Search Results

In certain types of city bus service some automatic transmission fluids can fail in less than 10,000 miles. In order to provide satisfactory transmission performance for longer mileage, improved fluids are required. An investigation was undertaken to obtain improved fluids. Fifteen different fluid formulations were evaluated in 30 city buses operated in normal service for more than 2,000,000 miles. It was determined that fluids fail because of frictional deterioration and oxidation. Based on these evaluations, only two fluids were found to be satisfactory for more than 40,000 miles; one additional fluid was satisfactory for more than 30,000 miles. The remaining 12 fluids failed in less than 20,000 miles.

During development of the General Motors rotary engine, the lubricant was recognized as important to its success because certain lubricants produced deposits which tended to stick both side and apex seals. Consequently, it was decided to develop a rotary engine-dynamometer test, using a Mazda engine, which could be used for lubricant evaluation. In an investigation using an SE engine oil with which there was rotary engine experience, engine operating variables and engine modifications were studied until the greatest amount of deposits were obtained in 100 h of testing. The most significant engine modifications were: omission of inner side seals, plugging of half the rotor bearing holes, pinning of oil seals, grinding of end and intermediate housings, and using a separate oil reservoir for the metering pump. Using this 100 h test procedure, three engine oils and five automatic transmission fluids were evaluated.

Effective performance of functional automotive components requires fluid sealing under compatible conditions. One method of determining this compatibility is through the use of immersion testing under a variety of conditions that simulate those experienced in actual use. By measuring the changes in the physical properties of the seal materials after immersion a judgment can be made regarding seal/fluid compatibility which will be encountered later in actual use. A series of immersion tests using representative seal materials and automotive fluids; namely, gear oils, transmission fluids, and motor oils were conducted within the framework of the Technical Committee on Automotive Rubber, jointly sponsored by SAE-ASTM.

A LOW-TEMPERATURE study of the relationship between the performance of a step-type automatic transmission and the transmission fluid viscosity is reported in this paper. It is shown that the low-temperature malfunction of these units is due to the viscometric properties of the fluid and that at the temperature at which the fluid reaches a certain critical viscosity the transmission will fail. A mathematical analysis of the mechanism of failure supports the conclusions drawn from the experimental study.*

One of the prime requisites for automobile radar systems is obstacle hazard evaluation, the extent needed being dependent upon the particular system application. Much of the information necessary for a radar system to assess the degree of hazard of a target must come from characteristics which can be measured by the radar itself. While the hazard evaluation capacity has not yet been developed for automobile radar systems, research to provide this capability is in progress. Continuous wave (CW) scattering measurements have been made in a manner which is consistent with automobile radar operation. Various aspects of simple targets and of an automobile were measured in a microwave anechoic chamber. Both horizontal and vertical linear polarizations were transmitted and their co-linear and cross polarizations received. These data have been used to confirm the existence of and to understand certain scattering mechanisms.

As the design of automobiles changed over the past seventy years, manufacturers have increased the usage of decorative trim to further enhance the beauty of styling concepts. As new trim materials were introduced and parts became more complicated in design, producers have continued their efforts to produce decorative trim parts which remain attractive during the service life of the automobile. The service performance of trim materials in several geographic locations, the use of accelerated tests to predict service performance, recent developments in improving the durability of plated parts, and requirements for producing quality exterior decorative trim are reviewed in this paper.

EXTENSIVE TESTING by GM Research Laboratories has screened five promising transaxle fluids out of 32 mineral-oil-base fluids, 10 synthetic-base fluids, and numerous additive-base stock combination fluids. This paper discusses the findings of the testing and the continuing program on the five fluids. Transaxle fluids have a number of properties affecting performance, including: High-temperature viscosity. Low-temperature fluidity. Shear resistance. Friction properties. Oxidation resistance. Antifoam quality. Effect on seals. Fluid-clutch plate compatibility. Antiwear quality. Extreme-pressure quality. Antirust and anticorrosion qualities.*

This paper illustrates by way of two practical examples, namely, transmission gears and crankshafts, how the automotive industry applies basic approaches and methods for achieving fatigue resistant design. Analytic, laboratory, and field studies necessary in the development of these components are briefly outlined.

