Search Results

The ways in which vehicles are used in the field are continually becoming more diverse. In order to provide the optimum solution with respect to performance and weight, it is necessary to be able to assure vehicle endurance reliability with a high degree of accuracy in relation to the manner of use in each market. This situation has increased the importance of accurately quantifying the ways in which vehicles are used in the field and of designing vehicles with sufficient endurance reliability to match the usage requirements. This report presents a “market model” by which the manner of usage in the field can be treated quantitatively using combinations of environmental factors that influence the road load, drive load and corrosion load, representing typical loads vehicles must withstand.

A safety support system that uses information received from the road infrastructure is being developed in a project sponsored by the Ministry of Land, Infrastructure and Transport. The purpose of this system is to reduce the number of accidents at intersections and on highways. The system is now being tested in an experimental vehicle. This paper describes what kind of information is helpful to drivers based on the experimental results.

Brake judder caused by uneven heat spots on brake disc surfaces is a major issue in improving vehicle quality. This is especially true for rumble that occurs during high-speed braking. In order to determine the excitation mechanism of brake judder, it is necessary to measure the dynamic brake disc geometry and temperature distribution during actual operation on the road. A noncontact sensor system, suitable for a high temperature environment, was used to monitor these parameters, making it possible to visualize heat spots transiently. The data obtained revealed the influence of pad and disc parameters on heat spot formation.

This paper deals with a vehicle detection method for realizing a blind spot warning function, under various environmental conditions. We introduced a method that is capable of discriminating the target object vehicles, under poor lighting conditions and in cases where the lens may be exposed to splashes in wet, snow and dirt roads. The image sensing of the vehicle detection consists of four functional components: obstacle detection, velocity estimation, vertical edge detection, and final classification. Such componets allow robust performances resembling geometry based approaches, with low calculation power as an apperance based approach. This paper describes the functional components, and furthermore methods to enhance the performances under low contrast conditions and also suppress false detections caused by residue on the lens, which becomes essential for installation on vehicles driven in actual road conditions.

In making driver workload assessments, it is important to evaluate the driver's level of brain activity because the operation of a motor vehicle presumably involves higher-order brain functions. Driving on narrow roads in particular probably imposes a load on the driver's brain functions because of the need to be cognizant of the tight space and to pay close attention to the surroundings. Test vehicles were fitted with a functional near-infrared spectroscopy (fNIRS) system for measuring bloodstream concentrations at 32 locations in the frontal lobe of the participating drivers in order to evaluate their levels of mental activity while driving on narrow roads. The results revealed significant increases in cerebral blood flow corresponding to the perceived workload. This suggests that increases in cerebral blood flow can be used as an effective index for estimating mental workloads.

Eliminating squeal noise generated during braking is an important task for the improvement of vehicle passengers' comfort. Considerable amount of research and development works have been done on the problem to date. In this study, we focused on the analyses of friction self-excited vibration and brake part resonance during high frequency brake squeal. Friction self-excited vibration is caused by the dry friction between pads and rotor, and occurs as a function of their relative sliding velocities. Its vibration frequency can be calculated in relation to the mass and stiffness of the pad sliding surface. Frequency responses of the brake assembly were measured and the vibration modes of the pad, disc and caliper during squeal were identified through modal analysis. Further study led to the development of a computer simulation method for analyzing the vibration modes of brake parts. Analytical results obtained using the method agreed well with the corresponding experimental data.

Curbing emissions of carbon dioxide (CO₂), which is believed by many scientists to be a major contributor to global warming, is one of the top priority issues that must be addressed by automobile manufacturers. Automakers have set their own strategies to improve fuel economy and to reduce CO₂ emissions. Some of them include integrated approaches, focusing on not only improvement of vehicle technology, but also human factors (eco-driving support for drivers) and social and transportation factors (traffic management by intelligent transportation systems [ITS]). Among them, electric vehicles (EVs) will be a key contributor to attaining the challenging goal of CO₂ reduction. Mass deployment of EVs is required to achieve a zero-emission society. To accomplish that, new advanced technologies, new business schemes, and new partnerships are required.

