Search Results

Most transducers offered commercially are suitable for laboratory, aerospace, or industrial process applications but do not meet additional, stringent automotive requirements. A need exists, both present and future, for various types of transducers in automotive powerplant control systems. Possible electronic systems and subsystems requiring transducers are discussed, and the types of transducers needed for these systems are described along with a discussion of a general set of specifications with respect to accuracy, reliability, and durability. Substantial transducer development is needed to enhance the advancement of certain automotive electronic systems. This paper points out these requirements to the electronics industry in an effort to encourage a mutual industry development that will advance the technology.

Secondary air scheduling and average delivery rate have a great influence on the performance (carbon monoxide and hydrocarbon cleanup) of rich thermal manifold reactors. A continuously modulated secondary air system was devised to provide a tailpipe air-fuel ratio that did not change significantly with engine speed or load when a “flat” carburetion calibration was incorporated. This system involved throttling the inlet of the air pump(s) so that the air pump and engine intake pressures were equal. The continuous air modulation system was compared with an unmodulated system and a step-modulated system. The secondary air systems were investigated with both GMR “small volume” cast iron thermal reactors and Du Pont V thermal reactors on modified 350 CID V-8 engines in 1969 Chevrolet passenger vehicles. It was found that thermal reactor performance improved with each increase in control of the secondary air schedule.

A general purpose data acquisition system has been developed which converts analog data to scaled, tabulated, and graphical output. A scanning synchronization unit ensures that each input channel is sampled synchronously with input data pulses. System input can be either direct from the test area or from an analog tape recorder, in which case time expansion is possible by the use of high record-low play/back speeds. A computer program controls the analog to digital conversion process. The on-line control of the program minimizes the subsequent data reduction, and through the use of input parameters, flexibility is attained in data formatting. The data reduction error is less than 1% and statistical programs included in the system provide estimates of the quality of the input data. The entire system including all associated hardware and software is described in detail, using acquisition of pressure data synchronously with crank angle as an example.

Forces necessary for fracture under localized loading have been obtained experimentally for a number of regions of the head. Three of these, the frontal, temporoparietal, and zygomatic, have been studied in sufficient detail to establish that the tolerances are relatively independent of impulse duration, in contrast with the tolerance of the brain to closed-skull injury. Significantly lower average strength has been found for the female bone structure. Other regions reported upon more briefly are mandible, maxilla, and the laryngotracheal cartilages of the neck. Pressure distribution has been measured over the impact area, which has been 1 sq in. in these tests, and the relationship between applied force as measured and as predicted from a head accelerometer is examined.

A viscoelastic neck structure that responds to impact environments in a manner similar to the human neck is described. The neck structure consists of four ball-jointed segments and one pin-connected “nodding” segment with viscoelastic resistive elements inserted between segments that provide bending resistance as well as the required energy dissipation. Primary emphasis was placed on developing appropriate flexion and extension responses with secondary emphasis placed on axial, lateral, and rotational characteristics. The methods used to design the resistance elements for the neck structure are discussed. Three variations of the resistive elements have been developed that meet the response characteristics based on the data of Mertz and Patrick. However, no single resistive element has satisfied the flexion and extension characteristics simultaneously, but such an element appears to be feasible.

THIS REPORT deals with the major parameters of a seal application which affect its efficiency and life, as determined by controlled laboratory testing in CM Research Laboratories.* A. Shaft 1. Surface Roughness 2. Machining Lead B. Assembly C. Seal 1. Seal Diameter Control Trim Interference Spring Rate 2. Seal Lip Pressure Trim Interference Spring Rate Rubber Hardness Eccentricity 3. Seal Eccentricity Mold Register Assembly Trim

The Sealometer is used for evaluating the performance of lip type oil seals and provides a dimensionless number derived from measuring the increase in temperature of a test shaft operating in a lip seal for a given time interval. With the Sealometer it is possible to study parameters that affect seal performance. As a quality control instrument, the machine provides accurate data for design. Sealometer evaluation offers a quick method of determining the life expectancy of a particular design for a particular application and eliminates the need for long life test programs.

Two Highway Safety Research Institute (HSRI) dummies were tested and evaluated. Based on the analysis given, the HSI dummy should not be used for vehicle qualification testing. However, many of its components offer viable alternatives for future dummy development. The dummy was found to have inadequate biomechanical fidelity in the head, neck, and chest, although its characteristics were very promising and, as a whole, biomechanically superior to the Hybrid II. Its repeatability and reproducibility in dynamic component tests were better than the Hybrid II dummy. In particular, the HSRI friction joints were outstanding in repeatability and had a significant advantage in usability in that they do not require resetting between tests. In three-point harness and ACRS systems tests, the values of injury criteria produced by the HSRI dummy were generally lower than those obtained with the Hybrid II, especially the femur loads in the ACRS tests.

The following work was done in support of a continuing program to better characterize the behavior of the human chest during blunt sternal impact. Previous work on this problem has focused on determining the force-time, deflection-time, and force-deflection response of embalmed and fresh cadavers to impact by a 15 cm (6 in) diameter striker of variable mass traveling at velocities of 22.5-51 km/h (14-32 mph) and striking the sternum at the level of the fourth intercostal space. Additional questions persist concerning whether the anterior and posterior regions of the chest behave as highly damped masses or oscillate after impact, the relationship between force delivered to the surface of the body and the acceleration of the underlying regions, and the influence of air compressed in the lung on thoracic mechanics.

Renewal theory concerns itself with the replacement of randomly failing parts. In the simplest case we have a one component system which is kept running continuously by replacing a failed component at the instant of failure with an identical “new” component. The random variable N(t) = the number of failures (or replacements) to time t is then of interest in many types of reliability analysis. In this paper the distribution of N(t) is considered when the underlying failure law is a Weibull distribution. Tables of the mean and standard deviation of N(t) for various values of the Weibull slope parameter are presented. Applications to warranty and spare parts analyses are also noted.