maintain adequate visibility through the front and side windows of a vehicle is a critical aspect of safe driving. This paper compares the performance of the side window defrosting and demisting mechanism of several current model vehicles. The study highlights the drawbacks of current designs and points the way to improved passive defrosting mechanisms. The investigation is experimental and computational. The experiments are carried out using full-scale current vehicle models. The computational study, which is validated by the experiments, is used to perform parametric investigation into the side window defrosters performance. The results show that the current designs of the side-defroster nozzles give maximum airflow rates in the vicinity of the lower part of the window, which yields unsatisfactory visibility.