After the turn of the century, growing social attention has been paid to environmental concerns, especially the reduction of greenhouse gas emissions and it comes down to a personal daily life concern which will affect the purchasing decision of vehicles in the future. Among all the sources of greenhouse gas emissions, the transportation industry is the primary target of reduction and almost every automotive company pours unprecedented amounts of money to reengineer the vehicle technologies for better fuel efficiency and reduced CO2 emission. Besides those efforts paid for sheer improvements of genuine vehicle technologies, NISSAN testified that “connectivity” with outside servers contributed a lot to reduce fuel consumption, thus the less emission of GHG, with two major factors; 1. detouring the traffic congestions with the support of probe-based real-time traffic information and 2. providing Eco-driving advices for the better driving behavior to prompt the better usage of energy.

Traction control systems (TCSs) serve to control brake pressure and engine torque, thereby reducing driving wheel spin for improved stability and handling. Systems are divided into two basic types by the brake control configuration. One type is a one-channel left-right common control system and the other is a two-channel individual control system. This paper presents an analysis of these two types of TCS configurations in terms of handling, acceleration, stability, yaw convergence and other performance parameters. The systems are compared with and without a limited-slip differential (LSD) under various road conditions, based on experimental data and computer simulations. As a result of this work, certain Nissan models are now equipped with a new Nissan Traction Control System with a rear viscous LSD (Nissan V-TCS), which provides both the advantages of a rear viscous LSD in a small slip region and a two-channel TCS in a large slip region.

THIS PAPER presents an advanced heads-up display which has been newly developed for use in 88 Nissan Silvia model. The HUD consists of a projector with a newly developed high brightness VFD and light-selective film used as a combiner which is coated on the windshield. This combination provides good display legibility even under bright sunlight. The display shows the vehicle speed in a three-digit reading at distance of more than one meter from the driver's eyes. The windshield-coated combiner conforms to U.S. safety standards concerning light transmittance, abrasion and other performance requirements. Experimental data are also presented which substantiate the HUD's high legibility and confirm its effect in enhancing the driver's attention toward the road ahead

HEV and EV markets are in a rapid expansion tendency. Development of low-cost regenerative cooperation brake system is needed in order to respond to the consumers needs for HEV and EV. Regenerative cooperation brake system which HEV and EV are generally equipped with has stroke simulator. We developed simple composition brake system based on the conventional ESC unit without the stroke simulator, and our system realized a low-cost regenerative cooperation brake. The key technologies are the quiet pressurization control which can be used in the service application, which is to make brake force depending on brake travel, by gear pump and the master cylinder with idle stroke to realize regenerative cooperation brake. Thanks to the key technologies, both the high regenerative efficiency and the good service brake feeling were achieved.

This paper describes a headway distance control system for platoon driving on an automated highway system (AHS). The system implemented on a test vehicle is described first, followed by a description of a vehicle control method based on the use of throttle and brake actuators. This method makes it possible to obtain the target acceleration and deceleration regardless of the vehicle speed range and the rate of acceleration or deceleration. Experimental and simulation results obtained with this method are presented. A control method is then described that uses inter-vehicle communication and laser radar to maintain a constant headway between vehicles. The results of simulations and driving tests conducted with three vehicles are presented to illustrate that the use of inter-vehicle communication is highly effective in improving headway control performance.

This paper describes a new 5.6-liter DOHC V8 engine, VK56DE, which was developed for use on a new full-size sport utility vehicle and a full-size pickup truck. To meet the demands for acceleration performance when merging into freeway traffic, passing or re-acceleration performance from low speed in city driving and hill-climbing or passing performance when towing, the VK56DE engine produces high output power at top speed and also generates ample torque at low and middle engine speeds (90% of its maximum torque is available at speeds as low as 2500 rpm). Furthermore, this engine achieves top-level driving comfort in its class as a result of being derived from the VK45DE engine that was developed for use on a sporty luxury sedan. Development efforts were focused on how to balance the required performance with the need for quietness and smoothness.