A general purpose data acquisition system has been developed which converts analog data to scaled, tabulated, and graphical output. A scanning synchronization unit ensures that each input channel is sampled synchronously with input data pulses. System input can be either direct from the test area or from an analog tape recorder, in which case time expansion is possible by the use of high record-low play/back speeds. A computer program controls the analog to digital conversion process. The on-line control of the program minimizes the subsequent data reduction, and through the use of input parameters, flexibility is attained in data formatting. The data reduction error is less than 1% and statistical programs included in the system provide estimates of the quality of the input data. The entire system including all associated hardware and software is described in detail, using acquisition of pressure data synchronously with crank angle as an example.

This paper describes a computer study made by the General Motors Corp. Research Laboratories to determine what percentage of the energy supplied to the axle of a passenger car is available for recovery through regeneration. Several weight classes of passenger cars were studied using three driving schedules-city, suburban, and highway. For each vehicle run in accordance with the prescribed driving schedules, two ratio percentages were obtained: (1) the ratio of energy available for recovery to the total energy supplied to the axle, and (2) the above ratio modified by assumed efficiencies in the propulsion and regeneration systems.

A brief review of the testing of automatic transmission fluid for compatibility with seals is presented. The total immersion test used in fluid qualification, while apparently effective in predicting the compatibility of fluids and seals in service, does not correlate well with transmission tests with respect to hardness change of piston seals. The Dip-Cycle Test, developed to overcome this limitation, is a procedure for alternately immersing seal specimens in the test fluid and suspending them in the hot air-fluid vapor atmosphere above the fluid. Correlation of the Dip-Cycle Test with transmission piston seal results is much improved over that with the total immersion test. It is the purpose of this paper to review these developments and to present an improved test procedure (dip cycle test) for evaluating the effect of fluids on transmission piston seal materials.

The Total Immersion Test (ASTM D 471) for seal elastomers, used in evaluating the compatibility of fluids and seals for automatic transmissions, does not, produce hardness and volume change results similar to those found for rotating shaft seals in service. The Tip Cycle Test was devised to provide better agreement with service results. In the test, one side of the seal is exposed to air, and the other alternately to fluid and to air-fluid vapor. Rotating shaft seals were evaluated in both car and dynamometer transmission tests, and in various bench tests. Agreement was poor between transmission tests and both the Total Immersion and the Dip Cycle Tests. Good agreement was found with the Tip Cycle Test.

Tests were conducted using older model cars with automatic transmissions to determine the effect of fluid composition on leakage past the rotating shaft seals. It was found that seal leakage was reduced or stopped by changing to seal-swelling fluids, and increased with seal-shrinking fluids. Leakage was also reduced by adding aromatic additives to existing fluids in the transmissions. Seal volume and hardness change results from bench tests support the car data.

Controlled-slip differentials (CSD) improve car operation under wheel slipping conditions. The performance of CSD's is dependent upon two criteria associated with clutch friction: “chatter” and “effectiveness.” “Chatter” is an undesirable noise which may occur during differential action. “Effectiveness” is a measure of the ability of the CSD clutches to transfer torque, during wheel slippage, to the wheel with the greater traction. The objective of this investigation was to definitely establish the cause of chatter, measure CSD effectiveness, and relate friction characteristics of lubricants to CSD operation. In tests with an instrumented car, it was found that both chatter and effectiveness are strongly influenced by the lubricant. Chatter occurred with lubricants that produced an increase in clutch friction with decreasing sliding speed. Chatter did not occur with lubricants containing friction modifiers which produced a decrease in clutch friction with decreasing sliding speed.

