Search Results

IMEP can be generally calculated by numerical integration on the PV diagram. However, this method requires a great number of sampled data per cycle, in order to ensure high accuracy in calculation. The present method is a to use only the primary and secondary components of engine speed from the pressure diagram based on the Fourier series. Owing to this method, calculation errors have become smaller than conventional method even though the number of samples is reduced, and calculation time is also reduced by the conventional method. Using present method, a Fourier series type combustion analyzing system has been developed. Real-time IMEP measurement is allowed in this system owing to the characteristic features described above, and the validity of calculated results is confirmed by comparing the results with the IMEP values obtained by batch processing through the numerical integration.

Gas chromatographic methods for analyzing hydrocarbon species in vehicle exhaust emissions were compared in terms of their collection efficiency, detection limit, repeatability and number of species detected using cylinder gas and tailpipe emission samples. The main methods compared were a Tenax cold trap injection (TCT) method (C5-C12 HCs) and a cold trap injection (CTI) method (C2-C4 HCs; C5-C12 HCs). Our own direct (DIR) method was used to confirm the collection efficiencies. Both methods yielded good results, but the CTI method showed low collection efficiency for some C2-C4 HCs. Measurement of individual species is needed with this method for accurate analysis of tailpipe emissions. Both the CTI method and the TCT method combined with the DIR method for determining C2-C4 HCs yielded nearly the same ozone specific reactivity values for the NMHC species analyzed.

This paper describes the relationship between the design parameters used to define the geometry of an automotive torque converter and the resultant efficiency in relation to the internal flow characteristics. Taking the turbine bias angle and the contraction ratio of the pump flow passage as specific examples, the effects of each design parameter on the internal flow characteristics and the occurrence of loss were analyzed. A three-dimensional viscous flow analysis code was used in the numerical computation procedure and a method developed independently by the authors was used in the loss analysis. The flow near the wall was visualized experimentally using a technique resembling the so-called oil film method. The visualized results showed good qualitative agreement with the numerical analysis results.

Research is under way on an engine system [1] that achieves a variable compression ratio using a multiple-link mechanism between the crankshaft and pistons for the dual purpose of improving fuel economy and power output. At present, there is no database that allows direct judgment of the feasibility of the specific sliding parts in this mechanism. In this paper, the feasibility was examined by making a comparison with the sliding characteristics and material properties of conventional engine parts, for which databases exist, and using evaluation parameters based on mixed elasto-hydrodynamic (EHD) lubrication calculations. In addition, the innovations made to the mixed EHD calculation method used in this study to facilitate calculations under various lubrication conditions are also explained, including the treatment of surface roughness, wear progress and stiffness around the bearings.

Maintaining reliability of the connecting rod bearing is a very important subject, and the following is a problem that needs to be overcome. Predicting reliability has generally depended on minimum oil film thickness (M.O.F.T), but recently, the engines of passenger cars which have greater power and speed potential than conventional ones are sometimes run beyond their M.O.F.T. limit (a degree of roughness around the crank shaft's axis.) In such a case, it is so difficult to predict reliability according to M.O.F.T., that we need a new index which directly shows seizure and wear. For this purpose, we found that the crank shaft pin temperature can be a key cause of seizure and wear according to an analysis of the relationship between its temperature and the seizure and wear caused intentionally. Using this method, we confirmed that the combination of bearing and crank shaft materials is very important for preventing seizure and wear.

Nissan has developed a new GA16DE engine for use in the new 1991 Sentra. The major development aims for this engine were to achieve ample torque at low to intermediate engine speed and smooth throttle response. These aims, of course, had to be compatible with good fuel economy, quietness, maintenance-free operation and high reliability. In addition, It was necessary to achieve a compact package size despite the twin-cam design. All of those objectives have been attained through the use of a super-long and aerodynamic intake system, variable valve timing control, a low friction, maintenance-free, direct acting valve system, dual direction fuel injectors, and a two-stage cam drive system. This paper discuss the major development objectives, basic engine structure and principal component parts.

