Search Results

The objective of this work is to better understand freezing fog/drizzle conditions using observations collected during the Fog Remote Sensing and Modeling project (FRAM-S) that took place at St. John's International Airport, St. John's, NL, Canada. This location was ~1 km away from the Atlantic Ocean coast. During the project, the following measurements at one minute resolution were collected: precipitation rate (PR) and amount, fog/drizzle microphysics, 3D wind speed (Uh) and turbulence (Uh'), visibility (Vis), IR and SW radiative fluxes, temperature (T) and relative humidity (RH), and aerosol observations. The reflectivity and microphysical parameters obtained from the Metek Inc. MRR (Microwave Rain Radar) were also used in the analysis. The measurements were then used to obtain freezing fog/drizzle microphysical characteristics and their relation to visibility.

Two high voltage, Series Connected Boost Regulators (SCBR) were developed to demonstrate the benefits of the SCBR topology for low Earth orbit communication satellites. The resulting breadboards had a power density of 1,200 W/kg and a measured efficiency of 95-99%. Several peak power tracking methods and algorithms were implemented to demonstrate the ability of the SCBR to peak power track a solar array. The peak power tracker derived maximum power at all times and reduced the number of sunlight battery discharges necessary. The breadboards also demonstrated several modularity techniques, which will allow a common SCBR module to be used in several applications. The breadboards were tested in an end-to-end high voltage test facility using high fidelity solar array simulators, an actual NiH2 battery, and simulated constant power loads. Design details and test results are presented.

A new optical array imaging probe, called the 1D2D probe, has been developed by Science Engineering Associates, with features added to improve the real-time and post-analysis measurements of particle spectra, particularly in the Supercooled Large Droplet size range. The probe uses optical fibers and avalanche photodiodes to achieve a very high frequency response, and a Field-Programmable Gate Array that performs real-time particle rejection and processing of accepted particles with negligible inter-particle dead time. The probe records monochromatic two-dimensional images, while also recording the number of individual particle pixels at a second grey scale level. The probe implements flexible features to filter recording of highly out of focus particles to improve the accuracy of particle size determination, or to reject small particles to improve the statistics of measurements of larger particles.

Many studies have been performed to quantify the formation and evolution of roughness on ice shapes created in Appendix C icing conditions, which exhibits supercooled liquid droplets ranging from 1-50 µm. For example Anderson and Shin (1997), Anderson et al. (1998), and Shin (1994) represent early studies of ice roughness during short-duration icing events measured in the Icing Research Tunnel at the NASA Glenn Research Center. In the historical literature, image analysis techniques were employed to characterize the roughness. Using multiple images of the roughness elements, these studies of roughness focused on extracting parametric representations of ice roughness elements. While the image analysis approach enabled many insights into icing physics, recent improvements in laser scanning approaches have revolutionized the process of ice accretion shape characterization.

In-flight icing is an important consideration that affects aircraft design, performance, certification and safety. Newer regulations combined with increasing demand to reduce fuel burn, emissions and noise are driving a need for improvements in icing simulation capability. To that end, this paper presents the results of additional ice accretion testing conducted in the NASA Icing Research Tunnel in January 2022 with a large swept wing section typical of a modern commercial transport. The model was based upon a section of the Common Research Model wing at the 64% semispan station with a streamwise chord length of 136 in. The test conditions were developed with an icing scaling analysis to generate similar conditions for a small median volumetric diameter (MVD) = 25 μm cloud and a large MVD = 110 μm cloud. A series of tests were conducted over a range of total temperature from -23.8 °C to -1.4 °C with all other conditions held constant.

Advancements in numerical weather prediction (NWP) models continue to enhance the quality of in-flight icing forecasts and diagnoses. When diagnosing current in-flight icing conditions, observational datasets are combined with NWP model output to form a more accurate representation of those conditions. Surface observations are heavily relied upon to identify cloud coverage and cloud base height above observing stations. One of the major challenges of using these point-based or otherwise limited observations of cloud properties is extending the influence of the observation to nearby points on the model grid. An alternate solution to the current method for incorporating these point-based observations into the in-flight icing diagnoses was developed. The basis for the new method is rooted in a concept borrowed from signal and image processing known as dithering.

