Search Results

The aim of this work is to propose modifications to the managing of the 1st generation Common Rail injectors in order to reduce actuation time towards multiple injection strategies. The current Common Rail injector driven by 1st ECU generation is capable of operating under stable conditions with a minimum dwell between two consecutive injections of 1.8 ms. This limits the possibility in using proper and efficient injection strategies for emission control purposes. A previous numerical study, performed by the electro-fluid-mechanical model built up by Matlab-Simulink environment, highlighted different area where injector may be improved with particular emphasis on electronic driving circuit and components design. Experiments carried out at injector Bosch test-bench showed that a proper control of the solenoid valve allowed reducing drastically the standard deviation during the pilot pulses.

In the next incoming future the necessity of reducing the raw emissions leads to the challenge of an increment of the thermal engine efficiency. In particular it is necessary to increase the engine efficiency not only at full load but also at partial load conditions. In the open literature very few technical papers are available on the partial load conditions analysis. In the present paper the analysis of the effect of the throttle valve rotational direction on the mixture formation is analyzed. The engine was a PFI 4-valves motorcycle engine. The throttle valve opening angle was 17.2°, which lays between the very partial load and the partial load condition. The CFD code adopted for the analysis was the FIRE AVL code v. 2013.2. The exhaust, intake and compression phases till TDC were simulated: inlet/outlet boundary conditions from 1D simulations were imposed.

The paper presents a study made to define the optimal parameter configuration, which enables the mixture preparation, and ignition systems to perform a low-temperature engine start by pure ethanol fuelling without misfiring or failure. A numerical virtual engine, simulating the behavior of a real small displacement 8 valves passenger car engine, is set up to describe and understand the physical phenomena of mixture preparation, spatial and temporal in-cylinder mixture distribution and the ignition/combustion events. The complex phenomena, which govern the gas flow patterns and mixture formation in the intake port and the combustion chamber are particularly analyzed during low-temperature engine cranking. Furthermore is discussed the influence of open and closed valve injection modes.

An exhaust system comprises at least one muffler, the back pressure generated by the muffler exponentially grows as the engine speed increases. Accordingly, fuel consumption and direct CO2 emissions are penalized due to the back pressure generated by the muffling body in order to reduce noise emissions. To obviate this, it has been suggested to construct an exhaust system with two differentiated paths according to the engine speed, so that at low speeds the exhaust gases follow a first high acoustic attenuation (high back pressure) path, while at high speeds (high exhaust gas pressure), the exhaust gases follow a second low acoustic attenuation (low back pressure) path. Simulation and experimental analysis will be presented. A control valve is provided to alternatively direct the exhaust gases along the desired path according to the engine speed. These control valves usually include an electric or electro-pneumatic actuator, but are heavy, large in size and expensive.

This paper documents an extensive study aimed at a better understanding of the peculiarities and performance of crankshaft mounted gerotor pumps for IC engines lubrication. At different extents, the modelling, simulation and testing of a specific unit are all considered. More emphasis, at the modelling phase, is dedicated to the physical and mathematical description of the flow losses mechanisms; the often intricate aspects of kinematics being deliberately left aside. The pressure relief valve is analysed at a considerable extent as is the modelling of the working fluid, a typically aerated subsystem in such applications. Simulation is grounded on AMESim, a relatively novel tool in the fluid power domain, that proves effective and compliant with user deeds and objectives. Testing, at steady-state conditions, forms the basis for the pro!gressive tuning of the simulation model and provides significant insight into this type of volumetric pump.

In PFI and GDI engines the tumble motion is the most important charge motion for enhancing the in-cylinder turbulence level at ignition time close to the spark plug position. In the open literature different studies were reported on the tumble motion, experimental and not. In the present paper the research activity on the tumble generation at partial load and very partial load conditions was presented. The added value of the analysis was the study of the effect of the throttle valve rotational direction on the tumble motion and the final level of turbulence at the ignition time close to the spark plug location. The focus was to determine if the throttle rotational direction was crucial for the tumble ratio and the turbulence level. The analyzed engine was a PFI 4-valves motorcycle engine. The engine geometry was formed by the intake duct and the cylinder. The CFD code was FIRE AVL code 2013.1.