A flatter design is becoming increasingly important for reducing torque converter axial size and weight. The conventional stator design method, in which the blade profile is geometrically determined and flow analysis of the profile may give some valuable information, is no longer sufficient for achieving efficient flow turning in the short axial length of flat torque converters. Here, after a brief review of the conventional design approach, an inverse design method is introduced, which yields a blade profile solution for a prescribed favorable velocity distribution along the blade. The performance improvement with this procedure has been demonstrated experimentally.

There has been a growing need to develop more compact automatic transmissions with a greater number of speeds for better fuel economy and better driveability. This study investigated a method for determining suitable planetary gear trains for today's transmissions. A computer program has been developed for application to five-speed transmissions consisting of two planetary gearsets. By analyzing various gear train possibilities, the program can identify which gearsets are suitable for different conditions, including the number of speeds, the number of binding elements, topological suitability and other factors.

An electronically controlled five-speed automatic transmission has been developed for use in new 2-liter models. This high-performance gearbox is the world's first five-speed automatic transmission for passenger car use to be equipped with a torque converter. It is designed with an ultra-wide range and close ratio gearing and incorporates a host of outstanding technologies to provide excellent performance and driveability. This paper describes the major features and performance of this new automatic transmission and some of the studies undertaken concerning multiplication of gear steps.

As a new generation sports car engine to lead the field in the 1990s, a 3.0 liter, 60°V, type 6 cylinder, 4 cam, 24 valve engine (VG30DETT) has been developed to achieve the utmost in high performance levels and reliability. it has been mounted on the new model 300ZX and announced in the North America and Japanese markets. The VG30DETT engine is based on the previous VG30DE engine (the engine mounted on the former model 300ZX designed for the market in Japan). The main components, the major driving and the lubrication systems including such parts as the crank shaft,con-rod, cylinder block, piston, exhaust manifold, and oil pan of the VG30DE were thoroughly reviewed and revised. The VG30DETT engine is the result of redesigning the structure of the engine itself and its parts and components to assure durability under, high-level performance requirements.

Gasoline engines employ various mechanisms for improvement of fuel consumption and reduction of exhaust emissions to deal with environmental problems. Direct fuel injection is one such technology. This paper presents a new quasi-dimensional combustion model applicable to direct injection gasoline engine. The Model consists of author's original in-cylinder turbulence and mixture homogeneity sub model suitable for direct fuel injection conditions. Model validation results exhibit good agreement with experimental and 3D CFD data at steady state and transient operating conditions.

A mixed timescale subgrid model of a large eddy simulation was used to simulate the turbulence regime in diesel engine combustion. The combustion model used the direct integration approach with a diesel oil surrogate mechanism (developed at Chalmers University of Technology and consisting of 70 species and 309 reactions). Additional reactions for the generation and consumption of OH*, CO2*, and CH* species were added from recent kinetic studies. Collisional quenching and spontaneous emission resulted in de-excitation of the excited state radical. A phenomenological soot formation model (developed at Waseda University) was combined with the LES code. The following important steps were considered in the soot model: particle inception where naphthalene grows irreversibly to form soot, surface growth with the addition of C2H2, surface oxidation (induced by OH radicals and O2 attack), and particle coagulation.

An engine cycle simulation code with detailed chemical kinetics has been developed to study Homogeneous Charge Compression Ignition (HCCI) combustion with hydrogen as the fuel. In order to attain adequate combustion duration, resulting from the self-accelerating nature of the chemical reaction, fuel and temperature inhomogeneities have been brought to the calculation by considering the combustion chamber to have various temperature and fuel distributions. Calculations have been done under various conditions including both perfectly homogeneous and inhomogeneous cases, changing the degree of inhomogeneity. The results show that intake gas temperature is more dominant on ignition timing of HCCI than equivalence ratio and that there is a possibility to control HCCI by introducing appropriate temperature inhomogeneity to in-cylinder mixture.

The method for measuring air-fuel ratio is generally based on analysis of the exhaust gas components and its calculations. A new instrument has been developed which uses this method, but it attaches an oxygen sensor for exhaust gas analysis to the exhaust pipe and calculates the air-fuel ratio directly from the sensor output using a microprocessor. The response time of this instrument is 100 milliseconds and because it does not require an exhaust gas sampling system its weight is only 2.5 kg. This paper describes the operation theory, construction and characteristics of this instrument, as well as the results of air-fuel ratio of measurements on engines and vehicles using this instrument in a transient state.