An Adaptive Cruise Control system with stop-and-go capability has been developed to reduce the driver's workload in traffic jams on expressways. Based on an analysis of driving behavior characteristics in expressway traffic jams, a control system capable of modeling those characteristics accurately has been constructed to provide natural vehicle behavior in low-speed driving. The effectiveness of the system was evaluated with an experimental vehicle, and the results confirmed that it reduces the driver's workload. This paper presents an outline of the system and its effectiveness along with the experimental results.

This paper presents the electrically driven intelligent brake system that has been developed for electric vehicles, which are expected to penetrate markets rapidly amid the ongoing energy paradigm shift. This brake system achieves a cooperative energy regeneration function and high responsiveness while providing braking performance, system reliability and vehicle mounting ease equal to that of conventional brake systems with a vacuum booster. This paper outlines the newly developed brake system and describes how to decide the target brake force which is achieved a regenerative braking capability for recovering energy efficiently without sacrificing braking.

An electrically-driven, intelligent brake unit has been developed, to be combined with a regenerative braking system in electric vehicles (EVs) and hybrid electric vehicles (HEVs) which went into production in 2010 - 11. The brake pedal force is assisted by an electrically driven motor, without using vacuum pressure, unlike conventional braking systems. The actuator can be implemented to coordinate with a regenerative braking system, and to have adjustable pedal feel through use of a unique pressure-generating mechanism and a pedal-force compensator. In this paper, we describe features of the actuator mechanism and performance test results

To promote widespread use of fuel cell vehicles (FCVs), further improvement of cold start capability is required for operation in various extreme temperature regions all over the world. Sub-freezing, cold start issues of fuel cells must be resolved through gaining a better understanding of the physical phenomena taking place in a cell during cold start and by elucidating the mechanisms hindering cold startup. Nissan has improved its understanding of the physical phenomena occurring in a fuel cell (FC) during cold startup by a laboratory-scale FC experiment at subfreezing temperatures and a numerical calculation that expresses various transport processes in a fuel cell, including those of the reactant gases, water, electrons and heat. The results have identified several necessary conditions for mass transport in a cell during cold startup and the factors that limit and govern the phenomena involved.

A new analysis procedure have been developed that evaluate a brake system performance based on analyses of the transient characteristics and frequency characteritics in the brake piping. Using this procedure, analyses were made of the effect of ABS operation on brake pressure changes and of the influence of the orifice on the pressure transmission characteristics. As an example of a frequency analysis, the pressure transmission characteristics were analyzed when pulse pressure occured in the brake piping as a result of variation in the wall thickness of the brake rotors. This paper presents the results of these analyses and shows the validity of the new procedure through a comparison with experimental data.

An important factor in the development of vehicle suspensions has been how to get higher performance from both ride and stability, which are normally in conflict. In addressing this problem, we analyzed the optimum damping forces of shock absorbers for various driving conditions and developed an electronically controlled shock absorber system, which we call “Super Sonic Suspension” based on the results. Through this microcomputer-controlled system, we achieved a great improvement in riding comfort by being able to the damping force much lower than before, based on the results of said analysis. At the same time, stability of the vehicle was also improved by optimumly controlling the damping force for various driving conditions through signals from a newly developed road sensor, which utilizes supersonic waves, and other sensors.

This paper describes an image processing system for tracking a traffic lane by recognizing white lines on the road ahead. The system utilizes the features of the white lines and the Hough transformation to detect white line candidate points in images taken with a CCD camera. The parameters of the road configuration and vehicle attitude are estimated with an extended Kalman filter. This system has been applied to achieve a lane-keeping assistance system that provides steering control based on the host vehicle’s lateral position in its lane.