An experimental research effort was begun to develop a database of airplane aerodynamic characteristics with simulated ice accretion over a large range of incidence and sideslip angles. Wind-tunnel testing was performed at the NASA Langley 12-ft Low-Speed Wind Tunnel using a 3.5% scale model of the NASA Langley Generic Transport Model. Aerodynamic data were acquired from a six-component force and moment balance in static-model sweeps from α = -5 to 85 deg. and β = -45 to 45 deg. at a Reynolds number of 0.24x10⁶ and Mach number of 0.06. The 3.5% scale GTM was tested in both the clean configuration and with full-span artificial ice shapes attached to the leading edges of the wing, horizontal and vertical tail. Aerodynamic results for the clean airplane configuration compared favorably with similar experiments carried out on a 5.5% scale GTM.

This paper discusses technologies and software tools that are being implemented in a software toolkit currently under development at NASA Glenn Research Center. Its purpose is to help study the effects of icing on airfoil performance and assist with the aerodynamic simulation process which consists of characterization and modeling of ice geometry, application of block topology and grid generation, and flow simulation. Tools and technologies for each task have been carefully chosen based on their contribution to the overall process. For the geometry characterization and modeling, we have chosen an interactive rather than automatic process in order to handle numerous ice shapes. An Appendix presents features of a software toolkit developed to support the interactive process. Approaches taken for the generation of block topology and grids, and flow simulation, though not yet implemented in the software, are discussed with reasons for why particular methods are chosen.

Ice accretions that have formed inside gas turbine engines as a result of flight in clouds of high concentrations of ice crystals in the atmosphere have recently been identified as an aviation safety hazard. NASA's Aviation Safety Program (AvSP) has made plans to conduct research in this area to address the hazard. This paper gives an overview of NASA's engine ice-crystal icing research project plans. Included are the rationale, approach, and details of various aspects of NASA's research.

This paper describes the DC bus regulation control algorithm for the NASA flywheel energy storage system during charge, charge reduction and discharge modes of operation. The algorithm was experimentally verified in [1] and this paper presents the necessary models for simulation. Detailed block diagrams of the controller algorithm are given. It is shown that the flywheel system and the controller can be modeled in three levels of detail depending on the type of analysis required. The three models are explained and then compared using simulation results.

Modifications have been implemented in the GlennICE software to accommodate a non-inertial reference frame. GlennICE accepts a flow solution from an external flow solver. It then introduces particles and tracks them through the flow field in a Lagrangian manner. Centrifugal and Coriolis terms were added to the GlennICE software to account for relative frame simulations. The objective of the present paper is twofold. First, to check that the new terms are implemented correctly and that the code still behaves as expected with respect to convergence. And second, to provide some initial insight into an upcoming propeller experiment in the NASA Icing Research Tunnel. The paper presents a description of the code modifications. In addition, results are presented for two operating conditions, and three particle sizes. Each case was simulated with four different grid densities to assess grid dependence.

NASA Glenn Research Center and the Wallops Flight Facility jointly conducted a PEM fuel cell power system development effort for high altitude balloon applications. This was the first phase of NASA efforts to offer higher balloon payload power levels with extended duration mission capabilities for atmospheric science missions. At present, lead-acid batteries typically supply about 100 watts of power to the balloon payload for approximately 8 hours duration. The H2-O2 PEM fuel cell demonstration system developed for this effort can supply at least 200 watts for 48 hours duration. The system was designed and fabricated, then tested in ambient ground environments as well as in a thermal vacuum chamber to simulate operation at 75 kft. altitude. Initially, this program was planned to culminate with a demonstration flight test but no flight has been scheduled, thus far.

The history and current status of spacecraft smoke detection is discussed including a review of the state of understanding of the effect of gravity on the resultant smoke particle size. The results from a spacecraft experiment (Comparative Soot Diagnostics (CSD)) which measured microgravity smoke particle sizes are presented. Five different materials were tested producing smokes with different properties including solid aerosol smokes and liquid droplets aerosol smokes. The particulate size distribution for the solid particulate smokes increased substantially in microgravity and the results suggested a corresponding increase for the smokes consisting of a liquid aerosol. A planned follow on experiment that will resolve the issues raised by CSD is presented. Early results from this effort have provided the first measurements of the ambient aerosol environment on the ISS (International Space Station) and suggest that the ISS has very low ambient particle levels.

Operational issues encountered by Apollo astronauts relating to lunar dust were catalogued, including material abrasion that resulted in scratches and wear on spacesuit components, ultimately impacting visibility, joint mobility and pressure retention. Standard methods are being developed to measure abrasive wear on candidate construction materials to be used for spacesuits, spacecraft, and robotics. Calibration tests were conducted using a standard diamond stylus scratch tip on the common spacecraft structure aluminum, Al 6061-T6. Custom tips were fabricated from terrestrial counterparts of lunar minerals for scratching Al 6061-T6 and comparing to standard diamond scratches. Considerations are offered for how to apply standards when selecting materials and developing dust mitigation strategies for lunar architecture elements.