The 4th Workshop of the Engine Combustion Network (ECN) was held September 5-6, 2015 in Kyoto, Japan. This manuscript presents a summary of the progress in experiments and modeling among ECN contributors leading to a better understanding of soot formation under the ECN “Spray A” configuration and some parametric variants. Relevant published and unpublished work from prior ECN workshops is reviewed. Experiments measuring soot particle size and morphology, soot volume fraction (fv), and transient soot mass have been conducted at various international institutions providing target data for improvements to computational models. Multiple modeling contributions using both the Reynolds Averaged Navier-Stokes (RANS) Equations approach and the Large-Eddy Simulation (LES) approach have been submitted. Among these, various chemical mechanisms, soot models, and turbulence-chemistry interaction (TCI) methodologies have been considered.

A robotic driver has been designed on the basis of an analysis of a human driver's action in following a given driving schedule. The self-learning algorithm enables the robot to learn the vehicle characteristics without human intervention. Based on learned relationships, the robotic driver can determine an appropriate accelerator position and execute other operations through sophisticated calculations using the future scheduled vehicle speed and vehicle characteristics data. Compensation is also provided to minimize vehicle speed error. The robotic driver can reproduce the same types of exhaust emission and fuel economy data obtained with human drivers with good repeatability. It doesn't require long preparation time. Thereby making it possible to reduce experimentation work in the vehicle development process while providing good accuracy and reliability.

Technologies for improving the fuel economy of gasoline engines have been vigorously developed in recent years for the purpose of reducing CO2 emissions. Increasing the compression ratio is an example of a technology for improving the thermal efficiency of gasoline engines. A significant issue of a high compression ratio engine for improving fuel economy and low-end torque is prevention of knocking under a low engine speed. Knocking is caused by autoignition of the air-fuel mixture in the cylinder and seems to be largely affected by heat transfer from the intake port and combustion chamber walls. In this study, the influence of heat transfer from the walls of each part was analyzed by the following three approaches using computational fluid dynamics (CFD) and experiments conducted with a multi-cooling engine system. First, the temperature rise of the air-fuel mixture by heat transfer from each part was analyzed.

A continuously variable valve event and lift (VEL) system, actuated by oscillating cams, can provide optimum lift and event angles matching the engine operating conditions, thereby improving fuel economy, exhaust emission performance and power output. The VEL system allows small lift and event angles even in the engine operating region where the required intake air volume is small and the influence of valvetrain friction is substantial, such as during idling. Therefore, the system can reduce friction to lower levels than conventional valvetrains, which works to improve fuel economy. On the other hand, a distinct feature of oscillating cams is that their sliding velocity is zero at the time of peak lift, which differs from the behavior of conventional rotating cams. For that reason, it is assumed that the friction and lubrication characteristics of oscillating cams may differ from those of conventional cams.

There have been strong demands recently for reductions in the fuel consumption and exhaust emissions of diesel engines from the standpoints of conserving energy and curbing global warming. A great deal of research is being done on new emission control technologies using direct-injection (DI) diesel engines that provide high thermal efficiency. This work includes dramatic improvements in the combustion process. The authors have developed a new combustion concept called Modulated Kinetics (MK), which reduces smoke and NOx levels simultaneously by reconciling low-temperature combustion with pre-mixed combustion [1, 2]. At present, research is under way on the second generation of MK combustion with the aim of improving emission performance further and achieving higher thermal efficiency [3]. Reducing heat rejection in the combustion chamber is effective in improving the thermal efficiency of DI diesel engines as well as that of MK combustion.

The mechanism causing in-cylinder injector tip soot formation, which is the main source of particle number (PN) emissions under operating conditions after engine warm-up, was analyzed in this study. The results made clear a key parameter for reducing injector tip soot PN emissions. An evaluation of PN emissions for different amounts of injector tip wetting revealed that an injector with larger tip wetting forms higher PN emissions. The results also clarified that the amount of deposits does not have much impact on PN emissions. The key parameter for reducing injector tip soot is injector tip wetting that has a linear relationship with injector tip soot PN emissions.