THIS PAPER discusses the Stirling thermal enging from four points of view: 1. The ideal, thermodynamic point of view, showing the inherent potentialities of the ideal Stirling cycle in comparison to the basic cycles of other engines. 2. The physical engine and its method of operation with respect to the ideal cycle and the limitations of practical mechanics. 3. Performance data from the first modern Stirling engines ever operated in the United States, evaluating the relationship between the new engine and other more familiar engines of similar sizes. This comparative discussion serves to demonstrate the advantages and disadvantages of the Stirling engine and to indicate its proper place in the 1960 family of prime movers. 4. A look backward into the century of history behind the modern engine pointing out significant milestones in the engine's development.

At the 1970 SAE International Automobile Safety Conference, the first experimental chest impact results from a new, continuing biomechanics research program were presented and compared with earlier studies performed elsewhere by one of the authors using a different technique. In this paper, additional work from the current program is documented. The general objective remains unchanged: To provide improved quantification of injury tolerance and thoracic mechanical response (force-time, deflection-time, and force-deflection relationships) for blunt sternal impact to the human cadaver. Fourteen additional unembalmed specimens of both sexes (ranging in age from 19-81 years, in weight from 117-180 lb, and in stature from 5 ft 1-1/2 in to 6 ft) have been exposed to midsternal, blunt impacts using a horizontal, elastic-cord propelled striker mass. Impact velocities were higher than those of the previous work, ranging from 14-32 mph.

Forces necessary for fracture under localized loading have been obtained experimentally for a number of regions of the head. Three of these, the frontal, temporoparietal, and zygomatic, have been studied in sufficient detail to establish that the tolerances are relatively independent of impulse duration, in contrast with the tolerance of the brain to closed-skull injury. Significantly lower average strength has been found for the female bone structure. Other regions reported upon more briefly are mandible, maxilla, and the laryngotracheal cartilages of the neck. Pressure distribution has been measured over the impact area, which has been 1 sq in. in these tests, and the relationship between applied force as measured and as predicted from a head accelerometer is examined.

As part of General Motors effort to improve fuel economy, the effects of engine and power train lubricant viscosities were investigated in passenger car tests using either high- or low- viscosity lubricants in the engine, automatic transmission, and rear axle. Fuel economy was determined in both constant speed and various driving cycle tests with the car fully warmed-up. In addition, fuel economy was determined in cold-start driving cycle tests. Using low-viscosity lubricants instead of high-viscosity lubricants improved warmed-up fuel economy by as much as 5%, depending upon the differences in lubricant viscosity and type of driving. Cold-start fuel economy with low-viscosity lubricants was 5% greater than that with high-viscosity lubricants. With such improvements, it is concluded that significant customer fuel economy gains can be obtained by using the lowest viscosity engine and power train lubricants recommended for service.

Noise produced by automotive ignition systems can deteriorate the performance of nearby communication systems. An important step toward alleviating this difficulty is to characterize the ignition noise. Measurements have been made of the noise peak amplitude distribution of a number of identically equipped vehicles over a fixed period of time. Both vertical and horizontal polarizations were used, and measurements were made at two frequencies, 145 and 230 MHz. These statistics were then compared to various probability distributions to attempt to characterize the amplitude distribution of the noise. The distributions studied were: the log-normal, the exponential, the Rayleigh, and the Weibull distributions. It was concluded that the best fit was provided by the Weibull distribution. The parameters of the best fitting distribution are primarily a function of the antenna's polarization, with frequency having only a minor effect.

To lower emissions from a multicylinder engine, the air-fuel ratio must be optimized in all cylinders. If uniform fuel distribution is achieved, then the cylinder-to-cylinder air distribution is of particular interest. A probe system has been developed to measure mass flow rates to individual cylinders during operation of a complete engine. Fast response measurements of pressure, temperature, and flow velocity are made in the intake port near the valve during the intake portion of the cycle. High-speed collection of the large volume of data was accomplished through on-line use of an IBM 1800 computer. A V8 455 CID (7457 cm3) engine with stock intake and single exhaust system was used in the initial application of the mass flow probe. Measurements of 30-40 individual cycles were combined to calculate the mean volumetric efficiency for each cylinder.