NASA and the FAA are funding the development of ground-based remote sensing systems specifically designed to detect and quantify the icing environment aloft. The goal of the NASA activity is to develop a relatively low cost stand-alone system that can provide practical icing information to the flight community. The goal of the FAA activity is to develop more advanced systems that can identify supercooled large drop (SLD) as well as general icing conditions and be integrated into the existing weather information infrastructure. Both activities utilize combinations of sensing technologies including radar, radiometry, and lidar, along with Internet-available external information such as numerical weather model output where it is found to be useful. In all cases the measured data of environment parameters will need to be converted into a measure of icing hazard before it will be of value to the flying community.

Tests designed to quantify the gravitational effects on thermal mixing and reactant injection in a Supercritical Water Oxidation (SCWO) reactor have recently been performed in the Zero Gravity Facility (ZGF) at NASA's Glenn Research Center. An artificial waste stream, comprising aqueous mixtures of methanol, was pressurized to approximately 250 atm and then heated to 450°C. After uniform temperatures in the reactor were verified, a controlled injection of air was initiated through a specially designed injector to simulate diffusion limited reactions typical in most continuous flow reactors. Results from a thermal mapping of the reaction zone in both 1-g and 0-g environments are compared. Additionally, results of a numerical model of the test configuration are presented to illustrate first order effects on reactant mixing and thermal transport in the absence of gravity.

Evaluating real-world hazards associated with perception subsystems is critical in enhancing the performance of autonomous vehicles. The reliability of autonomous vehicles perception subsystems are paramount for safe and efficient operation. While current studies employ different metrics to evaluate perception subsystem failures in autonomous vehicles, there still exists a gap in the development and emphasis on engineering requirements. To address this gap, this study proposes the establishment of engineering requirements that specifically target real-world hazards and resilience factors important to AV operation, using High-Definition Maps, Global Navigation Satellite System, and weather sensors. The findings include the need for engineering requirements to establish clear criteria for a high-definition maps functionality in the presence of erroneous perception subsystem inputs which enhances the overall safety and reliability of the autonomous vehicles.

The Current Icing Product (CIP) provides an hourly diagnosis of the severity of icing occurring based on multiple data sources. Pilot reports (PIREPs) and surface observations (METARs), as well as satellite, numerical weather prediction (NWP) model, radar, and lightning data are all utilized within the algorithm. The accurate identification of cloud base is a large factor in the algorithm's determination of icing severity. Current methods employ the METAR observation of ceiling to identify the cloud base over a specified area within the CIP domain. The temperature from the Rapid Update Cycle (RUC) NWP model at the height of the observed METAR ceiling can be utilized as a proxy for the amount of condensate in the cloud. The likelihood of a large amount of condensate in the identified cloud increases with increasing cloud base temperature. As the amount of liquid water diagnosed by CIP severity increases, so does the estimated icing severity.

NASA, the FAA, DoD, and NOAA have teamed with industry and academia to develop a capability to detect icing conditions ahead of aircraft using onboard or ground-based remote sensing systems. The goal of the program is to provide pilots with sufficient information to allow avoidance of icing. Information displayed to the pilot, as a measure of icing potential, will be useful in assessing the risk of entering the sensed conditions. This requires measurement and mapping of cloud microphysical parameters, especially cloud and precipitation liquid water content, droplet size and temperature, with range. Remote measurement of cloud microphysical conditions has been studied for years. However, this is the largest focused program devoted to remotely detect aircraft icing conditions. Primary funding sources are NASA Aerospace Operations Systems, the FAA Aviation Weather Research Program and William J.

When examining the literature on the adhesion strength of impact ice, there have been a wide range of methodologies tried to measure the required stresses to induce interfacial delamination. Utilizing the Icing Research Tunnel at the NASA Glenn Research Center to generate the impact ice required for this work, several different mechanical tests have been and are being developed to determine the stresses along the interface between ice and coupon. This set of tests includes the technical mature modified lap joint test which has been used to conduct ice adhesion studies through a wide sweep of icing conditions. To conduct in situ ice adhesion measurements inside of the Icing Research Tunnel, several new experiments are currently being developed to make ice adhesion measurements during and immediately after ice accretion.